Question about 2000 Ford F250 Super Duty Crew Cabs

Open Question

Remove and replace front wheel bearings on a 4 wheel drive

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 24 Answers

SOURCE: replace front wheel bearings

The bearings in your car are pressed into a hub. If the part is available as an assembly, it can be replaced that way. Generally on a front drive car:
Remove wheels and brake calipers
If it is pressed in: remove the rotors, disconnect the drive shafts and remove the steering knuckle. Then the old bearing is pressed out and the new one pressed in with a machine shop press. If the bearing is part of the hub, that will be unbolted and the new one swapped.

On a scale of 1-10 difficulty, Id rate it a strong 7

Posted on Jun 20, 2008

Ad
  • 3 Answers

SOURCE: wheel bearing

u have to take the hub off. and press the wheel bearing out. it takes alittle time to do bc u have to take your rotor and brake assembly off to get to the hub.

Posted on Jun 25, 2008

SOURCE: need to replace the front

You need to remove the tire, brake caliper and rotor. Remove the axle nut and hub bolts. Take the hub (bearing is pressed in it) to a machine shop to have new bearings pressed in.

A mechanic will usually charge around 300 dollars per bearing (cost included).

Posted on Aug 06, 2008

alicantecoli
  • 22265 Answers

SOURCE: 2002 ford explorer front wheel bearing assembly

remove hub ,take retaining circlip out and knock it out with a big big hammer supporting it on an old wheel rim and a tree trunk.this job is easy to do but unless you have the right tools entrust it to a garage who will have a nice press .

Posted on Feb 02, 2009

daves944
  • 1050 Answers

SOURCE: 2003 Pontiac Montana Front Wheel Bearings

Remove the wheel, remove the hub nut, remove the brake caliper and rotor, put your socket and extension through the hub flange onto the bearing retainer bolts, undo them, release the abs sensor connector if it has it, remove the bearing and hub flange as an assembly, put the new one on and go backwards from here. Torque the hub nut to 180 ft/lbs, your done.

Posted on Apr 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is it possible to remove and replace front wheel bearings with out a press


In order to remove the front wheel bearings without press hub off the bearing and then the bearing out of the knuckle. To do the first step need a a Support Bridge.It is a special tool. Make bridge and use a general bearing pulled kit to replace bearings. use a "Front Wheel Drive Bearing Removal Adapters Puller Pulley Tool Set Kit" .To replace the bearing, remove front CV shaft taking care not to move the CV shaft too far out .

Nov 06, 2015 | 2002 Kia Rio

1 Answer

How to replace wheel bearing on 1996 ford explorer


Is it a 2 wheel drive of 4 wheel drive explorer?? I'm going to take a shot in the dark and go with 4x4. Remove the cotter pin and axle nut. Then jack up and brace the vehicle. Remove the front tire (since you said wheel bearing and not axle bearing), caliper, caliper bracket, and the three bolts on the back of the spindle that hold in the bearing and hub. Slide the hub and bearing out. May take a couple of taps with a hammer.

Nov 26, 2010 | 1996 Ford Explorer

1 Answer

How to replace rear wheel bearing on 1994 bmw 325i


3-Series (Except M3, M Roadster, M Coupe, 318ti & Z3)

1. Raise and support vehicle. Remove wheel(s).
2. Remove axle shaft. See appropriate AXLE SHAFTS article.
3. Remove brake disc. See BRAKE DISC .
4. Screw special tool (33 2 116) onto drive flange with wheel studs. Drive out drive flange with special tool (33 4 201/202/203). See Fig. 33.
5. If necessary, pull off bearing inner race using special tool (00 7 500) and a thrust piece. See Fig. 34.
6. It may be necessary to remove inner wheel bearing race with the following procedure:
  • Detach wheel bearing inner race with special tool (33 4 400) through groove in bearing inner race.
  • According to outside diameter of bearing inner race, use special tool 33 4 401 with: 33 4 405 for dia. 45-51 mm, 33 4 406 for dia. 50-55 mm and 33 4 407 for dia. 55-61 mm in groove. See Fig. 35.
  • Tension special tool 33 4 401 with wrenches 33 4 403 and 33 4 404 until it can still just be turned in groove. See Fig. 36 .
  • Screw in special tool 33 4 402. Detach inner bearing race.
7. Remove circlip. See Fig. 37 .
8. Remove wheel bearing with special tool 33 4 031/ 041/ 042/ 043/ 045. See Fig. 38 .

CAUTION: Do not reuse old wheel bearing.

9. Draw in new wheel bearing with special tool 33 4 041/ 042/ 043/ 047. For inner bearing race 42 mm use special tool 33 4 049 and for 39 mm use 33 4 046. See Fig. 39 .
10. Installation is reverse of removal.
11. Replace stretched or damaged circlip. Ensure correct seating.
12. Pull in drive flange using special tool 33 4 041/ 042/ 043/ 045/ 048. See Fig. 40 .
13. Install brake disc.
14. Install axle shaft.


91stt_11.jpg

91stt_12.jpg

91stt_13.jpg

91stt_14.jpg

91stt_15.jpg

91stt_16.jpg

91stt_17.jpg

91stt_18.jpg

Nov 12, 2010 | BMW 325 Cars & Trucks

1 Answer

REMOVAL OF FRONT WHEEL BEARINGS


Front (4 Wheel Drive) To Remove:
  1. Raise and support the vehicle
  2. Remove or disconnect the following:
    • Tire and wheel assembly
    • Rotor (See: Disc Brake Rotor)
    • Wheel speed sensor and brake hose mounting bracket bolt from the steering knuckle
    • Electrical connection for the wheel speed sensor
    • Front drive halfshaft assembly (See: Halfshaft)
    • Hub and bearing assembly mounting bolts 4WD front hub 9308kg35.gif

    • Hub and bearing assembly
To Install:
  1. Clean all corrosion or contaminates from the steering knuckle bore and the hub and bearing assembly
  2. Lubricate the steering knuckle bore with wheel bearing grease or the equivalent
  3. Install or connect the following:
    • Hub and bearing assembly
    • Hub and bearing assembly mounting bolts and tighten the hub to knuckle bolts; Torque to: 133 ft. lbs. (180 Nm)
    • Front drive halfshaft assembly (See: Halfshaft)
    • Electrical connection for the wheel speed sensor
    • Wheel speed sensor and brake hose mounting bracket bolt to the steering knuckle and tighten the bolt; Torque to: 106 inch. lbs. (12 Nm)
    • Rotor (See: Disc Brake Rotor
    • Tire and wheel assembly
    Wheel lug nut tightening sequence gm_trk_sub15_wheel_lug_nut_tight_seq.gif

  4. Torque the lug nuts to specification
  5. Test drive the vehicle to confirm the repairs
prev.gif next.gif

Aug 03, 2010 | 2001 Chevrolet Silverado 1500

2 Answers

Replace front left wheel berring on 2002 GMC Yukon


do not replace only the bearing. replace hub assembly. remove rim/tire , remove caliper, mounting plate, rotor. . un bolt hub assembly, unplug abs. remove front axle nut if 4x4. you may need to rent the axle nut remove kit and hub puller. pull out hub. drive axle reward out of hub. install new part. do not torque hub over 90lbs. check with parts sell for spec

Jan 03, 2010 | 2002 GMC Yukon XL

1 Answer

How do you remove the backing plate from an '05 Chev Venture rear hub so the hub can be replaced?


The 4 Bolts that Hold the HUB in Also Hold the Backing Plate
Hub Replacement - Rear (Front Wheel Drive/Drum)

Removal Procedure
  1. Raise and support the vehicle.
  2. Remove the tire and wheel.
  3. Remove the brake drum.
    1. Remove and DISCARD the wheel bearing/hub bolts.
    2. Remove the wheel bearing/hub.
    3. Disconnect the wheel speed sensor electrical connector (2).Installation Procedure
    4. Connect the wheel speed sensor electrical connector (2).
      1. Install the wheel bearing/hub. Caution: These fasteners MUST be replaced with new fasteners anytime they become loose or are removed. Failure to replace these fasteners after they become loose or are removed may cause loss of vehicle control and personal injury. Notice: Refer to Fastener Notice in Service Precautions.
      2. Install the NEW wheel bearing/hub bolts.
      1. Install the brake drum.
      2. Install the tire and wheel.
      3. Lower the vehicle.

Nov 07, 2009 | 2005 Chevrolet Venture

1 Answer

How do you remove front wheel bearing


is this front wheel? rear wheel? or 4 wheel drive? if you have front wheel drive or 4 wheel drive you will need to take the tire off and get the center cap off with cotter pin on most vehicles. then put the tire back on without its center cap. then put the vehicle back on the ground. then use required socket with an extention and breaker bar to put through the rim to loosen center hub bolt about a quarter turn. just enough to break it loose. then take the tire back off to finish the job. remove the brake caliper and rotor then center nut on hub bearing. there should be 3 bolts from the inside holding hub bearing on. on rear wheel only you won't need to take the tire off and on.

Oct 08, 2009 | 2000 Honda CR-V

1 Answer

Replace front rotors on 2002 4 wheel drive


I am not an expert but yes i beleive you have to remove hub nut to get rotor off,also will need flat head screwdriver to unscrew internal nut before bearing.I also changed bearings while i had it all loose.

Aug 03, 2009 | Mitsubishi Montero Sport Cars & Trucks

2 Answers

Replacing front drive axle universal joints.


remove front wheel brakes,rotors, axle nut,remove the four bolts on the bake side of your unit bearing using one of the 4 bolts removed from the unit bearing (also knowin as wheel bearing) go get a half dozen of the same bolt only 1 to 2 inchs longer theard them into the unit bearing from the back side and start beating. the unit bearing is a sob to get out but will come out with time once you get it out pull out your axle shaft replace the ujoint and reassemble anti seize everything as you re assemble it

Jul 09, 2009 | 2004 Dodge Ram 2500

1 Answer

Replace front wheel bearings


The bearings in your car are pressed into a hub. If the part is available as an assembly, it can be replaced that way. Generally on a front drive car:
Remove wheels and brake calipers
If it is pressed in: remove the rotors, disconnect the drive shafts and remove the steering knuckle. Then the old bearing is pressed out and the new one pressed in with a machine shop press. If the bearing is part of the hub, that will be unbolted and the new one swapped.

On a scale of 1-10 difficulty, Id rate it a strong 7

Jun 20, 2008 | 1998 Nissan Sentra

Not finding what you are looking for?
2000 Ford F250 Super Duty Crew Cabs Logo

Related Topics:

132 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77194 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

fordexpert

Level 3 Expert

5579 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...