Question about 1997 Chevrolet Suburban

Open Question

How to change the motor mounts on a 1997 chevy suburban?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76846 Answers

SOURCE: need steps to reprogram chevy suburban 1997 keyless entery

1. Locate the Data Link Port. It is located under dash drivers side. Be sure you know
which pins are 8 and 4.


(Note port is wider at top) Your OBDII port will not
have numbers, use the for reference.

obd-1.jpg





2. Make sure there are metal contact pins in terminals 8 and 4. Connect 8 to 4 with a
suitable jumper wire (leave the jumper wire connected throughout the programming
procedure). Make sure you know which terminals are 8 and 4. The vehicle will respond
by locking and unlocking the
doors to signify entering of programming mode.

3. Press and hold both the LOCK and UNLOCK buttons together on the first transmitter to
be programmed. After about 15 seconds, the vehicle will respond by locking and
unlocking the doors. Release the buttons on the transmitter.

4. Within one minute, repeat the previous step on the remaining transmitters to be
programmed.

5. Remove jumper wire applied to the OBDII Port.

Posted on Feb 10, 2009

Ad
  • 5 Answers

SOURCE: 1988 chevy suburban shakes at 55mph and up..

sounds like shot tie rods or possibly pitman arms

Posted on Mar 13, 2009

  • 64 Answers

SOURCE: HOW DO YOU CHANGE REAR BREAK PADS ON A 1997 CHEVY SUBURBAN?

Unlike the front pads where you only have to push the caliper piston in to replace the pads,the rear caliper pistons have to be turned clockwise to screw them back in.Hint: only go as far as nessesary to get the pads to clear the rotor as this is also the adjustment for the emergency brake.Good luck,
ChevRev

Posted on Mar 28, 2009

maecarla
  • 3 Answers

SOURCE: I have a 1997 suburban with no brake lights I

I replace the brake switch also and it didn't work. Eventually what I did was open the old brake switch and remove the contacts inside. I cleaned them and put them into the new switch. Oddly that worked.

Posted on Jul 18, 2009

  • 288 Answers

SOURCE: Chevy Suburban 1997 1500 won't start when Cold

it could be a tune up issue such as plug wires plugs . but my guess is its a computer engine temp sensor if it reads 5 degrees out of range it cuold give you a hard start or a no start problems the best way to look at this problem is with a scan tool when it is cold to see if the temp matches outside ambeint air temp 1 or 2 degrees ok b ut not 4 to five there is a nother way to check it buy useing dvom at a temp to omhs chart.

Posted on Jan 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove transmission from a 1997 chevy suburban 4x4


Jack up and block under the front wheels about a foot off the ground Go underneath and remove the rear transmission mount cross bar and drive shaft lower down the transmission enough to get at the bell housing mount bolts Remove them and the 4 torque mount bolts use a floor jack and roll the trany back and out

May 22, 2015 | 1997 Chevrolet Suburban

1 Answer

1997 chevy suburban front blower issue.... doesn't work unless a gust of wind or I hit a bump. wondering what part I need for it to work.


it may be either a bad connection at the resistor block or the blower motor. check this out. if going over a bump starts the motor it may be a bad blower motor that needs replacing.

Sep 14, 2014 | 1997 Chevrolet Suburban

1 Answer

97 chevy suburban won't start I believe it is


does the motor crank when key is turned?If so check for a spark at the plugs.Get an auto electrician bypass your alarm

Mar 22, 2012 | 1997 Chevrolet Suburban

1 Answer

I have a chevy suburban 97 the wiper motor stop working when a hit it start working then stop again


It needs a new contact circuit board, it's held onto the wiper motor assembly by 3 torx type screws. It has the brushes built into it. You can get one from any autoparts store.

Feb 13, 2011 | 1997 Chevrolet Suburban

1 Answer

How do I change oil cooling lines on 1994 Chevy suburban?


The best way would be from underneath, at the back of the block, on the driver side, remove the two bolts holding the oil line assembly to the block. Unbolt the oil line bracket at the front of the motor mount, remove the lines from the radiator. Then remove the lines from where they attach to the assembly.

Apr 08, 2010 | 1994 Chevrolet Suburban

1 Answer

My 1997 chevy suburban's windshield wipers don't work all the tim


It sounds as though the grounding ******** your wiper motor is not making a good ground therefore the wipers are not coming to the exact parking position. By pulling on them you pass that position and they begin to operate correctly. Thank you, Dana

Mar 26, 2010 | Chevrolet Suburban 1500 Cars & Trucks

1 Answer

Where is the valve idle air control on 1996 chevy suburban


if you follow the air cleaner/filter tube to where it meets the motor you will find the throttle body and it is mounted in the throttle body on the opposite side of where the gas pedal cable mounts. it has a 4 wire plug i believe.

Dec 27, 2009 | 1996 GMC Suburban

1 Answer

I have two cilynder heads crack on my 1999 gmc suburban i but a motor from 1997 chevy van they both vortec are they the same cilyder heads


yes,as long as the years are the same ,or close,look for mounting brackets,and such to be the same,

Dec 09, 2009 | 1999 GMC Suburban

1 Answer

1988 chevy suburban shakes at 55mph and up..


sounds like shot tie rods or possibly pitman arms

Mar 13, 2009 | 1988 Chevrolet Suburban

Not finding what you are looking for?
1997 Chevrolet Suburban Logo

Related Topics:

181 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6924 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...