Question about 1995 Toyota Camry

2 Answers

My idle drops everytime i come to a complete stop and even when i put it into reverse and also sometimes the car shuts down...

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 6,826 Answers

Idle Air Control (IAC) Valve OPERATION The ECM is programmed with specific engine speed values to respond to different engine conditions (coolant temperature, air conditioner on/off, etc.). Sensors transmit signals to the ECM which controls the flow of air through the bypass of the throttle valve and adjusts the idle speed to the specified value. Some vehicles use an Idle Speed Control (ISC) valve while others use an Air Valve (AV) or Idle Air Control (IAC) valve to control throttle body by-pass air flow. TESTING 2S-ELC Engine

  1. With the engine running and the coolant temperature below 140°F (60°C), pinch off the Air Valve hose and verify that the idle is reduced by no more than a 100 rpm.
  2. Unplug the valve wire connector and measure the coil resistance with an ohmmeter. It should be 40-60 ohms with the coolant temperature at 176°F (80°C) and the air valve closed.
  3. If not as specified, replace the valve. 3S-FE and 5S-FE Engines NOTE: The idle speed must be set correctly before testing the ISC valve.
  4. Bring the engine to normal operating temperature with transmission in N.
  5. Using a jumper wire, connect the terminals TE1 and El of the check connector (DLC 1). Fig. 1: Attach a jumper wire to the terminals TE1 and E1 in the DLC 1 my idle drops everytime i - 89554g46.gif

  6. The engine rpm should rise to 900-1300 rpms for 5 seconds. Check that it returns to idle speed. If rpm is as specified, the valve is functioning properly.
  7. If rpm did not function as specified, stop the engine and disconnect the jumper wire.
  8. Disengauge the ISC valve connector.
  9. Using an ohmmeter, measure the resistance between the +B terminal (middle terminal) and the ISC1 - ISC2 (3S-FE) and the ISCC - ISCO (5S-FE) outer terminals. Fig. 2: Attach an ohmmeter and measure the resistance between the three terminals - 3S-FE engine 89554g49.gif
    Fig. 3: Attach an ohmmeter and measure the resistance between the three terminals - 5S-FE engine 89554g47.gif

  10. The resistance should be 16-17 ohms on the 3S-FE engine and 19.3-22.3 ohms on the 5S-FE engine.
  11. If not as specified, replace the ISC valve.
1MZ-FE Engine NOTE: The idle speed must be set correctly before testing the valve. Make sure the A/C is off during testing. Fig. 4: The IAC valve is attached to the lower portion ofmy idle drops everytime i - 89554p46.jpge body 89554p46.jpg
  1. Bring the engine to normal operating temperature with transmission in N.
  2. Using a jumper wire, connect the terminals TE1 and El of the check connector (DLC 1).
  3. The engine rpm should rise to 1000 rpms for 5 seconds. Check that it returns to idle speed. If rpm is as specified, the valve is functioning properly.
  4. If rpm did not function as specified, stop the engine and disconnect the jumper wire.
  5. Disengage the ISC valve connector.
  6. Using an ohmmeter, measure the resistance between the +B terminal (middle terminal) and the RSC and RSO outer terminals. Fig. 5: Attach an ohmmeter and measure the resistanmy idle drops everytime i - 89554g48.gifhe three terminals - 1MZ-FE engine 89554g48.gif

  7. The resistance should be 21-28.5 ohms on a hot engine.
  8. If not as specified, replace the ISC valve.
2VZ-FE and 3VZ-FE Engines
  1. Disengage the ISC valve connector.
  2. Using an ohmmeter, measure the resistance between the B1 terminal (lower middle terminal) and the S1 or S3 (lower outer terminals), and between B2 terminal (upper middle terminal) and the S2 or S4 (upper outer terminals). my idle drops everytime i - 89554g50.gifig. 6: ISC terminal identification - 2VZ-FE and 3VZ-FE engines 89554g50.gif

  3. If the resistance is not 10-30 ohms, replace the ISC valve.
  4. Apply battery voltage to terminals B1 and B2 while repeatedly grounding S1, S2, S3, S4, S1 in sequence. Check that valve moves toward the closed position. my idle drops everytime i - 89554g51.gifing the IAC using battery voltage to see if the valve will close-2VZ-FE and 3VZ-FE engines 89554g51.gif

  5. Apply battery voltage to terminals B1 and B2 while repeatedly Grounding S4, S3, S2, S1, S4 in sequence. Check that valve moves tmy idle drops everytime i - 89554g52.gifened position. Fig. 8: Testing the IAC using battery voltage to open the valve - 2VZ-FE and 3VZ-FE engines 89554g52.gif

prev.gif next.gif

Posted on Oct 12, 2010

Testimonial: "thanks alot!!!!!!!"

  • Duane Wong
    Duane Wong Nov 05, 2010

    Thanks for the rating and hope you can repair your vehicle's stalling problem.

  • Duane Wong
    Duane Wong Nov 05, 2010

    Also, if you check the engine codes, does it have any stored?

×

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

If I mileage clean the EGR valve mounted on the trottle body ,clean were it is conected to throttle body and egr valve can be cleaned with carborator cleaner. If this does not help check the Trottle position sensor.I have a 1995 toyota camry that did what you just described, hope this helps!!

Posted on Nov 05, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Code po401


Sometimes the intake manifold gets carbon in it from a bad egr valve. You may need to pull the EGR and see if you cant clean it a little.

Oct 19, 2013 | Cars & Trucks

1 Answer

The idel on my 1992 chevrolet lumina 3.1 euro goes high then drops down low in park or in gear what is problem


Could becaused by a few different thing's . Map sensor , idle air control valve , a vacuum leak . Having the vehicle's scan data viewed would probably pin point the problem . Do you know what scan data is ? Is what a professional tech uses to find problems .
084 Engine Mechanical Tests Scan Data for Vacuum Leak
007 Idle Speed Problems Scan Data for Idle These kind of test's are what seperate week end DIY'ER's from a professional tech.

Jul 01, 2017 | 1992 Chevrolet Lumina

1 Answer

Galant vrg-gdi-when i engage reverse the car stalls--but once you start moving --ok


You vehicle uses a Idle air control motor,(IAC) when you put a load on the vehicle (Drive or reverse) the ECM detects the load and idles up the IAC, even for the A/C (air conditioner) You can try a throttle body cleaning. or a new IAC

Mar 01, 2012 | Cars & Trucks

1 Answer

87 thunderbird some times starts but quits when put into geer


check your contact points are set correctly, or may even be burned , if so replace them , its a comon thing if the contact points are badly set ,when you put the car in gear it will stall or wont idle , i had a 67 t/bird landau that did exactly the same , , turning off the highway was a night mare ,i had to keep the accelerator pressed while i braked , otherwise it would stop and then i would have no steering ,very annoying and very dangerous

Feb 16, 2012 | 1987 Ford Thunderbird

1 Answer

Engine shut down when on auto reverse mode once i move my car on reverse and apply break to make it stop the engine totally shut down even though i adjusted the idle...


Hi,

Please check your reverse gear wiring for malfunction. It can be shorted with others that lead your car dies.

Regards

Oct 05, 2011 | 1996 Mitsubishi Galant

1 Answer

2003 Chevy Cavalier 2.2L - RPMs Surge & Drop Out - Stalls In Idle


it sounds like its drawing air into the inlet mannifold

Apr 16, 2010 | 2003 Chevrolet Cavalier

1 Answer

Engine shuts off when I put it on Reverse !


Idle may be too low. A lock screw is at the back of the P7100 mechanical engines, or 12 valve engines. If VP44 or 24 valve you need a dealer to change idle in the ecm. good luck...

Apr 03, 2009 | 2006 Dodge Ram 2500

1 Answer

IAC Solenoid


Buy a can of spray carb/throttle body cleaner from a parts store and clean the throttle valve butterfly and IAC aka idle speed control motor, do this with the engine running, you will have to hold the idle hi to perform this or it will stall, use at least 1/2 can of cleaner, then shut down and disconnect the battery for 5 minutes, reconnect and drive a few days to let the PCM relearn you driving habits.

Jun 10, 2008 | 1999 Land Rover Discovery

Not finding what you are looking for?
1995 Toyota Camry Logo

1,696 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...