Question about 2005 Chevrolet Uplander

1 Answer

Is there a problem with the wheel hub bearing which is under warrantee?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Chevrolet Master
  • 540 Answers

Unfortunately wheel hub/bearing assemblies only have a 3 year 36k warranty on them..

Posted on Oct 14, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace front hub assembly 2002 Suzuki XL7


the front wheel bearing hub?
XL-7 (the dash matters)
my wild guess, is the questions was
what are all steps to do this job. and tools.
that?
RTM?

https://suzukipitstopplus.com/Products/10056-2002-grand-vitara-xl-7-service-manual.aspx

http://www.fixkick.com/hubs/FW_BEARINGS.html#newer
the link shows all years, and variances.

here is a photo review, that is accurate up to
1998, and beyond , if you skip the bearing service parts. as yours are INTEGRATED
and NON-serviceable.
http://www.fixkick.com/hubs/FW_BEARINGS.html


the photo 6a and B
shows removing the hub,
so do that , buy a new hub and put it back
the same way, using the tool stated
at the stated ranges of torque
123-180 ft/lbs.
this range allows you to get the screws into the locking rings.

Dec 11, 2016 | 2002 Suzuki XL-7

2 Answers

Makes trobbing grinding noise when turning left


It could be a bad wheel bearing, and if so it probably is the passenger side, but check them both sides. Raise both wheels off the ground, or one at a time, and rock the wheel back and forth and up and down. The side with the bad bearing will have a lot more play in it.
To replace, the wheel "hub" with sealed bearing inside is replaced. The hub is bolted to the wheel knuckle, which supports the hub, the CV joint and axle shaft, the brake caliper and rotor, and the wheel itself. If you are experienced at car repair and have the proper tools, you can do it yourself. At a shop, expect a 2-4 hour labor bill, maybe under 2 hours if everything comes off easily. The cost of the hub and sealed bearing is probably less than $100, although prices can vary greatly.

May 13, 2015 | 1991 Cadillac DeVille

1 Answer

Rubbing noise


This will probably be the front C-V shaft or hub bearing. When in 2 wheel drive the C-V shaft will not have a load on it. But as soon as you change to 4 wheel drive the part has stress on it. It can also behave this way when the Hub bearing is asked to bear Torque from the turning C-V shaft. Instead of having slack from the weight of the truck pressing the Hub bearings straight up, the bearings are rotating under Torque and any play is magnified.

The rubbing can be the rotor, running on bad bearings and hitting the brake pads. As the rotor is bolted onto the Hub bearing, the rotor will tilt in harmony to the bad bearings in the Hub. This creates a misalignment as one side of the rotor is tilted creating a high side.

Feb 28, 2014 | Ford F-250 Cars & Trucks

1 Answer

How do i replace a wheel hub and wheel bearings on my 1997 Ford F250 Econoline?


you need to remove wheel brake caliper & caliper bracket. remove brake rotor . you will be at the hub bearing now. look on back of knucke there will be 4 bolts. remove bolts the tap on flang to pop out bearing, if truck has abs make sure you un plug sensor wire plug will be under rear part of wheel well

Jul 14, 2012 | Cars & Trucks

1 Answer

How to replace rear wheel bearing on 2003 hyandia sonata


Hub & Bearing Removal & Installation To Remove:
Hub bearing assembly (Typical) hyundai-08-00-6029.gif

  1. Release parking brake.
  2. Remove rear wheel assembly.
  3. Remove rear wheel speed sensor from carrier.
  4. Dismount brake caliper and support with mechanic's wire.
  5. Remove brake disc.
  6. Remove 4 axle hub mounting bolts. Special tool 09432-11000 (Typical) hyundai-08-00-6021.gif

  7. Using tool 09432-11000 (or suitable gear puller), remove tone wheel.
  8. Remove carrier.
  9. Remove stakes and remove flange nut.
  10. Support bearing outer race flange and press rear axle hub out.
  11. Using tool 09432-11000 (or suitable puller), remove inner race from axle hub.
To Install:
Hub bearing assembly (Typical) hyundai-08-00-6029.gif

  1. Apply thin coat of grease to bearing contact surface and hub.
  2. Using and appropriate tool, press bearing into hub. CAUTION
    Do not press against outer race of wheel bearing.
  3. Install flange nut and stake nut until it meets concave portion of spindle.
  4. Install carrier.
  5. Use an appropriate tool to press tone wheel.
  6. Install hub/bearing assembly with rounded portion of outer race facing up.
  7. Install 4 hub/bearing assembly bolts and rotate hub to seat bearing.
  8. Measure wheel bearing starting torque with a spring balance or equivalent device.
    • Starting torque should measure 15.9 in lb (1.8 Nm) or less
  9. Install brake disc.
  10. Mount brake caliper.
  11. Install rear wheel speed sensor to carrier.
  12. Install rear wheel assembly.
prev.gif next.gif

Oct 28, 2010 | 2001 Hyundai Sonata

1 Answer

How to change fornt drivers wheel bearing on grand vitara 2002 model 2.0 ltr 5 door and where can i get a repair manual for this model


