Question about 2007 Mazda MAZDA5

1 Answer

Remove mazda 5 rear bumper? - 2007 Mazda MAZDA5

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 4 Answers

No.

Posted on Sep 05, 2012

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

eitan
  • 291 Answers

SOURCE: remove the rear bumper

Removing Prowler Rear Bumpers First remove the four 10 MM bolts holding the trans cooler and drop it down. Support it by attaching one bolt to the lower hole on the cooler frame. This will keep the weight off the lines. This takes two min. and allows easy removal of the elect. lines. Then remove the four bolts on each bumper. The bolts are 13MM and 17MM. You will need a ratchet, sockets, extension and a 13MM open end wrench. If you remove the rear bumpers, you should replace the rear pan with one of the aftermarket ones otherwise you will have big holes staring at the people behind you. Go to prowleronline.com and check the vendors for a couple of options. Maybe you are removeing them to paint and reinstall. Look at this link for some options .. Mine is the 7th post down. http://www.prowleronline.com/ubb/Forum1/HTML/014949.html Hope this helps.

Posted on May 15, 2008

shaggyrat
  • 1224 Answers

SOURCE: Remove rear bumper from 2003 Porche Cayenne

removing takes about 5 minute refiting the back bumper will take about an our to refit the rear bumper if your using power tools

the easiest way to do this is tank some white nail polish mark 3 lines on the mounts on both sides this will give you a guide to placen back the bumper to vehicle

Posted on Jun 10, 2008

  • 4793 Answers

SOURCE: Volkswagen Passat rear bumper removal

all the screws/bolts are underneath the plastic cover.hex head.(allen key)

Posted on Jul 12, 2010

  • 4 Answers

SOURCE: how to remove the front bumper cover on 2002

Remove all eight small set screws (4) on each side in the fender wheel wells. Then remove the four secure bolts on undercarriage of bumper (4). Take a screw driver. (flathead) to the upper portions of both the left and right side of the bumper. Be careful....... These are extremely fragile and you may need to replace them before replacing the bumper. Then comes a bit unnerving part. Removal of the bumper........ (This scarred the **** out of me!!!!) just grab ahold of one of the corners, then gradually pull! That's it. The clips will come out gradually and evenly.

Posted on Feb 20, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove the grill off of a 2011 Mazda CX-7?


It can be removed, but you have to remove the bumper with it. It has many plastic clips around it. Some you can't get to with out the bumper off. Try to.. And you break it. The bumper has plastic buttons to remove top and bottom. Also could be a few screws/bolts to remove a round the fender wells.

Mar 06, 2016 | Mazda Cars & Trucks

1 Answer

How easy is it to damage the front grill-work of the Mazda6?


Depends. Really cold out, these will crack easily. I was rear ended, by a Porsche. Cracked my bumper, we were picking pieces of his off the ground. We were stopped, he couldn't have been doing more than 5 MPH. Frigid that day.

Feb 21, 2016 | 2016 Mazda Mazda6

1 Answer

How do I replace rear parking sensor


You have to take bumper cover off .
Remove rear bumper fascia. Refer to Rear Bumper Fascia Replacement . Disconnect electrical from the rear object sensor. Lift the locking tabs on the housing and remove the rear object sensor.
Preliminary Procedure
  1. Remove the compartment sill plate. Refer to Rear Compartment Sill Trim Plate Replacement .
  2. Remove rear wheel liners. Refer to Rear Wheelhouse Panel Liner Replacement .
1
Rear Fascia Push Pin Retainers (Qty: 2)
2
Rear Fascia Nuts (Qty: 4)
Tighten
10 N?·m (89 lb in)
3
Rear Fascia Bolts (Qty: 2)
4
Rear Fascia Bolts (Qty: 6)
5
Rear Fascia
Tip
?€¢
Energy absorber and fascia are removed together. Cannot be separate on vehicle.


?€¢
Disconnect the electrical connectors.

Dec 22, 2015 | 2006 Cadillac DTS

1 Answer

Need to disable air bags on 2002 mazda protege 5


Disconnect the battery form the car. Remove the airbag fuse under the bonnet. Do the bumper replacement then re-install the fuse before putting the battery back in.

Dec 30, 2012 | 2002 Mazda Protege

1 Answer

How to replace the rear bumper cover on a Chrysler Pacifica


1. Open liftgate. 2. Remove both taillight assemblies by removing 2 hex-head bolts located in the area revealed when the liftgate is opened. 3. Remove 4 plastic retainers on the very bottom of the bumper cover in the rear. 4. Remove 2 phillips head screws in the wheel well rear lip. 5. Remove 4 pop-up plastic retainers in liftgate area. Use two screw drivers to lift the head and then pull the entire retainer out. 6. Remove a hex-head bolt from each side in the area revealed when the taillight assembly was removed. 7. Bend the bumper cover outward on each side to clear the wheel well lip and remove the bumper. Have a blanket or carpet on the ground to protect the bumper. 8. Remove metal clips from tabs that connect the upper bumper cover to the lower bumper cover. 9. Drill out pop-rivets that connect upper bumper cover to lower bumper cover. 10. Push tabs out of slots to separate the upper and lower bumper covers. 11. Release tab locks on chrome trim pieces and remove from upper bumper cover. 12. Reverse this process to replace the bumper cover.

Feb 16, 2010 | 2006 Chrysler Pacifica

1 Answer

I have an 02 Mazda Tribute with a leaking radiator.Are there any tricks in removing the radiator to repair it? The Radiator People told me that they have never done one of these before and may have to...


1. Drain coolant
2 Remove lower splash shields
3. Disconnect the lower radiator hose and the high pressure transaxle line
4. Lower the vehicle
5. Disconnect the transaxle return line
6. Disconnect the upper radiator hose and degas hose
7. Position the hood latch assembly out of the way
8. remove the 2 bolts and the center support
9 remove the 2 top bolts retaining the cooling fan to the radiator
10. remove the upper radiator support brackets, and remove the radiator from the vehicle
11. To install, reverse the removal procedure

Feb 07, 2010 | 2002 Mazda Tribute

2 Answers

Need step by step instructions on how to remove a rear bumper cover on a 2007 nissan altima


Rear Bumper: Service and Repair
REAR BUMPER
Removal and Installation
REMOVAL
1. Remove the LH and RH rear combination lamps.
2. Remove both the rear wheels and tires.
3. Remove the LH and RH splash shields.
4. Remove the rear bumper fascia clips and screws, then remove the rear bumper fascia.
5. Remove the rear energy absorbing foam.
6. Remove the rear bumper reinforcement.
7. Remove the rear bumper supports.
INSTALLATION
Installation is in the reverse order of removal.

c674cde.jpg

Nov 12, 2009 | 2007 Nissan Altima 3.5 Sedan

1 Answer

Install shocks on a mazda miata


You will need a strut compressor if you have rear struts. You will need to remove the upper bolt inside hatch and one connected to axle. compress springs, and remove strut.
If this is regular shocks, lift car up by bumper, remove top and bottom bolts and replace.

Sep 10, 2009 | 1992 Mazda MX-5

1 Answer

Rear bumper on mazda mpv


Removal of the rear bumper on an Mazda 2004 to 2006 MPV.
It's afairly simple task: 1) Open the rear hatch or (door) remove the torx screws at the bottom of the weather strip. 2) Remove both tail lights by unscrewing the two phillip screws on each light, once removed the lights pulling toward the side of the van. Let them hang from the wires. You will see a clip (white in color),pry it out from behind the bumper material and go to the next step. 3) Remove three 8mm head screws in each fender well and three plastic clips. Then remove an 8mm screw at the top corner of the bumper against the rear fender. If your car has splash guards remove them as well. 4) Remove the two clips at the bottom of the bumper attached to the under carriage. 5) Pull the bumper toward the back of the vehicle be careful with the tail lights. Remember, they are hanging loose.
And that's it, you have done it.
Ferni

Oct 07, 2008 | 2005 Mazda MPV

1 Answer

Remove rear bumper from 2003 Porche Cayenne


removing takes about 5 minute refiting the back bumper will take about an our to refit the rear bumper if your using power tools

the easiest way to do this is tank some white nail polish mark 3 lines on the mounts on both sides this will give you a guide to placen back the bumper to vehicle

Jun 09, 2008 | 2003 Porsche Cayenne

Not finding what you are looking for?
2007 Mazda MAZDA5 Logo

Related Topics:

984 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...