Question about 2003 Mercury Mountaineer

1 Answer

Need to put up power window on mercury montaineer until switch comes in

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,533 Answers

You maybe able to jumped the wires to get the window to come up until the switch comes in give these websites a try www.alldatadiy.com and www.autozone.com if all fails stop by your local library and get your hands on a Haynes auto repair manual for your SUV wish you the best of luck Michigan Man.

Posted on Oct 12, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1997 mercury sable gs, and the drivers window wont go up. Its power window, and I've had this happen before, and played with the window lock switch, and it would work again, but not this time


pull out the set of 4 switches and switch the wires from that window to a different switch to raise it then put the wires back in place and put switch panel back

May 21, 2015 | 1997 Mercury Sable

1 Answer

How should you add fluid to your transfer case in mercury montaineer


There is video on it

Noise doesn't have to come from transfer case

You have to find the noise

Transfer case fluid should have been changed along
with all fluids,years ago.

No Preventative Maintenance Plan there ?
No Log Book of what never gets done !!

Aug 09, 2014 | 2008 Mercury Mountaineer

1 Answer

Cylinder_diagram_location_2002_mercury Montaineer V8 AWD


1,2,3,4, Passenger Side
5,6,7,8, Driver Side


1&5 are at the front of motor

Jan 23, 2013 | 2002 Mercury Mountaineer

1 Answer

I need fuse bx information for 98 mercury montaineer i don't have owners manual to check fuse diagram my abs light comes on and i have power going to factory towing package


If the abs light comes on than the fuses are good. If the abs light did not come on when you turned the key on than I would be suspicious of a fuse or relay failure. The first thing you need to do is have the abs module scanned for codes. You local auto parts store may do this for you for free otherwise you can either spend a couple hundred dollars on an abs scan tool or pay for an abs diagnostic charge at your local auto shop. Once you know what code or codes are causing the light to come on you will have a much better idea opt what the problem is. To things that will help you out. 1. If the abs light comes on when you start the car and then goes out until your start to drive than it is likely you have a speed sensor that is going bad, or possible a wheel bearing that is getting sloppy and causing excessive air gap. 2. If the light comes on and never goes out than the abs system is failing it's self test. The first thing I would do is ohm check all four wheel speed sensors (1998 might only have three, one on each front wheel and one in the rear differential). If one is open or low on resistance than it is bad. Hope that helps.

Jul 03, 2011 | Mercury Mountaineer Cars & Trucks

1 Answer

I need a diagram of the firing order for a 1997 montaineer


For the 1997 Mercury Mountaineer V8 5.0L Engine:

Firing Order:
1-3-7-2-6-5-4-8

Cylinders:
.......(back)......
|..4..|........|..8..|
|..3..|........|..7..|
|..2..|........|..6..|
|..1..|........|..5..|
.......(front)

Ignition Coil Connections:
(back)........(back)
|.4..7.|........|.3..5.|
|.8..2.|........|.6..1.|
(front)........(front)

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

May 01, 2010 | 1997 Mercury Mountaineer

1 Answer

How to change upper ball joint in 2000 mercury montaineer


I will tell you that you need to go to a parts store that lends out tools because you need a special compressor for that year

Feb 26, 2010 | 2000 Mercury Mountaineer

1 Answer

Transmission plug


doesnt have one ,drop the sump pan

Jan 12, 2010 | 2004 Mercury Mountaineer

1 Answer

1997 mercury montaineer radio


turn off the headphone switches located near the passenger seats. also make sure the headphones are all unplugged.

Dec 04, 2008 | 1998 Mercury Mountaineer

Not finding what you are looking for?
2003 Mercury Mountaineer Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

fordexpert

Level 3 Expert

5470 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...