Question about 2003 Chevrolet Blazer

1 Answer

Check engine light on Checked diagnostics received answer DTC 9440

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 6,826 Answers

Are you sure the diagnostic trouble code was 9440? I couldn't find a listing for that under generic codes.

Posted on Oct 13, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Shift light flashing no OD Changed Trans ecm/pcm shift hold light button, coil No change. CYL missfire, 2 & 3 Diagnostics code on Trans is u0401 Invalid data received from ecm/pcm/a


Circuit Description
Modules that are connected to the shared communication circuits monitor for serial data communications during normal vehicle operation. Operating information and commands are exchanged among the modules. The modules have pre-recorded information about what messages are needed to be exchanged on the serial data circuits for each virtual network. The messages are usually supervised and some periodic messages are used by the receiver module as an availability indication of the transmitter module.

DTC U0401 TCM received invalid data from ECM
Conditions for Setting the DTC
The transmission control module (TCM) detects an invalid throttle position signal, engine speed signal and/or engine coolant temperature signal for more than 2 seconds.

Action Taken When the DTC Sets
• The TCM will store the DTC when a failure is detected on the first ignition cycle.
• The TCM will illuminate the HOLD lamp.
• The TCM can no longer determine the validity of any information it may or may not receive from the engine control module (ECM). Therefore the TCM substitutes default values for engine speed, throttle position, and other engine data signals.
• Transmission operation will be reduced, affecting shift points, torque converter clutch operation, and other driveability concerns.

Diagnostic Aids
• An intermittent malfunction may be caused by a fault in the electrical circuit. Inspect the wiring harness and the components for an intermittent condition. Refer to Intermittent Conditions in Engine Controls 1.6L.
• Repair any electrical circuit faults that were found. Refer to Wiring Repairs in Wiring Systems.
• Faulty ECM and/or TCM

Install a scan tool.
Turn ON the ignition, with the engine OFF.
Save the DTC and Freeze Frame information into the scan tool memory.
Perform the scan tool Clear DTC Information function for the transmission control module (TCM) and the engine control module (ECM).
Operate the vehicle for 1 minute or until the MIL illuminates.
Check the TCM for DTCs.
Is the Malfunction Indicator Lamp (MIL) On?
--
YES - Go to Step 2
NO - Repair the wiring connectors for intermittent failure

Select request DTC status from the Diagnostic Trouble Codes Information menu
Request DTC by status
Is DTC U0401 displayed?
--
YES - Go to Step 3
NO - Repair the wiring connectors for intermittent failure
3
Turn OFF the ignition.
Disconnect connector A from the TCM.
Turn the ignition ON, with the engine OFF.
Measure the resistance between terminal A17 of the TCM wiring connector and terminal K14 of the ECM wiring connector.
Measure the resistance between terminal A7 of the TCM wiring connector and terminal K15 of the ECM wiring connector.
Was the resistance the specified value for both circuits?
0 ohms
YES - Go to Step 5
NO - Go to Step 4

Mar 19, 2016 | 2005 Chevrolet Aveo

2 Answers

Bought car at auction- no keys. Had key made at GM dealer. Programmed key- key works. Car wont start- Codes are P0633 and P1629. cannot clear codes


DTC P0633 : Theft Deterrent Key Not Programmed

When learning the pre-release password, as well as the challenge and response sequence, the engine control module (ECM) is placed in learn mode. DTC P0633 will set automatically as an indicator that the system is in learn mode and not as a fault indicator. Once the password and challenge/response are learned, learn mode will be exited when the engine is successfully started. At this point, the DTC will be cleared. If the ECM does not exit learn mode, P0633 will remain current and indicate a fault.
The "key" referenced in the DTC descriptor does not refer to the vehicle key. In this case, "key" is referring to the challenge response.
DTC P0633 requires a successful engine start to exit the learn procedure and clear the DTC. If an unrelated malfunction exists that causes engine starting to be disabled or otherwise unavailable, learn mode will not exit and DTC P0633 will remain current. In this situation, the cause of the inoperative engine starting must be corrected before diagnosing DTC P0633.
DTC P1629: Theft Deterrent Fuel Enable Signal Not Received
The theft deterrent module (TDM) sends the pre-release password to the engine control module (ECM) via the serial data circuit. The ECM then sends a challenge to the TDM. Both the ECM and TDM perform a calculation on this challenge. If the calculated response from the TDM equals the calculation performed by the ECM, the ECM will allow vehicle starting.
DTC P1629 is an indicator that the challenge response was not received within the required 2 second window. This does not necessarily indicate a fault is present with the TDM or ECM. Factors such as a long engine crank, a delay in the serial data communication, or B-codes set in the TDM will cause DTC P1629 to set. This DTC should not be used as a fault indicator, but rather as a symptom to assist in the diagnosis of these other systems.
Who checked the codes , you -dealer ? You need to have BCM checked for codes B - codes ! you need a up scale diagnostic scan tool for that , dealer Tech -2 !
DTC B3935 57 : Transponder Authentication Error
DTC B3976 46 : Unconfigured Transponder/Vehicle Configuration Not Programmed
DTC B3060 : Unprogrammed Transponder Identification Code Received
DTC B3055: No Transponder Modulation or No Transponder
DTC B3031: Security System Controller In Learn Mode