REMOVAL & INSTALLATION
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Front wheel
    • Brake caliper and rotor
    • Locking hub or hub drive flange, if equipped
    • Hub grease cap, if equipped
    • Wheel speed sensor, if equipped
    • Wheel bearing lockwasher
    • Wheel bearing locknut and inner washer
    • Wheel hub and bearing assembly
    • Wheel hub oil seal
    • Wheel bearing oil seal
    • Snapring
  3. Press the wheel bearing and race out of the hub. To install:
  4. Press the wheel bearing and race into the hub so that the race is fully seated in the hub bore.
  5. Install or connect the following:
    • Snapring
    • Wheel bearing oil seal
    • Wheel hub oil seal
    • Wheel hub and bearing assembly
    • Wheel bearing locknut and inner washer. Tighten the nut to 157 ft. lbs. (216 Nm).
    • Wheel bearing lockwasher. Tighten the retaining screws to 13 inch lbs. (1.5 Nm).
    • Wheel speed sensor, if equipped
    • Hub grease cap, if equipped
    • Locking hub or hub drive flange, if equipped
    • Brake caliper and rotor
    • Front wheel
prev.gif next.gif --- Go to your local auto parts store or library to get a copy of the repair manual for this model.

Aug 26, 2010 | 2002 Suzuki Grand Vitara

1 Answer

How do i replace bad front wheel bearing ?


Replace the hub assembly which can be bought for $58 to $100 from various sources.

REMOVAL AND INSTALLATION
  1. Raise and safely support the vehicle.
  2. Place jackstands under the cradle and lower the vehicle slightly so the weight of the vehicle rests on the jackstands and not on the control arms.
  3. Remove the wheel assembly.
  4. Insert a drift punch into the rotor and remove the hub nut/washer.
  5. Remove the brake caliper, support and the rotor.
  6. Using the front hub spindle remover tool, separate the halfshaft from the hub.
  7. Remove the hub/bearing assembly-to-steering knuckle bolts and the hub/bearing assembly. To install:
  8. If replacing the seal, drive the seal towards the engine. Cut the seal off the halfshaft; be careful not to damage the halfshaft boot. NOTE: If the speed sensor bracket is removed or loosened from the steering knuckle, the speed sensor gap must be adjusted. If the speed sensor is removed from the bracket, speed sensor wax must be applied to the sensor before it is reinstalled in the bracket. Failure to apply the wax will permit corrosion and may result in sensor failure.
  9. To install the new grease seal, lubricate the with wheel bearing grease and using the hub seal installer tool, install the seal.
  10. Install the hub/bearing assembly-to-steering knuckle bolts and the hub/bearing assembly. Tighten the hub/bearing assembly-to-steering knuckle bolts to 70 ft. lbs. (95 Nm).
  11. Install the halfshaft to the hub.
  12. Install the rotor and caliper.
  13. Install the hub nut and washer. Tighten to 183 ft. lbs. (245 Nm).
  14. Install the wheel assembly.
  15. Remove the jackstands and lower the vehicle.
prev.gif next.gif

Jul 03, 2010 | 1996 Cadillac DeVille

3 Answers

Replace front wheel bearing is it hard to do on 2002 alero


its actually pretty easy if you have the basic tools needed and a little mechanical knowledge, because i dont think you can buy just the bearing at a auto parts store. they sell you the whole hub assembly which is great for the DIYer.

lift the car off the ground and block it from rolling and place a jack stand under it so it cant fall on anyone.


Wheel Bearings printpage_icon.gif

Removal & Installation

These vehicles are equipped with sealed hub and bearing assemblies. The hub and bearing assemblies are non-serviceable. If the assembly is damaged, the complete unit must be replaced.
  1. Before servicing the vehicle, refer to the precautions section.
  2. Remove or disconnect the following:
    WARNING DO NOT allow the caliper to hang unsupported from the brake hose.


    Front wheel Halfshaft nut and washer Caliper from the steering knuckle and support it aside


    Brake rotor Anti-lock Brake System (ABS) connector, if equipped 3 hub/bearing assembly bolts Halfshaft from the hub/bearing assembly Hub/bearing assembly

    0900c1528023b277.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Exploded view of the front hub/bearing assembly


To install:
Install or connect the following:

Hub/bearing assembly onto the halfshaft, making sure the splines engage smoothly Hub/bearing assembly to the steering knuckle. Torque the bolts to 70 ft. lbs. (95 Nm). Anti-lock Brake System (ABS) connector, if equipped Brake rotor Caliper onto the steering knuckle. Torque the bolts to 38 ft. lbs. (51 Nm). Halfshaft nut. Torque the hub nut to 284 ft. lbs. (385 Nm) on nuts colored black, or 173 ft. lbs. (235 Nm) on gray colored nuts. Front wheel. Torque the nuts to 100 ft. lbs. (140 Nm).

Jul 27, 2009 | 2004 Oldsmobile Alero

1 Answer

Front wheel bearings


If the hub is not bolted on then all you have to do is get a big pair of channel locks and get a good grip on the hub and pry it off. The wheel bearing will be directly under the hub and have a cotter pin installed in for safety. I hope this helps. Don,t forget to rate my answer, thanks.

Feb 28, 2009 | 1995 Toyota 4Runner

Not finding what you are looking for?
2005 Chevrolet Uplander Logo

Related Topics:

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...