Question about 2003 Hyundai Tiburon

1 Answer

I NEED TO KNOW THE EXACT LOCATION OF WHERE THE CRANKSHAFT POSITION SENSOR IS LOCATED ANY HELP WILL BE GREATLY APPRECIATED THANKS?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 3 Answers

Remove negative battery cable. Remove heat shield from starter. Remove battery cable from starter lug and single wire connector to starter solenoid. Remove starter. Above starter is CRANKSHAFT POSITION SENSOR. Disconnect sensor connector right below ignition coil assemble from top of engine. Slide sensor connector out of U-shaped bracket. Loosen 10mm bolt securing sensor. Lubricate new sensor O-ring with vaseline and install. Reverse procedure to finish job. I just did the job on my 03 Tibby 2.7liter today. Note: Make sure you press the new sensor in by hand and be sure it is seated all the way before you tighten the 10mm bolt, otherwise the sensor mounting tab make distort and crack and the sensor may not be in all the way. Good luck!

Posted on Oct 18, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

97 chevy 5.7 crank sensor location


The CKP (Crankshaft Position) sensor is located in the front engine cover and is perpendicular to the crankshaft target wheel. The air gap between the sensor and the wheel is preset and not adjustable. The target wheel has three slots 60 degress apart and is keyed to the crankshaft. As the target wheel rotates, the slots passing by the sensor create a change in the magnetic field of the sensor which results in an induced voltage pulse. One revolution of the crankshaft results in three pulses (3x signal). Based on these pulses, the VCM is able to determine crankshaft position and engine speed. The VCM then activates the fuel injector and provides a spark to the Distributor. The relation between the crankshaft position sensor and the target wheel is crucial. The sensor must be exactly perpendicular to the target wheel with the correct air gap.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Feb 15, 2012 | Cars & Trucks

1 Answer

Need to know where the crank shaft sensor is located.


The Crankshaft Position Sensor is located under hood, center, rear engine area, mounted onpassenger side rear of cylinder head.

9_20_2011_5_58_25_pm.jpg

Fig. 2: View of the Crankshaft Position Sensor (CKP) location-2.2L engines


9_20_2011_5_58_48_pm.jpg

Fig. 3: The Crankshaft Position (CKP) sensor location-2.3L/2.4L engines


Hope this helps (remember to rate this free answer).

Mar 24, 2011 | 1997 Pontiac Sunfire

1 Answer

Jsut want to know where crankshaft position sensor


Hi!!

here are illustrations of the CKP (crankshaft position) sensor in 2.3L and 3.0L.

Note: In the bottom of the 2.3L drawing says Trottle Position (TP) Sensor, this is wrong, It should say CKP Sensor.


2.3L Engine


The Crankshaft Position (CKP) sensor is located to the left of the crankshaft pulley.

0996b43f80202990.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Crankshaft Position (CKP) sensor location-2.3L engine


3.0L Engine


The Crankshaft Position (CKP) sensor is located just behind the crankshaft pulley on engine block.

0996b43f8020299e.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Crankshaft Position (CKP) sensor location-3.0L engine

The cost of the sensor is $23 bucks at AutoZone.

If helpful, click below

Apr 15, 2010 | 2002 Ford Escape

1 Answer

My mechanic is having trouble locating the crankshaft position sensor on my 2005 hyundai sonata does anyone know where it is located?


hi,
i have attached the image, showing the position of crankshaft position sensor.hope its helpful for you. Please rate my solution as helpful.have a great day.c9acd5a.jpg

Feb 21, 2010 | 2000 Hyundai Sonata

1 Answer

Crankshft position sensor


Hi I can help but need to know what engine you have.

Oct 22, 2009 | 1999 Jeep Grand Cherokee

1 Answer

2000 Nissan Sentra Crankshaft Position and Replacement


Go to dealership they will give a diagram to locate every single one. I replace them on my daughter car. I believe there were three sensors. I exactly know what you are talking about. I had a hard time locating the back one right above the drive shaft on driver side.

Aug 27, 2009 | 2000 Nissan Sentra

3 Answers

Crankshaft sensor


2-0L-2.4L I-4 crankshaft sensor mounts to the engine block, behind the alternator, just above the oil filter. 2.5L V-6 crankshaft sensor mounts to transaxle just below the distributor.

May 07, 2009 | 1998 Dodge Stratus

Not finding what you are looking for?
2003 Hyundai Tiburon Logo

539 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...