Question about 2002 Toyota Sienna

Open Question

TOYOTA PREVIA 2002 SPOILER LENS REMOVAL

PLEASE TELL ME HOW TO REMOVE STOP LIGHT LENS FROM SPOILER TO REPLACE BULB.

Posted by on

  • NZpanda Dec 07, 2008

    Toyota Previa 2001 , i have the same problem, try to find out how to remove the spoiler len to replace the hi stop light bulb.

×

3 Suggested Answers

  • 46 Answers

SOURCE: Toyot Previa - high mounted stop light

it probally has holders so u probally need to give it a tug or use a screwdriver to pry on it carfully not to break the lense

Posted on Jul 08, 2008

LEFTY64
  • 69 Answers

SOURCE: removal and installation of an auto trans in 2002 toyota camry

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Drain the transaxle fluid.
  3. Remove or disconnect the following:

    Negative battery cable. On vehicles equipped with an air bag, wait at least 90 seconds before proceeding Battery Air cleaner assembly Throttle cable from the throttle body Cruise control actuator cover and connector, if equipped Ground wire Starter Speed sensor connectors, direct clutch speed sensor, and the park/neutral position switch connector on the transaxle Solenoid connector on the transaxle Shift control cable Oil cooler hoses Front side transaxle mounting bolts Front engine mounting bolts Oil cooler line mounting bolts from the front frame Upper transaxle to engine mounting bolts

    0900c15280197a59.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Tie the steering rack to the engine support fixture components, as shown-Avalon and Camry
    Front exhaust pipe Engine side covers and undercovers Both halfshafts Front side engine mounting nut Rear side engine mounting bolts (remove hole plugs) Left side transaxle mounting bolts Steering gear housing Front frame assembly Rear end plate mounting bolts Torque converter cover Torque converter retaining bolts Remaining transaxle mounting bolts Transaxle

Posted on Apr 09, 2009

mickha2
  • 145 Answers

SOURCE: How to replace dash light bulb of 1991 Toyota Previa Van

pop fuse cover, remove vent housing, remove speedo upper cover, remove 4 bolts holding speedo remove speedo, change bulb

Posted on Aug 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Third brake light not working all other tail lights & brake lights work fine


This is a simple bulb replacement.Simply pop off the access cover(if you need to) then twist the bulb in a counter-clockwise motion to remove it.Install is opposite of removal.I hope I could help, rate me accordingly, Thanks.

Oct 11, 2010 | 1993 Honda Accord

1 Answer

How to replace dash light bulb of 1991 Toyota Previa van


pop fuse cover, remove vent housing, remove speedo upper cover, remove 4 bolts holding speedo remove speedo, change bulb

Mar 31, 2010 | 1991 Toyota Previa

2 Answers

How to replace right rear stop and tail light?


Should have acsess to lightbulbs in trunk of car.

Open trunk and remove any carpet or cover around light area.

Bulb should be in a socket,turn socket until it comes out of light lens.

Jan 11, 2010 | 2002 Jaguar X-Type

1 Answer

HOW MANY BULBS ARE IN THE REAR LIGHTS (SUCH AS FOR PARKING, REVERSE, BRAKE). IF WARNING LIGHT ON PANEL IS ONE, WOULD I SEE A BURNT OUT BULB?


You may or may not see a burnt out bulb. The dash light can also mean there's a current issue (ie none of the bulbs are lighting)

2 reverse bulbs
2 license plate bulbs
2 turn signal bulbs
2 rear sidemarker bulbs (side of your tail light assembly)
2 running light bulbs which are the same as your stop light bulbs in the tail light assembly
1 to 6 high mount stop light bulbs (if they're in the window and varies on models)
1 strip of LED brake lights if you have a spoiler



Sep 24, 2009 | 2002 Toyota Camry

1 Answer

I have a left front clearance light out how do you get it out 1


Signal and Marker Lights REMOVAL & INSTALLATION Front Turn Signal and Parking Lights
  1. Disconnect the negative battery cable.
  2. At the rear of the front bumper, turn the bulb socket 1⁄4 turn and remove the socket from the parking brake housing.
  3. Remove the bulb from the socket; if necessary, replace the bulb.
  4. If lens replacement is necessary, remove the retaining bolts and remove the lens from the bumper.
  5. To install, reverse the removal procedures. Check the turn signal/parking light operations.
Fig. 1: Common front turn signal/parking light mounting

d16c14b.jpg
Fig. 2: Twist and remove the bulb socket from the back of the turn signal/parking light lens

8b774bd.jpg
Fig. 3: If lens removal is necessary, loosen and remove the retaining bolts

09f4811.jpg

Jul 24, 2009 | 1992 GMC Sonoma

1 Answer

How do you change a front side light bulb


Turn Signal/Marker Light REMOVAL & INSTALLATION
  1. Remove the one retaining screw from the upper corner of the lens.
  2. Tape the end of a pry tool, then carefully extract from the bottom of the lens in a rocking motion till the stud is loosened from the retainer.
  3. NOTE: Do not pry from the back of the lens, this will crack the lens or damage the paint.
  4. Pull the lens assembly straight out from the body towards the front of the vehicle.
  5. Twist and remove the wiring from the back of the lens.
  6. Twist the bulb and remove it from the socket.
Fig. 5: Once the bulb is removed, inspect the socket for corrosion 90916p10.jpg
To install:
  • Before installing a light bulb into the socket, ensure that all electrical contact surfaces are free of corrosion or dirt. NOTE: Before installing the light bulb, note the positions of the two retaining pins on the bulb. They will likely be at different heights on the bulb, to ensure that the bulb is installed correctly. If, when installing the bulb, it does not turn easily, do not force it. Remove the bulb and rotate it 180 degrees from its former position, then reinsert it into the bulb socket.
  • Insert the light bulb into the socket and, while depressing the bulb, twist it 1/8 turn clockwise until the two pins on the light bulb are properly engaged in the socket.
  • To ensure that the replacement bulb functions properly, activate the applicable switch to illuminate the bulb which was just replaced. If the replacement light bulb does not illuminate, either it too is faulty or there is a problem in the bulb circuit or switch. Correct if necessary.
  • Install the socket and bulb assembly into the rear of the lens housing; otherwise, install the lens over the bulb.
  • Insert and secure the lens assembly into the body of the vehicle.
  • Jun 25, 2009 | 1991 Toyota Previa

    1 Answer

    How do you replace the center brake light on a 2003 4Runner


    We have a 2003 4Runner with no spoiler, and no visible accress to the bulb from the interior. You need to access the bulb by prying the red lens from the bottom using a flathead screwdriver. Do not force it all at once! There are 5 clips that hold it in. Push upwards on each clip easing the light out a little each time as you proceed to the next clip. The entire unit will pull out and then you can twist the connector to unhook the wire from the lens assembly. The bulb pulls straight out (no twisting). Bulb is #921.

    Jun 20, 2009 | 2003 Toyota 4Runner

    1 Answer

    Stop light out


    For the brake light open the rear hatch and check beside the tail light. I believe ther is 2 phillips head screws right where the light meets the rear hatch on the body panel. remove them and gently yet firmly pull the lens assembly from the corner of the rear body panel. Squeeze the clips on the back of the socket and twist to remove the socket from the lens. Push gently on the bulb and turn carefully to remove light from the socket replace the light and reverse removal procedure to install.

    Nov 02, 2008 | 2003 Ford Explorer

    2 Answers

    Toyot Previa - high mounted stop light


    This is slightly counter-intuitive, but the plastic lens needs to go in and up before it comes out. After removing the two screws, use something thin and flat to pull down on the underside painted part of the wing between the two screws. A little bit of prying downwards. Two raised lips become visible - they are holding the lens from being able to be pushed up and in. A second pair of hands could help. Then use your thumbs on the lens close to the screws, gripping with your fingers on the top of the wing and squeeze up. POP!

    Jul 08, 2008 | Toyota Previa Cars & Trucks

    Not finding what you are looking for?
    2002 Toyota Sienna Logo

    Related Topics:

    132 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Toyota Experts

    yadayada
    yadayada

    Level 3 Expert

    60541 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21927 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6811 Answers

    Are you a Toyota Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...