Question about 2002 Chrysler 300M

1 Answer

Keyless entry i have a 2002 300m... my question is where the heck is the keyless entry modual on these cars??

Posted by on

  • copatrick Jun 01, 2008

    thanx for the fast response, but i have looked there and all i find is the junction box and the BCM and the daytime running light module... so is it contained within the BCM?.... let me explain why i ask.. my keyless entry does not work, and when i start the car sometimes it turns off right away and does this 6 times and then locks up... then i have to disconect the batery for a while... or the car will start and all the warning lights remain on and the guages do not work and i get a message "no buss" ... so it seems like my security system is partly engaging like its not reconsizing my key... i have replaced the junction block and the BCM and the problem remains... thanx for any help u can provide...



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 625 Answers

The Remote Keyless Entry (RKE) Module is located between the Junction Block and Body Control Module.
THIS CAR COME WITH 4 DIFERENT ENGINES SAME ENGINE SIZE BUT DIFERENT INJECTION SYSTEM THIS information is for a 3.5 vin (G ) the engine vin code is on the vehicle identification number and is the 8th digit from left to right

Posted on Jun 01, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do I reset keyless door entry that is in lock out mode

Viper Keyless Entry Systems
Viper is the industry leader in keyless entry systems. Add the convenience of keylessentry to virtually any vehicle - even vehicles without power door locks!

Alarms, Remote Car Starters, Keyless Entry & Locks - JC ... > Audio, Video & Electronics
20 out of 32 products in Alarms, Remote Car Starters, Keyless Entry & Locks ..... ofKeyless Entry & Car Alarms allow you to lock and unlock power door locks.
How to program your keyless entry keypad - Ford Owner Motor CompanyDiscover how to lock and unlock your doors and how to program memory settings that will adjust seats & mirrors for each driver.SecuriCode™ Keyless Entry Keypad - Ford Motor CompanyLearn how to set a 5 digit SecuriCode on the Ford keyless entry keypad. ... Sign out. Register/Sign In · Your Vehicle. Service & Maintenance. Service & .... vehicle's SecuriCode keypad to lock and unlock your doors without having to use a key. ... Thekeypad will go into an anti-scan mode if you enter the wrong code seven ...How Programming Your Keyless Entry Can Make ... - Ford Life

Jan 08, 2016 | Cars & Trucks

2 Answers

I am looking for the keyless entry code for my 2002 sable and the one on the card in the book does not work

Sounds like a pervious owner must have changed it. Try back tracking the owners and see if you can get the code.

Jul 21, 2010 | 2002 Mercury Sable

1 Answer

How do i reprogram electronic door locks

Programming Electronic Door Lock Control System NOTE: The electronic door lock control processor (14B001) erases all previous keyless entry remote transmitter (15K601) from memory when the keyless entry remote transmitters are programmed or reprogrammed. The electronic door lock control processor can store up to four keyless entry remote transmitters in memory.

  • To program (or reprogram) keyless entry remote transmitter into the electronic door lock control processor, perform the following steps:
  1. Turn ignition switch to the RUN position and momentarily short the two terminals of the program connector taped to the wire assembly and located behind the glove compartment. All doors should lock and then unlock. Remove shorting pin.
  1. Press any button on keyless entry remote transmitter. All doors should lock and then unlock to verify the keyless entry remote transmitter has been programmed. If door locks do not respond, press button again (up to three times maximum with the same keyless entry remote transmitter).
  1. Repeat the above step to program additional keyless entry remote transmitters into the electronic door lock control processor (up to four keyless entry remote transmitters maximum).
  1. Turn ignition switch OFF. All doors should lock and then unlock.
  1. Check operation.

Jun 05, 2010 | 1997 Ford Windstar

2 Answers

Looking for installation manual for a prostart ct-3100.I would like to install it in a 2000 gmc jimmy

here is the information you requested, good luck on the jimmy, you will also need a passlock 2 bypass modual and a door lock polarity inverter, let me know if you need them as I stock these items

Dec 10, 2009 | 2000 GMC Jimmy

3 Answers

Passenger & rear power windows not working

First to keep with the basics, make sure you haven't inadvertantly hit the safety lockout button on your drivers side control panel. Then pop out or unscrew the switch from it's holder and check with a test light if the power is being ditributed to the other windows, if not you'll need a new door control modual and you'll have to take it to the dealer so they can code it and activate it according to your keyless entry system.This is probably covered under waranty and or recall. Thank you, Dana

Sep 10, 2009 | 2006 Lexus Rx 330

1 Answer

What extra components will I need to install a rs 1100 bulldog remote start keyless entry system on my 05 Dodge Caravan?

Transponder bypass modual $60 I have them in stock if you need one, and if you are hooking up the door locks you will also need
2 relays and 2 resistors $20 they are instock aswell

Sep 08, 2009 | 2005 Dodge Caravan

1 Answer

I need to know where to find the computer module on an F-350. (I am looking for the factory remote lock code which is supposed to be printed on the computer module.) There is a small black box underneath...

your looking for the keyless entry modual, it is undr the dash on the drivers side- if you can't find it take it to your local ford dealer, they can pull the code out of the computer with a scan tool

May 16, 2009 | 2004 Ford F350

1 Answer

I need to find the door lock code for my 2003 ford windstar

2 ways
look unde the dash driver's side for the keyless entry modual, there is a sticker on it that has the code on there.
or take it to your local ford dealer and have them pull the code with the scan tool

May 15, 2009 | 2003 Ford Windstar

1 Answer

Keyless entry on honda civic 2006 not working

The keyless entry is designed to work with the doors closed (closed - not locked). If the door ajar sensor thinks the door is open the keyless entry is disabled. When you manually lock the door it might tighten the door just enough to activate the keyless entry. I would try slamming all the doors closed and then see if the keyless entry works. If it still wont work have the wiring checked on the front door lock.

May 12, 2009 | 2006 Honda Civic Hybrid

Not finding what you are looking for?
2002 Chrysler 300M Logo

589 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts


Level 3 Expert

78289 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides