Question about Chevrolet Silverado

1 Answer

I have a 79 chevy 4x4 and i was wondering what the gears meant on the 4x4 shifter and what is the normal running gear for just normal drivng

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 266 Answers

SHIFTER SHOULD BE 4 HI 4 LOW 2HI 2LOW NORMAL DRIVING RUN IT IN 2 HI

Posted on Oct 13, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I adjust 4x4 linkage on a manual floor shifter


manual controls are very reliable, like in or out.If the shifter is hard moving? use some oil.Gear clash grinding first to reverse.counter shaft nose.If there is no high or low 4x4 Good luck.

Feb 22, 2015 | Cars & Trucks

1 Answer

Chevy cavalier gear shifter


if it is s manual box remove the gear lever tower from the top of the box and see what damage was done to the bottom of lever and/or lever pivot pin in the tower. Remember normal gear boxes require a gentle shift to allow the syncro rings to work properly and if you want to do racing changes get yourself a specially built box.

Jan 02, 2014 | Cars & Trucks

1 Answer

Shifter went limp now cant shift out of gear feels like broke inside.. shifter knob does a circle motion now cant even move shifter knob like i normally would.. i had to pop clutch to get truck started...


you have to know if the problem is inside transmission or outside
first under truck unplug shifter cable then try to move the manual lever of transmission near the pan but have hand brake on so the truck won't run over you.
if the problem is inside the transmission could be the parking pawl nut to manual shaft too much end play
if it outside transmission could be trans, cable or linkage
hope it helps

Oct 15, 2013 | Chevrolet Blazer Cars & Trucks

1 Answer

1993 chevy k1500 transmission problem


Do you mean start the car in drive? if so that problem is inhibitor switch. Other shift problems can be caused by TPS (throttle posistion sensor) if applicable

Oct 05, 2012 | 1993 Chevrolet K1500

1 Answer

93 Chevy, gear shift **** between 2nd and 3rd


Remove the fluid - get a good flash light - get a very long screw driver - put the screw driver into the drain hole and force the transmission out of gear. Then remove the Transmission and replace or repair. Cheaper to replace. You bent the forks on the shift mechanism.

Apr 02, 2010 | 1993 Chevrolet C/K 2500

2 Answers

HOW TO USE 4 WHEEL 1980 CHEVY K20 PICKUP


have truck running,,put shifter in neutral,,shift into high lock 4x4,then put truck into gear,,u can shift from high lock to high gear,,from two wheel to four wheel,,in high only,,if u want to shift transfer case in low,,u have to put truck in ,,neutral,,first,,

Feb 06, 2010 | Chevrolet K2500 Cars & Trucks

1 Answer

1999 k2500 4x4 5 speed started grinding only when


If it is noisy only in third, then third is where the problem is, cluster gear and/or mainshaft gear. Rule of thumb, if it is noisy in only one forward gear, then that gear is where the problem is.

Sep 11, 2009 | 1999 Chevrolet C/K 2500

1 Answer

My 96 chevy blazer 4wd will not work?


check clutch slave cylinder and or adjustment

Jan 16, 2009 | 1999 Chevrolet Blazer

2 Answers

1988 suzuki samurai WONT MOVE


First thing just try to push or pull the 4x4 lever if you get it to move and it feels like it went into some gear try to drive the truck.If this works look on the shifter for the 4x4 and put it in 2 wheel drive (H2 is two wheel drive,H4 is 4x4 high,and L4 is 4x4 low range).Make sure you have the clutch depresed when you try to move the 4x4 lever.If you try this stuff with no fix try and look for clutch adjustment on the transmision you may need to adjust it or your clutch is bad.

Aug 30, 2008 | 1988 Suzuki Samurai

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...