Question about 2007 Toyota 4Runner
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
ok, then the lock actuator is most likely seized, if you need instructions to repair, let me know, you have to get the part first, this will be a dealer item most likely. Then it's pretty simple. Remove the interior panel on the liftgate, you will see the latch and lock assembly, and a rod coming from it,the rod leads to the actuator. remove the rod, the retaining screws for the actuator, the electrical connector and then reverse for installation. Any issues let me know.
Posted on Mar 15, 2009
This is extremely common!
The micro-switch inside the glass hatch release is faulty, telling the door that it is partially depressed, thus shutting down opening for safety reasons.
You can verify this by opening the glass hatch (there is a access panel at the bottom of the door on the inside), removing the trim cover from behind the glass handle (two philips screws and one plastic push in fastener), then unplugging the glass handle.
Your door will now function normally, but without glass opening ability until you replace the handle.
The handle only takes a few 10mm nuts to remove and can be changed in a few minutes. It retails for around $35 from your dealer.
Posted on Sep 09, 2009
First, take off the license plate.
Since the hatch wouldn't open, I started from the inside and took down the top trim piece. After that the two side pieces come down, then the main trim piece which covers the bulk of the door comes out. These are all popped in with the white tabs.
There are 3 access hole covers to pop out (don't forget to install them back in when done) and through the left hole you can see the mechanism to unlatch, press it down with a screwdriver and open the door. If anytime you close the door you will have to do this to unlatch, up until you disconnect the cable and pull out the handle, then you have to locate the cable and pull that directly.
Behind the large trim piece you will find a metal access cover, remove the 7 or 8 10mm bolts holding that on and pop the 3 white tabs and let it hang off to the side. Disconnect the cable from the handle assembly by reaching in from the right hand side and popping of the cable from the handle assembly.
From the left and right access holes, locate the two 10mm nuts which hold the license plate assembly to the door and remove them. Then there are 4 plastic tabs that come in from the outside that hold the license plate assembly on in each corner, try and locate those and using some pliers squeeze them together and push it through. Next locate the license plate lamps wire connector and release that from the left side, it’s the simple push in and pull out square white connector.
After these are out, put back in 1 or 2 bolts into the large metal access cover so the hatch can be lowered (don’t close it).
Here is where I had fun, begin to pop out the assembly that it was bolted to. I ended up breaking 3 of the 4 plastic tabs in each corner because I did not use pliers from the other side to pull them out, however it remained somewhat useable (hindsight 20/20).
Now the license plate assembly can be taken to a bench to replace the handle assembly (Toyota doesn't sell just the handle, it is a small assembly). Two screws out and the assembly is replaced.
Before pressing the license plate assembly back onto the truck, make certain all the plastic tabs are in the assembly and not in the truck. Reverse the process to re-install.
Posted on Dec 12, 2009
Tips for a great answer:
Jun 21, 2016 | Cars & Trucks
Apr 12, 2016 | 2009 Kia Sportage
Feb 07, 2016 | Cars & Trucks
Feb 07, 2016 | 2003 Ford Expedition
Feb 09, 2015 | 2002 Toyota Sequoia
Sep 13, 2014 | 2002 Hyundai Santa Fe
Mar 02, 2014 | 2004 Chevrolet TrailBlazer
Aug 14, 2012 | Cars & Trucks
Aug 12, 2009 | 2005 Jeep Liberty
244 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: