Question about Ford Taurus

1 Answer

I'm pulling a motor 3.0 v-6 2000 taurus is there a diagram to help me my concern is clearance at front of motor where pullys are

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 8,140 Answers

Here are complete instructions from autozone.com. It doesn't show the clearance, but it does tell you what has to come off to clear.

  1. Disconnect the negative battery cable.
  2. Drain the engine oil.
  3. Drain the cooling system.
  4. Recover the A/C refrigerant.
  5. On the 3.0L (VIN S) engine, remove or disconnect the following:

    Windshield wipers Cowl extension Emission vacuum control connector at the right side of the dash panel Hood Steering column pinch bolt Mass Airflow (MAF) sensor connector Intake Air Temperature (IAT) sensor Air cleaner assembly Idle Air Control (IAC) valve connector Throttle Position (TP) sensor connector Fuel lines Intake manifold vacuum hoses Ground straps Powertrain Control Module (PCM) connector Engine control sensor wiring harness connectors from the bracket located at the top of the transaxle Evaporative emission canister purge valve connector Crankcase vent hose Accelerator cable Cruise control actuator Shift cable and lever Secondary air injection pump relay connector Main emission vacuum control connector near the fan shroud Radiator hoses Heater hoses Transaxle oil cooler lines Power steering return hose Alternator wiring harness connectors A/C compressor lines A/C pressure cutoff switch, if equipped Front wheels Stabilizer bar links Lower ball joints Outer tie rod ends Halfshafts Radiator splash shield Heated Oxygen (HO 2 S) sensors Dual converter Y-pipe Power steering pressure switch connector Power steering pressure hose
  6. Support the powertrain from below and remove the subframe bolts.

I'm pulling a motor 3.0 - 6c74736.gif Fig. Throttle and cruise control cables-2001-04 3.0L (VIN U) engine shown

1f3d2f9.gif Fig. Throttle Position (TP) sensor and Intake Air Control (IAC) valve connectors-2001-04 3.0L (VIN U) engine shown

1c8414a.gif Fig. Support the powertrain when removing the subframe bolts
  1. Raise the vehicle away from the powertrain.
  2. Attach an engine hoist to the powertrain.
  3. Remove the left, right, and rear powertrain support insulators and lift the powertrain away from the subframe.
  4. Support the transaxle from below.
  5. Remove or disconnect the following:

    Starter motor Torque converter Transaxle flange bolts
    Separate the engine from the transaxle.

Posted on Oct 13, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1993 taurus 3.2 ltr. engine with no idler or tentioner pulley. how do i get belt loose so i can install alternator.


there is a tensioner pully on the front of the motor you can get a wrench on and it will make it easy to put the belt on.

Aug 09, 2012 | 1993 Ford Taurus

2 Answers

Is it possible to get a diagram of the crank sensor for the 2004 hyundai sonata


Hi, in both engines the crank sensor is at the back of the engine by the transmission. The sensor is #10 in the diagram below and looks like the picture included.
jturcotte_1640.gif

4-cylinder crank sensor:
jturcotte_487.jpg

6-cylinder crank sensor:
jturcotte_488.jpg

May 06, 2011 | Hyundai Motor 2004 Sonata

1 Answer

We took the serpentine belt off our 03 ford taurus and there is no diagram to put it back on


There should be a diagram under the hood.
Look at the pully's, those with grooves get that side of the belt and those without get the other side, work your way around the outside, doing the water pump last

Mar 06, 2010 | 2003 Ford Taurus

2 Answers

My serpintine fan belt came off as I started the motor; w/o air conditioner, but it does have power steering- the new belt seems to be too long, even though I had brought in the old one and followed the...


All it takes is for one part of the belt to be in the wrong position for it to appear to be too long. Check the diagram again. There is often a diagram in the owner manual as well as under the hood.

Oct 15, 2009 | 1989 Chevrolet G20

2 Answers

Pully wont spin after waterpump replacement


pull the water pump back off and see if something got wedged in there. your son might have dropped something in there before he put it on.

Apr 05, 2009 | 2003 Ford Taurus

2 Answers

Misfire on cylinder 6 on a 2002 ford escape 3.0 6 cylinder DOHC


the back side is from front(passenger side) of engine 1,2,3
front side is 4,5,6

Mar 17, 2009 | 2000 Ford Taurus

1 Answer

97 ford taurus power steering pulley


pull the pully back off ,clean the shaft with emery cloth and also the the shaft hole in the pully then grease it up and try it again

Mar 14, 2009 | 1997 Ford Taurus

2 Answers

1999 dodge caravan


There is a tension pully located under the alternator. It has a bolt head in the middle of it. Place a long box end wrench on it and pull it towards you. The tensioner will move forward. first put the belt on the pullies properly. (see diagram placed at left side of the hood release). Then leave the belt off the pully that is located just under the motor mount. Pull back on the wrench that is placed on the tensioner as you at the same time place the belt onto the pully under the motor mount. Done. Remember that the tentioner may need to be replaced also. It might be a good idea to do that since that is the usual reason the belts jump off. Just a couple bolts with that and done. It is not expensive.

Sep 28, 2008 | 1999 Dodge Caravan

2 Answers

Serpentine belt


hello two things you can do under your hood look very good ford usually has a routing diagram mounted on the top support of your radiator or off to the side it will be a pitcher of a front of a motor with pullys should show you with and without ac routing if not dont panic go to part store like auto zone get your self a haynes manuel that covers your year car the serpitine routine should be in there for your motor goodluck please rate

Aug 19, 2008 | 2004 Ford Taurus

1 Answer

Front motor mount


Place a block under motor, jack the motor up until you have clearance to remove top bolt.

Jul 24, 2008 | 1993 Ford Taurus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,591 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...