Question about 1996 Plymouth Voyager

1 Answer

Connections for fuel pump - 1996 Plymouth Voyager

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Plymouth Master
  • 7,772 Answers

This is all I could find. Do you count 3 wires? The pump is dark green/white stripe. Ground is Black. The other one must be fuel level--dark blue?


connections for fuel pump - b8c2e73.gif

Posted on Oct 13, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the fuel pump located on a 92 Lexus SC300?


Fuel Pump REMOVAL AND INSTALLATION ES300 CAUTION
Fuel injection systems remain under pressure even after the engine has been turned OFF. The fuel system pressure must be relieved before disconnecting any fuel lines. Failure to do so may result in fire and/or personal injury.
  1. Relieve the fuel system pressure.
  2. With the ignition switch in the LOCK position, disconnect the negative battery terminal. If equipped with an air bag system, wait at least 90 seconds or longer before performing any other work.
  3. Remove the rear seat cushion.
  4. Disconnect the fuel pump connector. CAUTION
    The Supplemental Inflatable Restraint (SIR) system must be disarmed before removing the fuel pump. Failure to do so may cause accidental deployment of the air bag, resulting in unnecessary SIR system repairs and/or personal injury.
  5. Remove the floor service hole cover. NOTE: Do not lift the fuel pump assembly up using the wire harness.
  6. Remove the fuel filler cap. Disconnect the fuel outlet pipe and the return hose from the pump bracket.
  7. Remove the 8 screws and lift out the pump/bracket assembly with gasket.
  8. Remove the fuel pump lead wire.
  9. Pull the lower end of the pump off of the bracket.
  10. Disconnect the fuel hose from the pump and remove the pump.
  11. Remove the rubber cushion from the pump. To install:
  12. Install the filter and rubber cushion on the new pump and install the pump on the bracket.
  13. Connect the fuel hose and the wire connector on the pump.
  14. Using a new gasket, install the pump and tighten the eight screws to 35 inch lbs. (4 Nm).
  15. Connect the fuel pipe and return hose to the pump and tighten the bolts to 22 ft. lbs. (29 Nm).
  16. Connect the wire, install the service cover and replace the rear seat.
  17. Connect the negative battery cable.
  18. Start the engine and check for leaks. Fig. 1: Fuel pump assembly - ES300 294126.gif
GS300, LS400, SC300 and SC400
  1. Disconnect the negative battery cable. Wait at least 90 seconds before performing any other work.
  2. Remove the trunk floor mat.
  3. Remove the trunk trim cover.
  4. Disconnect the fuel pump electrical connector.
  5. Remove the rear seat bottom and seat back.
  6. Remove the partition cover.
  7. Remove the mounting bolts and remove the fuel pump set plate.
  8. Remove the three nuts and disconnect the fuel pump bracket from the tank.
  9. Disconnect the fuel hose from the bracket. Remove the pump, bracket and set plate as an assembly. To install:
  10. Install a new gasket on the set plate. Connect the fuel hose to the pump and bracket,
  11. Install the pump and bracket assembly with the three nuts; tighten the nuts to 48 inch lbs. (5 Nm). Install the set plate and tighten the bolts to 26 inch lbs. (3 Nm).
  12. Install the panel partition
  13. Install the rear seat cushion and back.
  14. Connect the fuel pump electrical connector.
  15. Install the trim panel.
  16. Install the spare tire and the trunk floor mat.
  17. Connect the negative battery cable.
  18. Start the engine; check the fuel system for leaks
  19. Road test the vehicle for proper operation.

Oct 13, 2010 | 1992 Lexus Sc 300

2 Answers

My fuel pump went out again in my truck. I had it done the first time and was told it was quite the chore. This time I don't have the 600$ to have it done again so I'm going to try it myself. I need a...


Fuel Pump Removal & Installation Main To Remove:
  1. Disconnect battery negative cable.
  2. Relieve fuel system pressure.
  3. Raise and safely support vehicle.
  4. Remove fuel tank.
  5. Remove fuel sender assembly by turning cam lock counterclockwise. gm-04-00-954.gif

  6. Remove fuel sender assembly from fuel tank.
To Install:
  1. Using NEW O-ring seal, Install fuel pump sender to fuel tank.
  2. Install cam lock assembly and turn clockwise to lock.
  3. Install fuel tank.
  4. Cycle ignition switch OFF and OFF and check for fuel leaks.
Balance 7.4L To Remove:
  1. Disconnect battery negative cable.
  2. Relieve fuel system pressure.
  3. Disconnect electrical connector.
  4. Clean both fuel pipe connections and area surrounding fuel pump to avoid contamination of fuel system. gm-05-74-997.gif

  5. Disconnect fuel pipes at fuel pump.
  6. Slide fuel pump out of bracket.
To Install:
  1. Install NEW O-ring seals on fuel pipes.
  2. Position pump in pump bracket.
  3. Connect fuel feed and suction pipes to pump.
    • Torque to: 22 ft lbs. (30 Nm).
  4. Connect electrical connector.
  5. Connect battery negative cable.
  6. Cycle ignition switch OFF and OFF and check for fuel leaks.
prev.gif next.gif

Oct 13, 2010 | 1997 GMC Sierra

1 Answer

Access panel for fuel pump


There is none:

Fuel Tank & Fuel Pump Module Assembly Removal & Installation To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Shift the vehicle into NEUTRAL and position it on a hoist.
  3. Release the fuel pressure.
  4. Disconnect the negative battery cable.
  5. Remove the fuel tank filler cap.
  6. Drain as much fuel from the tank as possible.
  7. Using suitable hose pinching pliers, clamp the fuel tank filler hose. Clamp the fuel tank filler hose in the location shown ford-05-00-396.gif

  8. Disconnect the three quick connect couplings from the fuel tank tubes at the tank.
  9. Disconnect the fuel pump electrical connector.
  10. Disconnect the fuel filter inlet tube from the filter.
  11. Position a suitable lifting device under the fuel tank.
  12. Remove the two fuel tank support strap bolts.
  13. Lower the fuel tank to access the fuel pump module while swinging the fuel tank support straps away from the tank.
  14. Clean the area around the fuel pump mounting flange.
  15. Disconnect the fuel pump module electrical connector and the fuel pump module fuel outlet tube.
  16. Using the special tool, turn the fuel pump module retaining ring counterclockwise and remove it. CAUTION
    The fuel pump module must be handled carefully to avoid damage to the float arm, filter and convolute hoses.
  17. Turn the fuel pump module counterclockwise and the fuel pump module will release from the locking tabs. Remove the fuel pump module from the fuel tank.
To Install:
  1. Install the fuel pump module in the fuel tank.
  2. Connect the fuel pump module electrical connector and the fuel pump module fuel outlet tube.
  3. Raise the tank into position and install the mounting strap bolts. Tighten the bolts to 26 ft-lbs (35 Nm).
  4. Connect the fuel lines and electrical connectors at the fuel tank.
  5. Lower the vehicle and refill the tank.
  6. Connect the negative battery cable.
  7. Turn the ignition key to the ON position to pressurize the fuel system.
  8. Visually inspect the fuel system for leaks.
prev.gif next.gif

Oct 05, 2010 | 2000 Ford Taurus

1 Answer

Instructions on how to remove fuel pump for 95 chevy blazer 4x4


Removal & Installation
To Remove:


  1. Properly relieve the fuel system pressure.
  2. Drain the fuel tank through the filler pipe.
  3. Support the fuel tank.
  4. Remove or disconnect the following:

    • Negative battery cable
    • Filler neck
    • Shield and tank straps
    • Fuel lines and vapor hose from pump and tank
    • Electrical connection from fuel pump
    • Fuel tank
    • Fuel pump/sending unit assembly by turning the locking ring (located on top
      of the fuel tank) counterclockwise using a spanner wrench
    • Fuel pump from the fuel lever sending device

To Install:


  1. Install or connect the following:

    • Fuel pump in tank with new seal around opening
    • Tank and connect fuel lines and vapor hose
    • Tank to the frame

      1. Torque to: 33 ft. lbs. (45 Nm)

    • Shield
    • Fuel filler neck and clamp
    • Negative battery cable

  2. Refill the tank.
  3. Run the engine and check for leaks.






View of the in-tank fuel pump assembly.
7924jg21.gif




prev.gif next.gif

Sep 23, 2010 | Chevrolet Blazer Cars & Trucks

3 Answers

Needs fuel pump


Removal & Installation To Remove:
  1. Properly relieve the fuel system pressure.
  2. Drain the fuel tank through the filler pipe.
  3. Support the fuel tank.
  4. Remove or disconnect the following:
    • Negative battery cable
    • Filler neck
    • Shield and tank straps
    • Fuel lines and vapor hose from pump and tank
    • Electrical connection from fuel pump
    • Fuel tank
    • Fuel pump/sending unit assembly by turning the locking ring (located on top of the fuel tank) counterclockwise using a spanner wrench
    • Fuel pump from the fuel lever sending device
To Install:
  1. Install or connect the following:
    • Fuel pump in tank with new seal around opening
    • Tank and connect fuel lines and vapor hose
    • Tank to the frame
      1. Torque to: 33 ft. lbs. (45 Nm)
    • Shield
    • Fuel filler neck and clamp
    • Negative battery cable
  2. Refill the tank.
  3. Run the engine and check for leaks.
View of the in-tank fuel pump assembly. 7924jg21.gif

prev.gif next.gif

Sep 18, 2010 | 1997 Chevrolet Blazer

1 Answer

How to put hi pressure fuel pump into the engine,it does not have any mark on the pump rotor?


prev.gif next.gif Removal & Installation To Remove:
  1. Properly relieve the fuel system pressure.
  2. Drain the fuel tank through the filler pipe.
  3. Support the fuel tank.
  4. Remove or disconnect the following:
    • Negative battery cable
    • Filler neck
    • Shield and tank straps
    • Fuel lines and vapor hose from pump and tank
    • Electrical connection from fuel pump
    • Fuel tank
    • Fuel pump/sending unit assembly by turning the locking ring (located on top of the fuel tank) counterclockwise using a spanner wrench
    • Fuel pump from the fuel lever sending device
To Install:
  1. Install or connect the following:
    • Fuel pump in tank with new seal around opening
    • Tank and connect fuel lines and vapor hose
    • Tank to the frame
      1. Torque to: 33 ft. lbs. (45 Nm)
    • Shield
    • Fuel filler neck and clamp
    • Negative battery cable
  2. Refill the tank.
  3. Run the engine and check for leaks.
View of the in-tank fuel pump assembly. 7924jg21.gif

prev.gif next.gif

Jul 15, 2010 | 2004 Chevrolet Blazer

1 Answer

How do I remove fuel pump off 01 olds silhouette. Dropped the tank down already


2001 Oldsmobile Truck Silhouette 3.4L SFI 6cyl
Fuel Pump - Removal & Installation
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Properly relieve the fuel system pressure.
  3. Drain and remove the fuel tank from the vehicle
  4. Remove or disconnect the following:
    Negative battery cable Quick-connect fittings at the fuel pump Fuel pump locking nut with a Fuel Pump Spanner Wrench J 39348 Fuel pump assembly from the fuel tank and discard the O-ring
To install:
  1. Install or connect the following:
    New O-ring on the fuel tank Fuel pump into the fuel tank making certain not to fold or twist the strainer and that it does not interfere with the full travel of the float arm Fuel pump locking nut with the scanner tool Quick-connect fittings at the fuel pump Fuel tank and fill the tank Negative battery cable
  2. Prime the fuel system as follows:
    1. Turn the ignition switch ON for two seconds.
    2. Turn the ignition switch OFF for 10 seconds.
    3. Turn the ignition switch ON and checks for leaks. Repair if necessary.


Fuel Pump/SenderRemoval & Installation
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Properly relieve the fuel system pressure.
  3. Disconnect the negative battery cable.
  4. Drain the fuel tank into an approved container.
    WARNING Do not attempt to straighten any kinked nylon fuel lines. Replace any kinked nylon fuel feed or return pipes in order to prevent damage to the vehicle.
    WARNING Do not attempt to repair sections of nylon fuel pipes. If the nylon fuel pipes are damaged, replace the pipes.
  5. Raise the vehicle.

    1edb6c2.jpg
    Fig. Showing the fuel tank assembly and related components
  6. Disconnect the fuel supply pipe (5) quick-connect fitting.
  7. Disconnect the evaporative emission (EVAP) purge pipe (6) quick connect fitting at the EVAP canister.
  8. Loosen the fuel tank filler pipe hose clamp.
  9. Disconnect the fuel tank filler from the fuel tank.
  10. Disconnect the vapor recirculation pipe from the filler tube.
  11. Remove the fuel tank shield.
  12. With the aid of an assistant, support the fuel tank.
  13. Remove the fuel tank strap attaching bolts.
  14. Disconnect the fuel sender and the fuel tank pressure (FTP) sensor electrical connectors at the body pass through.
  15. Remove the fuel tank from the vehicle.
  16. Remove the fuel sender assembly (3).

    f523c95.jpg
    Fig. Identifying the fuel sender assembly
  17. Disconnect the fuel sender electrical connections (3).
  18. Clean all of the fuel pipe connections, all of the hose connections, and all of the areas surrounding the connections before disconnecting the connections in order to avoid possible contamination of the fuel system.
  19. Disconnect the fuel supply pipe quick-connect fitting (4) at the fuel sender assembly.
  20. Disconnect the evaporative emission (EVAP) pipe quick-connect fittings (5, 6) at the fuel sender assembly.
    CAUTION Do NOT use impact tools. Significant force will be required to release the lock ring. The use of a hammer and screwdriver is not recommended. Secure the fuel tank in order to prevent fuel tank rotation.

continue...

Jun 23, 2010 | 2002 Oldsmobile Silhouette

1 Answer

Location of fuel pump for 1992 subaru loyale wagon


REMOVAL & INSTALLATION

See Figure 1


0900c15280067055.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 1: Fuel pump assembly mounted under the vehicle-1.8L engine
  1. Release the fuel system pressure. Do not reconnect the fuel pump harness.
  2. Disconnect the negative battery cable.
  3. Raise and support the vehicle safely on jackstands.
  4. Clamp the middle portion of the hose connecting the fuel tank pipe and the pump to prevent fuel from flowing out of the tank when unfastened.
  5. Loosen the hose clamp and disconnect the hose.
  6. Remove the three pump bracket mounting bolts and remove the pump together with the pump damper.

To install:
  1. Install the fuel pump and damper, and tighten the bolts securely.
  2. Install the hose and tighten the clamp screw to 9-13 inch lbs. (1.0-1.5 Nm).
  3. Install the pump bracket in position to the vehicle body and secure it with the bolts.

Take care to position the rubber cushion properly.
  1. Connect the pump harness.
  2. Connect the negative battery cable and test the fuel pump for proper operation.
  3. Check for fuel leaks.

TESTING

  1. Turn the ignition ON and listen for the fuel pump to make a growling sound. Turn the ignition OFF .
  2. Release the fuel system pressure. Disconnect the pump harness and crank the engine for 5 seconds or more. If the engine starts, allow it to run until it stops. Turn the ignition OFF and install the fuel pump connector.
  3. Disconnect the fuel hose at the fuel pump.
  4. Connect a gauge in-line using a T-fitting.
  5. Start the engine and measure the fuel pressure. If the fuel pressure is not 36-50 psi (248-344 kPa), replace the pump.
  6. Release the fuel system pressure and remove the gauge.

May 22, 2010 | 1992 Subaru Loyale

2 Answers

It will not start. We changed the fuel pump three times. Each time the new fuel pump will not hum or buzz when you turn the igntion.


Did you check the fuel pump wiring harness, fuel pump ground , power to the fuel pump, fuel pump fuse , fuel pump relay

Oct 18, 2009 | 1999 Chevrolet Venture

Not finding what you are looking for?
1996 Plymouth Voyager Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...