Question about Ford F-150

1 Answer

I need an exploded view of steering wheel showing ignition switch,actuator parts

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 266 Answers

GO TO YOUR LOCAL DEALER PARTS DEPARTMENT AND ASK THEM TO PRINT IT OUT FOR YOU

Posted on Oct 13, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the headlight relay switch located on a 1999 oldsmobile intrigue


Looking at my Olds Intrigue 1998 Service Manual (Volume 1 of 3), I believe Oldsmobile calls what you describe as either the "Headlamp Switch Turn Signal Lever" (part #1 on the exploded view), or the "Headlamp and Turn Signal Switch" (part #2 on the exploded diagram on page 8-53 of the first volume of the Service Manual). I had to order a "turn signal switch" to get my horn to work from the steering wheel (it worked from the remote), and I'm thinking that your part is also part of the "turn signal switch."

It's on top of the steering column (under the shroud-like plastic), right behind the steering wheel from where you sit in the car. It takes a mechanic about 1.5 hours to replace it and it's tough for you to do if you don't own the right tools and know how to get to it. (I never got it figured out.)

If the white printing on the turn signal lever is a bit worn, it's a good clue that what it controls has had wear, and you may need to replace it soon anyway.. You also might check with the store you are getting the part from to make sure.

Best wishes!

Feb 25, 2015 | 1999 Oldsmobile Intrigue

2 Answers

Runs but only when applying pressure to the steering wheel


sound like loose wires to the ignition switch in the steering column. just remove steering column shroud and lower the steering column check the ignition switch wires.first disconnect negative battery cable before working on ignition switch. either switch wires loosen or switch could be bad.

Jul 29, 2013 | 1990 Ford F150

1 Answer

What is the procedure to changing an keyed ignition lock?


Hi there,

Removal

Disconnect the negative battery cable with the proper size wrench and place away from the battery.
Insert the key into the ignition lock cylinder and turn the key to the run position.
Remove the steering column cover on a tilt steering wheel model by pressing the upper and lower section of the cover together and pulling free from the mounting plate. Remove the steering column covers on a non tilt steering wheel model by using a Philips screwdriver and unscrewing the mounting screws.
Disconnect the electrical connector from the ignition switch by lifting up on the release tab and pulling.
Press the ignition switch actuator pin by pushing a small screw driver into the key lock cylinder, while doing this pull the ignition switch out of the ignition switch housing.

Installation

Insert the new key into the new ignition switch and turn the key to the run position. Insert the new ignition switch into the ignition switch housing. Wiggle the switch back and forth until the actuator pin mounting hole is aligned and falls into place.
Install the electrical connector back into the connector housing by pressing it in with your hands.
Place the steering column covers back onto the non tilt steering wheel and insert mounting screws. Tighten screws using a Philips screwdriver. Place the steering column covers over the tilt steering wheel and press the upper and lower portion together to snap covers back into the mounting plate.
Pull on the ignition key to ensure switch is locked into place. Turn key to the "off" position and remove the key. Insert the key and start the vehicle.

Hope these help.

Jan 28, 2011 | 1992 Ford Crown Victoria

1 Answer

How to change a ignition switch on a 1990 Z24 cavalier and a diagramof what to look for


