Question about 2002 Pontiac Montana

Open Question

What is the torque on the front axle nut, of a 2002 Pontiac Montana, two wheel drive.

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 Pontiac wave torque settings for wheel bearing replacement


If it is the drive axle hub nut you are reffering to, the torque spec is 221 ft lbs

Feb 20, 2016 | Pontiac Cars & Trucks

1 Answer

2002 pt cruizer changed both front wheel bearings and long axle rightside now there is a humming noise on drivers side when driving and ideas thanks


It is entirely possible to have a bad replacement wheel bearing. There are many cheap ones available and I've found that you get what you pay for. I prefer Timken bearings myself. Also, the drive axle nut torque is critical in ensuring that you don't cause bearing failure. Too loose or too tight will cause bearings to fail in short order. The axle nut is not one that can be "shade tree torqued" by "grunt-power".

Jun 29, 2015 | Cars & Trucks

1 Answer

Front wheel bearing torque


The axle nut is 118 ft lbs
The other 3 bolts are a 75 ft lbs

Apr 02, 2014 | 2006 Pontiac Grand Prix

1 Answer

Front axle 2002 highlander


to remove front axle.to loosen front axle nut leave vechicle weight on wheel then just loosen front axle nut because axle nut torque at 217 ft lbs torquehard to loose axle nut with vechicle weight off wheel.okay. you need a 1/2 breaker bar and axle socket to loosen axle nut dont use 12 points sockets need go auto parts store buy right socket for axle nut.okay when you loosen front axle nut you need safely raise support vechicle. need to remove wheels remove fender apron seal remove transaxle fluid remove transfercase oil if you have 4WD.remove hub nut remove stabilizer bar link remove speed sensor remove tie rod end remove lower arm from the ball joint then slide the halfshaft from the hub then carefully pry the shaft from the transaxle.then install new front axle push in make sure front axle snap ring on front axle snap in place inside transmission just pull a little on front axle make its in place. when all done tighten front axle much as you can then when done putting every thing back in place.lower vechicle need torque front axle nut to 217 ft lbs.

Jan 12, 2013 | 2002 Toyota Highlander

1 Answer

How much torque is needed on the axle nut when replacing the front wheel assembly of a 2006 pontiac g6 ?


The drive-axle/hub nut is supposed to be 159 ft-lbs, but know that you are required to use a NEW nut.

Sep 10, 2010 | 2006 Pontiac G6

1 Answer

How do you install a front wheel bearing on a 2001 Pont Montana


jack the vehicle up remove the wheel
remove the brake caliper bottom bolt 15mm. lift the caliper up and slide the caliper pin out
remove the caliper housing bracket 2 - 15mm. bolts
remove the brake rotor
remove the drive axle nut 1 5/16
the remove the hub bearing bolts 3- 13mm. they are in behind (best to use a 13mm flex socket)
disconnect the ABS harness
use a hammer and hit the hub bearing flage (it maybe corroded )
now the hub bearing is out clean the steering knuckle with sandpaper to remove corrosion
install the hub bearing (make sure the ABS harness is in the right position)
and reassemble
hope this helps

Apr 29, 2010 | 2001 Pontiac Montana

2 Answers

Replace front left wheel berring on 2002 GMC Yukon


do not replace only the bearing. replace hub assembly. remove rim/tire , remove caliper, mounting plate, rotor. . un bolt hub assembly, unplug abs. remove front axle nut if 4x4. you may need to rent the axle nut remove kit and hub puller. pull out hub. drive axle reward out of hub. install new part. do not torque hub over 90lbs. check with parts sell for spec

Jan 03, 2010 | 2002 GMC Yukon XL

1 Answer

Replace broken rear coil spring on pontiac montana


PLEASE DON'T FORGET TO RATE!!!

Removal & Installation

Remove or disconnect the following:
  • Brake hose bracket screw from the control arm
  • Shock absorber lower bolt while using a utility stand to support the rear axle
  • Tie rod from the rear axle
  • Spring and insulators after lowering the rear axle

7fc1aec.gif
Exploded view of the coil spring assembly


To install:
  1. Install or connect the following:
    • Insulators and springs on the rear axle with the paint stripe is facing rearward
    • Rear axle tie rod after raising the rear axle into its proper position. Torque the nut to 92 ft. lbs. (125 Nm).
    • Shock absorbers to the rear axle. Torque the upper and lower nuts to 63 ft. lbs. (85 Nm).
    • Brake hose bracket to the control arm. Torque the bolt to 33 ft. lbs. (44 Nm).
  2. Remove the axle supports.

Oct 17, 2009 | 2000 Pontiac Montana

2 Answers

2003 Pontiac Montana Front Wheel Bearings


Remove the wheel, remove the hub nut, remove the brake caliper and rotor, put your socket and extension through the hub flange onto the bearing retainer bolts, undo them, release the abs sensor connector if it has it, remove the bearing and hub flange as an assembly, put the new one on and go backwards from here. Torque the hub nut to 180 ft/lbs, your done.

Apr 08, 2009 | 2003 Pontiac Montana

Not finding what you are looking for?
2002 Pontiac Montana Logo

Related Topics:

451 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8567 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...