Aug 07, 2015 | 2006 Buick Lucerne

1 Answer

2008 jeep cherokee hemi engine light its on i brought to fix it and they change 4 sensor and the cadilac converter.


You need to have PCM / ECM - engine computer checked for DTC'S - diagnostic trouble codes an go from there ! there are hundreds of codes these newer vehicles can set ! I hope these people who changed the sensors an catalytic converter checked codes first ! You never ever just replace parts !!!!!!!! A DTC will lead in a diagnostic direction ! Check Engine Code Scanner Advance Auto Parts

Feb 22, 2015 | Jeep Cars & Trucks

1 Answer

Acadia 2009 code C0561 what does it mean?


You won't find this information in a Haynes manual ! I know , I work for a GMC dealership , along with Chevy and Cadillac ! this information I'm adding is right out of GMC service information .
Diagnostic Instructions
?€¢
Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.


?€¢
Review Strategy Based Diagnosis for an overview of the diagnostic approach.


?€¢
Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptors
DTC C0561 71: System Disabled Information Stored Invalid Serial Data Received

DTC C0561 72: System Disabled Information Stored Alive Counter Incorrect

DTC C0561 74: System Disabled Information Value of Signal Protection Calculation Incorrect

Circuit/System Description
The electronic brake control module (EBCM) receives serial data messages from the body control module (BCM), engine control module (ECM), instrument panel cluster (IPC), and the transmission control module (TCM) which are needed to perform antilock brake system (ABS), vehicle stability enhancement system (VSES), or traction control system (TCS) functions.
Conditions for Running the DTC
Ignition voltage is greater than 10 volts.
Conditions for Setting the DTC
The EBCM receives an invalid serial data message from another module.
Action Taken When the DTC Sets
?€¢
The EBCM disables the traction control system (TCS)/ vehicle stability enhancement system (VSES).


?€¢
A DIC message and/or a warning indicator may be displayed.

Conditions for Clearing the DTC
?€¢
The condition for the DTC is no longer present.


?€¢
The EBCM clears the history DTC when a current DTC is not detected in 100 consecutive drive cycles.

Diagnostic Aids
This DTC indicates that there are no problems in the EBCM. The BCM, ECM, IPC and the TCM should be checked for a possible fault.
Reference Information
Schematic Reference
Antilock Brake System Schematics
Connector End View Reference Component Connector End Views
Description and Operation ABS Description and Operation
Electrical Information Reference ?€¢
Circuit Testing


?€¢
Connector Repairs


?€¢
Testing for Intermittent Conditions and Poor Connections


?€¢
Wiring Repairs
Scan Tool Reference Control Module References for scan tool information
Circuit/System Verification

  1. With a scan tool, view the Invalid Signal Data Display.
  2. If no invalid signal are present, view Signal Fault Data in the Enhanced DTC Data.
  3. Refer to appropriate module for diagnosing the invalid message data.
  4. Do not replace the EBCM due to this DTC fault.
You would need a factory scan tool or equivalent too diagnose this ,not a code reader . So do your self a favor an take to a dealership. I've been doing this for thirty years .

Sep 26, 2014 | 2007 GMC Acadia SLE

1 Answer

Where is the obd2 connector location on holden ra rodeo v6


isuzimpuls.gif
Connect white (test lead) and black (ground lead) wires that are branched from harness approximately eight inches from ECM. After leads are grounded, the "Check Engine" light will flash the diagnostic trouble codes. The DTC's are indicated by the flashing CEL.
FLASH, FLASH, pause, FLASH, FLASH, FLASH = Code 23.
If only one diagnostic trouble code is stored, the DTC will repeat continuously until test leads are disconnected. If more than one diagnostic trouble code is stored, each DTC will repeat three times, starting with the lowest, then proceed to the next DTC. After all DTC's have been displayed, the pattern will repeat.I-MARK 84-85
Connect male and female test leads taped into wire harness near ECM. After leads are connected, the "Check Engine" lamp will flash the trouble codes. The DTC's are indicated by the flashing CEL.
FLASH, FLASH, pause, FLASH, FLASH, FLASH = Code 23.
If only one diagnostic trouble code is stored, the DTC will repeat continuously until test leads are disconnected. If more than one diagnostic trouble code is stored, each DTC will repeat three times, starting with the lowest, then proceed to the next DTC. After all DTC's have been displayed, the pattern will repeat.
86-87 Impulse located near the ECM connector, is used to actuate the Engine Control Module (ECM) trouble code memory within the module. Two terminals (A and C) of this connector are used to activate the diagnostic trouble code system in the ECM. With the ignition switch turned On, engine Off, connect a jumper wire between terminals A and C. The "Check Engine" lamp will begin by flashing a DTC 12. DTC 12 = flash, pause, flash, flash. There will be a longer pause and a code 12 will repeat two more times. This code indicates the self-diagnostic system is operating. The cycle will then repeat until the engine is started or the ignition is switched Off. In most cases, DTC's will be checked with the engine running since no DTC's other than DTC 12 or 51 will be present without the engine running. Remove jumper wire from ALDL connector before starting engine. Reconnect jumper wire after engine is running.