Ignition Switch REMOVAL & INSTALLATION 1982–91 Vehicles The switch is located on the steering column and is completely inaccessible without first lowering the steering column. The switch is actuated by a rod and rack assembly. A gear on the end of the lock cylinder engages the toothed upper end of the rod.
  1. Lower the steering column; be sure to properly support it.
  2. Put the switch in the OFF-UNLOCKED position. With the cylinder removed, the rod is in OFF-UNLOCKED position when it is in the next to the uppermost detent.
  3. Unfasten the two switch screws and remove the switch assembly. Fig. 1: Removal and installation of the ignition switch and related steering column components — 1990 vehicle shown 87958059.gif
    Fig. 2: Exploded view of a steering column including the ignition switch — 1990 vehicle with standard column shown 87958060.gif
    Fig. 3: Exploded view of the steering column including the ignition switch — 1990 vehicle with tilt column shown 87958061.gif
    To install:
  4. Before installing, move the new switch slider (standard columns with automatic transaxle) to the extreme left position. Move the switch slider (standard columns with manual transaxle) to the extreme left position. Move the slider (adjustable columns with automatic transaxle) to the extreme right position and then move the slider one detent to the left (off lock). Move the slider (adjustable columns with manual transaxle) to the extreme right position.
  5. Install the activating rod into the switch and assemble the switch on the column. Tighten the mounting screws. Use only the specified screws, since overlength screws could impair the collapsibility of the column.
  6. Reinstall the steering column.

Sep 01, 2010 | Chevrolet Cavalier Cars & Trucks

1 Answer

CHANGE IGNITION SWITCH ON AUTOMATIC GMC SIERRA WITH 5.7LITER ENGINE


Removal & Installation


0f0e09a.gif
Exploded view of the ignition and key alarm switch

  1. Remove the column shroud halves.
  2. Remove the column-to-dash attaching bolts and slowly lower the steering column, making sure that it is supported.
  3. Remove the multi function switch if necessary.
  4. Remove the key alarm switch, if equipped by gently prying the alarm switch retaining clip with a small screwdriver. Rotate the alarm switch 1/4 in. turn and remove.
WARNING Extreme care is necessary to prevent damage to the collapsible column.

  1. Make sure that the switch is in the Lock position. If the lock cylinder is out, pull the switch rod up to the stop, then go down one detent.
  2. Disconnect the actuating rod from the switch.
  3. Remove the two screws and the switch.
To install:
  1. Before installation, make sure the switch is in the Lock position.
  2. Attach the actuating rod to the switch.
  3. Install the switch using the original screws. Tighten the screws to 12 inch. lbs. (1.4 Nm).
  4. Install the key alarm switch, if equipped . Make sure the retaining clip is parallel to the lock cylinder. Rotate the alarm switch 1/4 in. turn until locked in place.
  5. Install the multi function switch if removed.
CAUTION Use of screws that are too long could prevent the column from collapsing on impact.

  1. Replace the column. Tighten the nuts to 22 ft. lbs. (29 Nm); the bolts to 20 ft. lbs. (27 Nm).
  2. Install the column shroud halves.


ae03a0b.gif
Exploded view of the alarm switch removal

May 04, 2010 | 1998 GMC Sierra

2 Answers

1985 ford F150: Turned key to start my truck, and felt something go "crunch". I removed the steering wheel and the lock mechanism in the steering column. All looks fine. Do you have any idea what could...


It may be the 'actuator'. It is a rod that connects the lock cylinder to the ignition switch on the tilt wheel units. It is made of aluminum and often breaks as things become worn.

Jun 23, 2009 | Ford F-150 Cars & Trucks

1 Answer

1994 s-10 replaced ignition actuator gear rack


if you goto any auto parts store you can get a repair manual for your vehical. but i think that the neautral safty switch is no hooked up right.

Mar 20, 2009 | 1994 Chevrolet S-10

2 Answers

For the past 3 days i have had to shake the strering wheel to get the truck to crank also moving the sterring wheel up and down worked sometimes too. so today when i went to go crank it . the truck where...


There should be a pin hole under the lock or on side of where the key goes . push a sewing pin in it and the key has to be in the ignition and released to pull lock out with the key in . Try that

Jan 25, 2009 | 1989 Ford F 150

2 Answers

How do i replace the key cylinder ignition on the 1991 sunbird le


This (plate) is held in place with a snap ring.You will need a special press to remove it and also a steering wheel puller to access the ignition lock cylinder.The actual switch is located on top of the steering column above the brake pedal. It is actuated with a rod from the ignition lock cylinder.

Jan 10, 2009 | 1991 Pontiac Sunbird

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

112 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...