Question about 2001 Chevrolet Cavalier

1 Answer

Remove and replace engine does it come out top or botom?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 2,309 Answers

You can remove the engine from the top. remove the hood for easier access, get yoursellf a manual and follow it , you will need access to both upper and lower engine for removal

Posted on Oct 13, 2010

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to remove 2004 Jeep Liberty engine computer

I posted the instructions below with a picture. Now I'm not sure if you are replacing but guessing you are. Just to let you know this computer type is famous for going bad because they have a chip on top of another chip and the botom computer chip goes bad. They are sometimes hard to find as well. If you are looking for a used one, in most cases they are bad too because of the chip situation. In any case each computer goes by number and it has to be programmed (flashed) for your vehicle identification number. I hope this helps and good luck


Oct 30, 2011 | 2004 Jeep Liberty

2 Answers

I need to replace my 95 chevy corsica transmission do i have to take out the engine

the trans is removed through the bottom with the engine left in

Jul 27, 2011 | 1995 Chevrolet Corsica

1 Answer


the rqad hoses are dont from top and botom
you do not need to remove the rad fan to repair the hoses
you need to jack up the car and remove the bely pan if the lower rad hose goes to **** and fix it from under side if top hose goes then it ir replaced from thr top
good luck and arent you glad you bought a beemer

Mar 26, 2010 | 1999 BMW 5 Series

1 Answer

My horn will not work and my driver airbag light is on. 2005 Saturn ION 2

sounds like some loose conectors remove the columb cover
there are 2 - 4 screws on the botom of it they are usually star or philips screws cover should fall off or may requier a tug check the wiring conectors top and botom just lift top cover up it will flex remember to keep the ignition turned off

Jan 28, 2010 | 2005 Saturn ION

1 Answer

Can I remove the (auto) transmission seperatly, without removing the engine with it. If so, remove thru top or bottom?

remove through botom at side
there is a trick and you do need an engine suport frame

it is just a simple tilt and slide it is posable and it is tight if i remember corectly you need to drop the engine mount on front of engine to allow for angle leave fire wall and hanger by rad conected they will flex

Jan 17, 2010 | 2000 Hyundai Accent

2 Answers

Looking to pull the engine out of 95 camaro 3.4 with manual tranny does it come out the bottom or the top?

You can pull that engine out of the top. It is easier to drop the engine cradle, remove the drive shaft firs, and wiring harness. There should be four bolts located on the cradle at four locations. Lower the cradle with 2 jacks one on each side, lift the car and slide cradle from under the car. i have done this with an Intrige and was easier than trying to pull from the top.

Jan 02, 2010 | 1995 Chevrolet Camaro

1 Answer

How much work and what is all involved in replaceing the piston rings for a 1991 ford probe?

you have to remove the top half of the engine then remove the bottom of the engine then you can un bolt the botom of the piston to slide it all the way up then you can take the rings of and add the newones

Oct 29, 2009 | 1991 Ford Probe

2 Answers

Whats easiest way to remove and replace engine in a 1996 ford taurus from the botom or out threw the top

depending on how your set-up makes all the difference. if you are doing it in the drive way out the top is the best. if you have a shop and a lift then top or bottom is almost the same. coming out the top is a little harder if you haven't do it before. so if you have a lift and equipment the bottom is best.

Oct 25, 2009 | 1996 Ford Taurus

1 Answer

Replace power antenna

its held in by the bracket on the botom of it and also the chrome nut arount the top of it... remove the nut from the top and the bolts from the base support bracket and then remove the antenna and power wires.. when installing replacement antenna secure the top nut first. then bolt base and reconnect antenna wire and power plug

Feb 24, 2009 | 1998 Cadillac DeVille

1 Answer

Trying to get the trans out with out removing the motor

with the tranny mount removed lower the back of the engine and tranny as far as you can.......from the back of the tranny you should be able to see the two top bolts and a series of extensions will allow you to get them loosened

Dec 22, 2008 | 1987 Chevrolet Camaro

Not finding what you are looking for?
2001 Chevrolet Cavalier Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides