Question about 1999 Hyundai Accent

1 Answer

How to remove crankshaft pulley for 1999 hyundai. I only see one nut.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 625 Answers

You need to take that nut or bolt our with the impact air tool
a electric may work but air tool has more power
then it might just slide out by hand but if not sometimes there is like tree little wholes on the pulley and the have thread to install a puller and remoove it

Posted on Jun 01, 2008

2 Suggested Answers

cincinaty5
  • 132 Answers

SOURCE: to remove crankshaft pulley

use a three arm puller to remove this , useing a prybar on the flywheel will cause teeth damage and make for more repairs .

Posted on Sep 21, 2009

  • 7353 Answers

SOURCE: I need help with a crankshaft pulley removal. I

Nut turns LEFT to remove.

Posted on Jan 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

4cyl 2000 honda accord engine stalls while idling, recently died and will only start for short periods... possible problems/solutions?


check for spark and fuel after it dies.

If there is spark but no fuel, then the fuel pump may be bad or a clogged fuel filter.

If there is fuel but not spark, then the ignition control module or the ignition coil could be bad.

Also, check that the timing belt is timing the engine correctly.
Timing Belt & Balancer Belt

Removal & Installation

2.3L Engine

To Remove:



  1. Record anti-theft code for radio.
  2. Disconnect battery negative cable then positive cable.






    honda-03-23-3542.gif



  3. Turn crankshaft pulley until TDC is achieved.
  4. Raise and safely support vehicle.
  5. Remove front tire assembly.
  6. Remove splash shield.
  7. Remove power steering belt.
  8. Remove alternator and alternator bracket.
  9. Safely support engine under oil pan.





    Upper bracket removal
    honda-03-23-3420.gif



  10. Remove stop, detach ground cable and remove upper bracket.
  11. Remove cylinder head cover.
  12. Remove upper cover.
  13. Remove dipstick and tube assembly.
  14. Remove crankshaft pulley.
  15. Remove adjusting nut rubber seal and remove lower cover.





    Timing belt/balancer belt removal
    honda-03-23-3544.gif



  16. Loosen adjusting nut 1 turn.
  17. Push up on balancer belt tensioner to relieve belt tension.
  18. Push down on timing belt tensioner to relieve belt tension.
  19. Tighten adjusting nut 1 turn.
  20. Remove balancer belt and timing belt.


To Install:


NOTE: Clean balancer belt drive pulley, timing belt pulleys and
upper/lower timing cover prior to belt installation.








honda-03-23-3425.gif






  1. Set timing belt drive pulley to TDC by aligning dimple on pulley with dimple
    on oil pump.






    honda-03-23-3426.gif



  2. Set camshaft pulley to TDC so that "UP" mark is at top and grooves align
    with top of cylinder head.





    Timing belt installation
    honda-03-23-3549.gif



  3. Starting with driver pulley, install timing belt in a counterclockwise
    sequence.
  4. Loosen and ten retighten adjusting nut.
  5. Install balancer belt drive pulley.
    NOTE: Inspect rubber seal on lower cover and replace as necessary.

  6. Install lower cover.
  7. Install crankshaft pulley and bolt.
  8. Rotate crankshaft pulley counterclockwise several times to seat belt.
  9. Loosen adjusting nut 1 turn.
  10. Rotate crankshaft counterclockwise 3 teeth on camshaft pulley.
  11. Tighten adjusting nut to 33 ft lb (44 Nm).






    honda-03-23-3542.gif



  12. Turn crankshaft pulley until TDC is achieved.






    honda-03-23-3426.gif



  13. Ensure that camshaft pulley "UP" mark is at top and grooves align with top
    of cylinder head.
  14. Remove crankshaft pulley and lower cover.
  15. Rotate crankshaft to TDC again and lock timing belt adjuster arm with a 6 mm
    timing cover bolt.
  16. Loosen adjuster nut 1 turn and ensure that belt tensioner freely moves.
  17. Push tensioner up and tighten adjusting nut.





    Balancer shaft alignment
    honda-03-23-3556.gif



  18. Remove bolt and washer from maintenance hole.
  19. Using a 6 X 100 mm bolt, scribe a mark 2.9 in (74 mm) from end.
  20. Insert bolt into maintenance hole and hole in balancer shaft.
  21. Install bolt up to scribed line.





    Balancer shaft alignment
    honda-03-23-3557.gif



  22. Align groove on balancer shaft with pointer on oil pump housing.
  23. Install balancer belt and loosen adjusting nut 1 turn to tension.
  24. Retighten bolt.





    Balancer shaft alignment
    honda-03-23-3556.gif



  25. Remove bolt from maintenance hole and install bolt and washer. Tighten to
    22 ft lb (29 Nm).
  26. Reinstall crankshaft pulley.
  27. Loosen adjusting nut 1 turn.
  28. Rotate crankshaft pulley counterclockwise 1 turn and tighten adjusting nut.
  29. Remove bolt from timing belt adjuster arm.
    NOTE: Inspect rubber seal on lower cover and replace as necessary.

  30. Remove crankshaft pulley.
  31. Install lower cover.
  32. Install seal at adjusting nut.
    NOTE: Crankshaft pulley, bolt and washer must be cleaned prior to
    installation.

  33. Lubricate crankshaft pulley bolt between head and washer and bolt threads
    with clean engine oil.






    honda-03-23-3537.gif



    CAUTION
    Do not use impact wrench to perform
    following step.

  34. Install crankshaft pulley and tighten bolt using special tools to 181 ft
    lb (245 Nm)
    .
  35. Install dipstick/tube assembly.
  36. Install upper cover. Tighten bolts to 9 ft lb (12 Nm).
  37. Install cylinder head cover.
  38. Install alternator bracket and alternator.
  39. Install power steering pump belt and alternator belt.





    Upper bracket installation
    honda-03-23-3420.gif



  40. Install upper bracket and tighten fasteners in proper numbered sequence.
  41. Install stop.
  42. Install battery and enter radio anti-theft code.


prev.gif next.gif

Oct 29, 2010 | 2000 Honda Accord

1 Answer

Hiwich timing mark I used to time the balancer shaft on a 99 honda accord with a 2.3L


To Install:
NOTE: Clean balancer belt drive pulley, timing belt pulleys and upper/lower timing cover prior to belt installation.
honda-03-23-3425.gif

  1. Set timing belt drive pulley to TDC by aligning dimple on pulley with dimple on oil pump. honda-03-23-3426.gif

  2. Set camshaft pulley to TDC so that "UP" mark is at top and grooves align with top of cylinder head. Timing belt installation honda-03-23-3549.gif

  3. Starting with driver pulley, install timing belt in a counterclockwise sequence.
  4. Loosen and ten retighten adjusting nut.
  5. Install balancer belt drive pulley. NOTE: Inspect rubber seal on lower cover and replace as necessary.
  6. Install lower cover.
  7. Install crankshaft pulley and bolt.
  8. Rotate crankshaft pulley counterclockwise several times to seat belt.
  9. Loosen adjusting nut 1 turn.
  10. Rotate crankshaft counterclockwise 3 teeth on camshaft pulley.
  11. Tighten adjusting nut to 33 ft lb (44 Nm). honda-03-23-3542.gif

  12. Turn crankshaft pulley until TDC is achieved. honda-03-23-3426.gif

  13. Ensure that camshaft pulley "UP" mark is at top and grooves align with top of cylinder head.
  14. Remove crankshaft pulley and lower cover.
  15. Rotate crankshaft to TDC again and lock timing belt adjuster arm with a 6 mm timing cover bolt.
  16. Loosen adjuster nut 1 turn and ensure that belt tensioner freely moves.
  17. Push tensioner up and tighten adjusting nut. Balancer shaft alignment honda-03-23-3556.gif

  18. Remove bolt and washer from maintenance hole.
  19. Using a 6 X 100 mm bolt, scribe a mark 2.9 in (74 mm) from end.
  20. Insert bolt into maintenance hole and hole in balancer shaft.
  21. Install bolt up to scribed line. Balancer shaft alignment honda-03-23-3557.gif

  22. Align groove on balancer shaft with pointer on oil pump housing.
  23. Install balancer belt and loosen adjusting nut 1 turn to tension.
  24. Retighten bolt. Balancer shaft alignment honda-03-23-3556.gif

  25. Remove bolt from maintenance hole and install bolt and washer. Tighten to 22 ft lb (29 Nm).
  26. Reinstall crankshaft pulley.
  27. Loosen adjusting nut 1 turn.
  28. Rotate crankshaft pulley counterclockwise 1 turn and tighten adjusting nut.
  29. Remove bolt from timing belt adjuster arm. NOTE: Inspect rubber seal on lower cover and replace as necessary.
  30. Remove crankshaft pulley.
  31. Install lower cover.
  32. Install seal at adjusting nut. NOTE: Crankshaft pulley, bolt and washer must be cleaned prior to installation.
  33. Lubricate crankshaft pulley bolt between head and washer and bolt threads with clean engine oil. honda-03-23-3537.gif

    CAUTION
    Do not use impact wrench to perform following step.
  34. Install crankshaft pulley and tighten bolt using special tools to 181 ft lb (245 Nm).
  35. Install dipstick/tube assembly.
  36. Install upper cover. Tighten bolts to 9 ft lb (12 Nm).
  37. Install cylinder head cover.
  38. Install alternator bracket and alternator.
  39. Install power steering pump belt and alternator belt. Upper bracket installation honda-03-23-3420.gif

  40. Install upper bracket and tighten fasteners in proper numbered sequence.
  41. Install stop.
  42. Install battery and enter radio anti-theft code.
prev.gif next.gif

Jul 03, 2010 | Cars & Trucks

3 Answers

I would like to know where the crankshaft gasket is? I have a 1994 dodge spirit, a 6 cyl. How hard is it for me to replace the gasket?


3.3L and 3.8L Engines
  1. Raise and safely support the front of the vehicle on jackstands.
  2. Remove the right front wheel and inner splash shield.
  3. Remove the accessory drive belt from the engine.
  4. Remove the center bolt of the crankshaft pulley.
  5. Using a claw-type gear puller, remove the crankshaft pulley from the crankshaft. When using the puller, make certain that the claws are situated on the inner section of the pulley. If the claws are used on the outer section of the pulley, the pulley will be damaged.
  6. Use tool C-4991 or the equivalent to remove the oil seal from the timing chain cover. Make certain not to damage the crankshaft seal surface of the cover. Fig. 10: Use a claw-type gear puller to remove the crankshaft pulley/damper — 3.3L and 3.8L engines 86723231.gif
    Fig. 11: Use the seal remover tool C-4991 to remove the crankshaft oil seal — 3.3L and 3.8L engines 86723230.gif
    To install:
  7. Install the new seal by using tool C-4992 or the equivalent. Place the seal into the opening with the seal spring towards the inside of the engine. Install the seal until flush with the cover.
  8. To install the crankshaft pulley to the crankshaft a 5.9 in. (150mm) long bolt, a thrust bearing and washer, and plate L-4524 or equivalent.
    1. Tap the crankshaft pulley onto the crankshaft with a rubber or plastic mallet making sure to hit the pulley on the center portion.
    2. Once the pulley is started onto the crankshaft, install a nut the thrust bearing and washer, and the plate L-4524 onto the bolt.
    3. Thread the bolt into the end of the crankshaft and screw it in at least 2 or 3 complete turns.
    4. Tighten down on the nut on the bolt to slowly press the pulley onto the crankshaft until completely seated.
    5. Remove the bolt, nut, washer and thrust bearing, and plate L-4524 from the crankshaft. Fig. 12: Installing the crankshaft pulley — 3.3L and 3.8L engines 86723229.gif

  9. Install the center crankshaft pulley bolt and tighten it to 40 ft. lbs. (54 Nm).
  10. Install the accessory drive belt and tighten by following the instructions in Section 1.
  11. Install the splash shield and front wheel.
  12. Lower the vehicle to the ground.

Jul 16, 2010 | 1994 Dodge Spirit

2 Answers

To remove crankshaft pulley


no easy way, yopu will need a air impact 1/2" drive. Unles you can get to the flywheel and jam it, or even take the starter out and jam it. with a pry bar or something.

Sep 21, 2009 | Hyundai Motor 2004 Sonata

1 Answer

Broken crankshaft pully, need to know how to remove to replace


Normally...three bolts for the pulley assembly, and one large center bolt, and yes...a steering wheel puller will work, but make sure the puller doesn't sit into the center hole threads, or they will be destroyed. Sometimes a nut in here will prevent that.

Jul 28, 2009 | 2003 Hyundai Santa Fe

1 Answer

What is the procedure on removing an alternator from a 2001 Taurus with a duratec engine?


Okay, on your engine, the alternator is mounted below the rear cylinder bank of the engine, at the rear of the engine compartment. It'll be easier to access it from the driver's side front fenderwell (take off the right front tire then the plastic lining) or under the car. You might want to go ahead and remove both the liner and work from underneath as you'll need to remove your crankshaft pulley.

1: Disconnect the negative batery cable.

2: Disconnect the electrical connections from the alternator. The output wire is secured by a nut on the output terminal.

3: Revove the serpentine/drive belt.

4: Remove two bolts and one stud bolt that secure the alternator to it's bracket. Remove the crankshaft pulley.

Installation is reverse of removal.

After installing the alternator, reinstall the drivebelt and reconnect the negative battery cable.

To remove the crank-shaft pulley

1: As you'll aready have the wheel, liner, negative battery cable, and serpentine/drivebelt removed, as well as the car on jackstands, I'll omit those steps.

2: Remove the driveplate access cover and hold the ring gear teeth with a large scredriver or pry bar to prevent the crankshaft from turning.

3: Remove the nuts that secure the pullley bracket to the engine front cover. Remove the pulley and bracket.

4: The crankshaft pulley screws into the harmonic balancer with a left hand thread (reverse threaded so rightly loosey lefty tighty). Trun the crankshaft pulley clockwise to loosen and remove it.

5: Hopefully this is where you'll end with the pulley. The harmonic balancer is no fun to remove, but let me know if you need to know this too. After you have your alternator installed, put the pulley back onto the harmonic balancer before installing the serpentine/ drive belt.

Hope this info helps.

Jun 26, 2009 | 1999 Ford Taurus

1 Answer

How do i undo the nut on crankshaft pulley.


you will have to use a fly wheel locking tool or i usually just use a large flat tip screw driver and hold the fly wheel from turning while a friend loosens the nut on the pulley.

Mar 30, 2009 | 1999 Hyundai Accent

1 Answer

Cant get the crankshaft pulley off


It's most likely right hand thread. You will have to use a large breaker bar to get enought leverage to remove this nut. Or you can use what ever you have and place a steel pipe on the end of it for extra leverage. If it doesn't budge, you may have to soak it in penetrating oil, and use an impact wrench. Make sure you remove the large washer under the nut "before" you remove pulley.

Nov 11, 2008 | 1997 Jeep Tj

Not finding what you are looking for?
1999 Hyundai Accent Logo

Related Topics:

280 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...