Throttle Body Fuel Injection

The ECM test connection is located under the center console.
A built-in, self diagnostic system will identify problems in the throttle body fuel injection system. When a problem is detected, the diagnostic system will illuminate the "Check Engine" light.
When the engine is started, the Check Engine light should turn off.. If the light remains lit, the self diagnostic has detected a problem. To determine where the problem exists, ground the "Test" terminal of the connector with the ignition On, engine Off and watch the check engine light. Each DTC will flash three times (lowest to highest).

Aug 21, 2014 | Holden Rodeo Cars & Trucks

1 Answer

What is service engine light code 12 mean



READING CODES USING MIL (CHECK ENGINE) LAMP

Be advised that the MIL or CHECK ENGINE light can only perform a limited number of functions and it is a good idea to have the system checked with a scan tool to double check the circuit function.

  1. Within a period of 5 seconds, cycle the ignition key ON - OFF - ON - OFF - ON .
  2. Count the number of times the MIL (check engine lamp) on the instrument panel flashes on and off.

The number of flashes represents the trouble code. There is a short pause between the flashes representing the 1st and 2nd digits of the code. Longer pauses are used to separate individual 2-digit trouble codes.
An example of a flashed DTC is as follows:


Lamp flashes 4 times, pauses, then flashes 6 more times. This denotes a DTC number 46. Lamp flashes 5 times, pauses, then flashes 5 more times. This indicates a DTC number 55. DTC 55 will always be the last code to be displayed.


0900c1528007935b.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 2: Diagnostic trouble code chart (1 of 2)-1995-97 engines


0900c1528007935c.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 3: Diagnostic trouble code chart (2 of 2)-1995-97 2.0L engines

Jul 26, 2012 | 1995 Dodge Neon

1 Answer

What part do i need to repalce


Hi Cornejo:
The DTC (Diagnostic Trouble Code) P0700 code is not the actual code that is of concern. The P0700 code is stored in the engine computer.

This code means that there is a code stored in the Transmission computer. The trans computer sends a message to the engine computer that there is a trans code stored. This lets the engine computer turn on the "check engine" light.

You need to have the transmission computer scaned for codes to find out whats going on. Most code readers do not read trans codes, you need to have a scan tool that is able to do this.
This could mean almost any thing. Most trans codes are eletrical related with the allison transmission.
Here is the diagnosis chart for the P0700. Again, this code only means a trans code is set in the TCM, not a actual failure code.
--------------------------------------------------------------------------------------------------------
DTC P0700
Circuit Description
This diagnostic trouble code (DTC) indicates that a related transmission DTC set in the transmission control module (TCM). The engine control module (ECM) receives the TCM DTC information over the serial data circuit. The ECM turns ON the malfunction indicator lamp (MIL) when the TCM sends a message over the serial data circuit requesting MIL illumination.

2_15_2012_1_58_02_pm.gif

Conditions for Clearing the DTC graphic
The control modul turns OFF the MIL after 3 consecutive ignition cycles that the diagnostic runs and does not fail.
A current DTC, Last Test Failed, clears when the diagnostic runs and passes.
A scan tool can clear the code from TCM history. The TCM automatically clears the DTC from TCM history if the vehicle completes 40 warm-up cycles without failure.

1. Verify power and ground supplies to the TCM when the vehicle is cold.

2. If OK, depending on ambient temperature. If ambient temperature is high and the problem will not show, remove the TCM and place it in a freezer for a couple of hours.
3. If the ambient temperature is low remove the TCM to a warm area for a couple of hours.
4. After sufficiently cold or warm, install the TCM and drive the vehicle immediately.
5. If the ambient temperature is low and the transmission now shifts or the ambient temperature is high and the transmission will not shift replace the TCM.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day

Feb 15, 2012 | Chrysler Town & Country Cars & Trucks

1 Answer

Received code P1400 engine light on what would cause this code?


