Question about 2000 Mitsubishi Mirage
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
go to your parts suppler and ask for a H4 globe pop your bonnet and remove the plug on the back of your head light then remove the rubber boot paying attention to which way it cam off then you will find a spring clip unclip it but be careful not to damage its anchor point. remove old globe an throw away take new globe out of box DO NOT TOTCH THE GLASS OF THE GLOB AS IT WILL CAUSE THE GLOBE TO BLOW STAAIGHT AWAY AFTER FITTING IT handle the globe by the metle bass and fit it, refit spring clip and rubber boot fit the plugf and check the operation of the light
bingo you are done have a nice day
Posted on Dec 21, 2008
You shouldnt have to pull the whole lens assembly.On the back of the lens assembly(inside engine compartment)you should find what looks like a big round nut where the wires go in.unscrew that nut and your headlight should come out and you can insert the new one.Its a halogen bulb.
Posted on Mar 04, 2009
There is pressure...you have to remove the rear seat cushion,then remove the service cover and then detach the fuel pump harness connector.Start the car and allow it to run until the engine stalls.Turn the key to off position.Then disconnect the negative battery cable, attach the fuel pump connector, and install the access cover. Now place shop rags or towels around the fitting that is being disconnected. Loosen the filter feed pipe flare nut on the bottom of the filter.Seperate the flare nut from the filter. If equiped, remove and discard the gakets. remove the mounting bolts and remove the filter.if necessary remove the filter bracket. To install: install the filter to it's bracket only finger tight. Make sure the flow arrow is in the right direction. Make sure new O rings are installed prior to installation. Insert the filter feed pipe to the lower connection of the filter and manually screw in the main pipe's fare nut. While holding the fuel filter nut with a back-up wrench, tighten the banjo bolt to 22 ft pounds and tighten the flare nut to 25 with a back-up wrench on the nut. tighten the filter mounting bolts to 10 ft. pounds. Connect negative battery cable. turn key on to pressurize the fuel system and check for leaks. If repairs on the fuel system are needed remember to release the pressure before opening the fuel system. Hope this helps. Good luck!
Posted on Mar 15, 2009
SOURCE: replace headlight bulb
Actually there are two little black tabs on top of each headlight housing and you simply have to pull them up to release the whole headlamp.
Then follow the rest of emissionwiz's solution.
Posted on May 28, 2009
At least on the driver side, there really is no reason to remove the entire headlight assembly. I was able to swap out the bulb fairly easily but simply removing the dust cap, popping the connector off the bulb, and then undo the clip holding the bulb in place. The just reverse order to install the new bulb. Took about 3 minutes.
Posted on Dec 13, 2009
Tips for a great answer:
Open the Galant's hood and locate the headlight cover -- roughly 3-inch wide circular piece of plastic -- behind the headlight bulb intended for replacement. Turn this cover clockwise to unlock it and pull it from the headlight assembly, exposing the headlight socket below it.
Hold the rear of the headlight socket and turn it counterclockwise to unlock it. Pull the headlight socket and bulb from the headlight assembly.
Grab the bulb and pull it from the socket with a slight wiggling motion.
Pick up the new 9003 headlight bulb using a clean, lint-free cloth and line up its prong with the slots in the socket. Never tough the bulb with your bare hands, as the oils left by your hands can cause the bulb to burn out prematurely.
Slide the socket and new bulb into the headlight assembly and turn the socket clockwise to lock it into place.
Place the plastic cover behind the bulb and turn it counterclockwise to lock it into place.
Repeat Steps 1 through 7 for the headlight bulb on the other side of the Galant, if needed. Close the Galant's hood.
Read more: How to Put in a Headlight Bulb on a 2000 Mitsubishi Galant ' eHow.com http://www.ehow.com/how_8210819_put-bulb-2000-mitsubishi-galant.html#ixzz27iQwCdOe
Close the Galant's hood.
Sep 27, 2012 | 2000 Mitsubishi Galant
Aug 01, 2012 | 1997 Mitsubishi Mirage
Feb 16, 2011 | 2000 Mitsubishi Mirage
Jul 29, 2010 | 2000 Mitsubishi Montero
Oct 03, 2009 | 1999 Mitsubishi Mirage
Aug 26, 2009 | 1999 Mitsubishi Mirage
Jul 14, 2009 | 2000 Mitsubishi Montero
Jun 20, 2009 | 1999 Mitsubishi Mirage
748 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: