Question about 2001 Honda Civic

1 Answer

Ecu wiring connectors

Procedure on depinning wiring harness connectors on 2001-2005 honda civics

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 50 Answers

Hi there. Honda employs a system called TTS (Total Terminal Security) and it's what gives Honda a great name when it comes to reliable electrics and electronics - their electrical connections and pin conections are truely fabulous. You need to look very carefully at each plug, firstly removing the small rubber grommet and then use a very small watch type screwdriver to bend back the small metal tabs that retain the pin connector in place. It's fiddly work, but it can be done. Best regards. Scottech.

Posted on Jun 17, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

D16y8


The d16y8 is used in the 1996 to 2000 Civic EX, as well as the 1996 and 1997 Del Sol. Both harnesses and ECUs will work from either.

Apr 18, 2014 | 1996 Honda Civic del Sol

1 Answer

1996 Honda Civic driver door window wire harness connector is bad


Try a wreckers that specialises in wrecking Honda for the harness.

Feb 22, 2014 | 1996 Honda Civic

1 Answer

Honda civic eg8 ,no spark in distrubitor


so the wires from the dist. cap to the plugs are ran wrong? best way to get it right is to lay them out shortest to longest and go from there. Or is it an electronic dist. and its powered and ran from the wiring harness and ecu? because in that case, if you put in an aftermarket piece, you may need to flash over the ecu or get a piggy back so it and the dist. can talk to each other. hope that helps some.

Apr 20, 2013 | 1995 Honda Civic

2 Answers

The 1999-2000 Model Honda Civic uses an OBD2B connector for the ecu. I am changing my ecu to a programmable OBD1 PO6 or P28 ecu. Therefore i would need a jumper harness from OBD2B to OBD1. I already have...


The reason you can't find the connector you want = it's illegal to replace the OBD2 PCM with a OBD1 controller for any vehicle registered for the street. This is a felony on the Federal level and also several States. If you are only using the car for the track, it's ok. You may try a raceing supplier like Summit, etc. to find one.

May 11, 2011 | 1999 Honda Civic

1 Answer

I need to replace my starter on my 1993 honda civic... Help?


  1. Disconnect the negative battery terminal and the starter motor cable at the positive terminal.
  2. Remove the engine wire harness from the harness clip on the starter motor
  3. Disconnect the cable from the B terminal on the solenoid, and the BLK/WHT wire from the S terminal.
  4. Remove the starter motor by loosening the two attaching bolts.
  5. To install, reverse the removal procedures: re-position the starter in place, replace bolts, tighten the starter-to-engine bolts to 32 ft. lbs. (45 Nm).
  6. Make sure that all wires are securely connected.

Mar 20, 2010 | 1993 Honda Civic 4 Door

2 Answers

Just a question


The swap is easy but too much to post here. I will fit into any civic 89-00 with the right aftermarket mounts from hasport or just go to ebay. The engine harness can be purchased at a local juck yard if you don't have a harness with 4 injectors. I you have only two injectors then the harness will need to be modified with vtec wiring and ad the other 2 injectors. Any 90-93 integra axles will fit as long as you use the halfshft. Must be manual. and use a modified shif linkage from ebay. Youmust take off the caps behind the civics hubs. Use a PWO or PR3 ECU. Good luck.

Jan 28, 2009 | 1989 Honda Civic

1 Answer

Installing universal Oxygen sensor


here is the 97 civic electrical diagrams. after you download and unzip the file, try 17252.pdf.

Oct 11, 2008 | 1996 Honda Civic

1 Answer

Honda civic hatchback


you have to change wiring harnesses and ecu then recheck timing u should be set

Sep 21, 2008 | 1990 Honda Civic

1 Answer

I have 1991 civic shell, swap to 1994 del so jdm ingine,


Go to honda-tech.com Register and you can download the manual that matches your engine. Chances are that you do not need all ten wires. Russ (camieng on eBay)

Jul 29, 2008 | 1991 Honda Civic

Not finding what you are looking for?
2001 Honda Civic Logo

Related Topics:

162 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

64034 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...