GMC Truck Envoy - 2WD ' Envoy, Rainier, TrailBlazer, Ascender (VIN S/T) Service Manual ' Document ID: 1655997

DTC P1400
Diagnostic Instructions
• Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
• Review Strategy Based Diagnosis for an overview of the diagnostic approach.
• Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptor:
DTC P1400: Cold Start Emission Reduction Control System

Circuit/System Description
The catalytic converter must be warmed to efficiently reduce the emissions. The cold start strategy is to reduce the amount of time it takes to warm the catalytic converter. During a cold start, the engine idle speed is elevated and spark timing is retarded to allow the catalyst to warm quickly. This diagnostic monitors the following to build an exhaust energy model:

• Engine speed
• Spark advance
• Throttle position
• Engine airflow
• Engine coolant temperature
• Engine runtime
• Park/neutral position
• Vehicle speed

The actual model is then compared to the expected exhaust energy model.

Conditions for Running the DTC
• A cold start has been detected.
• The vehicle speed is less than 2 km/h.
• The engine is at idle with no input from the accelerator pedal.
• The airflow per cylinder is greater than 80 mg/cylinder.
• DTCs P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0220, P0222, P0223, P0201, P0202, P0203, P0204, P0205, P0206, P0300, P0335, P0336, P0351, P0352, P0353, P0354, P0355, P0356, P0502, P0506, P0507, P0601, P0602, P0603, P0604, P0606, P0607, P062F, P0641, P0651, P1101, P1516, P1682, P2101, P2119, P2120, P2122, P2123, P2125, P2127, P2128, P2135, P2138, P2176, P2610 are not set.
• This DTC runs for 15 seconds within the first 70 seconds of start up. This diagnostic runs once per trip when a cold start has been determined.

Conditions for Setting the DTC
The actual exhaust energy model does not match the expected exhaust energy model.

Action Taken When the DTC Sets
• The control module illuminates the malfunction indicator lamp (MIL) when the diagnostic runs and fails.
• The control module records the operating conditions at the time the diagnostic fails. The control module stores this information in the Freeze Frame/Failure Records.

Conditions for Clearing the MIL/DTC
• The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail.
• A current DTC, Last Test Failed, clears when the diagnostic runs and passes.
• A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic.
• Clear the MIL and the DTC with a scan tool.

Diagnostic Aids
Any loading of the engine that lowers engine RPM, such as with partial application of the clutch, during the first 70 seconds of engine run time may set this DTC.
Circuit/System Verification
Allow the engine to cool. Monitor the Cold Startup parameter. This should indicate Yes. Start and idle the engine for at least 2 minutes. DTC P1400 should run and pass.

Circuit/System Testing
• Inspect the air intake system for the following:
- If any other DTCs are set, diagnose them first. Refer to Diagnostic Trouble Code (DTC) List - Vehicle.
- Modified, damaged, or restricted
- Dirty or deteriorating air filter element
- Crankcase ventilation system for correct operation--Refer to Crankcase Ventilation System Inspection/Description.
- Water intrusion
- Vacuum leak and other un-metered air downstream of the mass air flow (MAF) sensor
- Intake manifold leak

• Inspect the exhaust system for the following:
- Water intrusion
- Exhaust leak
- Damaged, restricted, modified or enhanced exhaust system--Refer to Symptoms - Engine Exhaust .


Hope helps; keep us updated

Jun 30, 2011 | 2006 Chevrolet Trailblazer Ext

1 Answer

Temperature gauge not working


Yep!... take it back to the mechanic and tell him/her to recheck the system (there's no such DTC (Diagnostic Trouble Code) as "bad electrical connection"... somebody's pulling your leg!
Whenever the 'CHECK ENGINE' (Service Engine Soon) light comes on, the ECU (Engine Control Unit) sets a Diagnostic Trouble Code (DTC). These codes identify the particular engine management system which caused the light to come on.
You'll need to use/find an OBDII (On-Board Diagnostic) Scanner to retrieve any code(s) which may have been stored in the ECU computer. Afterward, we might be able to help you DIAGNOSE the problem and perhaps eventually fix the problem.

Oct 03, 2009 | 2004 Hyundai Elantra

1 Answer

Code-12 (VAF)


GOOD! I assume the CHECK ENGINE (yellow) light comes on!... correct? Whenever the "Check Engine" light comes on, there is always a DTC (Diagnostic Trouble Code) stored in the ECM (Engine Control Module). You'll need an OBDII (On-Board-Diagnostics) scanner to retrieve any codes recorded/set in ECM. Once you do this and let us know what, if any codes are set, then we can go from there.

Jun 24, 2009 | 1994 Hyundai Excel

Not finding what you are looking for?
2003 Chevrolet Blazer Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8274 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...