Question about 1992 Toyota 4Runner

1 Answer

I just need to know the tourque in pounds on the rear diff bolts

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 204 Answers

95 NM FOR GEAR BOLTS , 80 NM FOR CAPS BOLTS

Posted on Oct 12, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Transmission oil pan bolts tourque specification please


Depends on the gasket used, but 7 to 14 foot pounds. I just snug them up with a ratchet one hand.

Feb 18, 2015 | 2002 Toyota Sienna

1 Answer

How to remove rear diff from ve commodore?


loosen rear wheels, jack up rear so wheels are free, fit safety stands , drain oil, remove wheels, remove 4 bolts holding axle bearings. remove both axles, remove bolts from tail shaft at diff pinion flange , leave tail shaft in transmission housing or oil will leak out, remove bolts from diff housing, the diff center can now be removed.

Aug 28, 2014 | 1998 Holden VT Commodore

1 Answer

Tourque specs


torque the cylinder head bolts to eighteen (18) foot pounds (ft/lbs) in the sequence shown in the attached photo.
27b117e1-d4c4-4596-8a8a-f275444e8ed9.jpg

Dec 07, 2013 | 1995 Isuzu Pickup

1 Answer

Rear axle 02 escalade need to remove to replace dust shield


-chalk the wheels so the vehicle can not roll.
-Place the transmission in nuetral.
-jack up the rear of the vehicle.
-remove the real wheels-
-remove the drums or calipers and rotors.
-remove the rear diff fill plug on the side of the differential.
-remove the center cover on the rear differential. Have a drain pan under it to catch the lube that will come out.
-rotate the drive shaft until the rear diff pin bolt is accessible and remove the bolt.
-remove the rear diff pin
-push the axles in
-remove the c clips from the axles
-pull the axles out
-replace the backing plate/dust shield.

They do make a two piece backing plate that can be installed without removing the axles. You will unbolt the old backing plate then cut it into two pieces to remove. The new two piece backing plate will slide over the axle and then bolt into place. I know for sure NAPA has them.

If you have any questions let me know!

Oct 05, 2011 | Cars & Trucks

1 Answer

How many pouns i need to put on 96 bmw 318 is head bolts


ok its a little diffrent for this vehicle you have a 3 step prossess for each bolt as listed below
first tourqe all bolts to 22 ft pounds then when they are all tourqued to that ft pounds
then turn each bolt an additonal 90 degrees then after you do that to all the bolts you must turn them all another 90 degree and that is how tight they should be i was a bmw mechanic for 3 years i am not sure why they do it this way but it is the proper setup

May 05, 2011 | 1996 BMW 318

1 Answer

I need to replace oil pump on a 1988 ford bronco 2


Remove oil pan, making sure to drain oil first. Remove oil pump attaching bolts. Lift off oil pump and withdraw oil pump drive shaft.
INSTALLATION;
Prime the new oil pump by filling either the inlet or outlet port with engine oil. Rotate the pump shaft to distribute oil within the pump body. Insert oil pump drive shaft into block dwith the pointed end facing inward. The pointed end is closest to the pressed-on flange. Place oil pump into position with a new gasket and install attaching screws. Tighten the screws to 15-22 foot pounds of tourque. Clean and install the oil pump inlet tube and screen assembly with a new gasket. Tighten the bolts, then replace the oil pan.
Oil Pan;
Clean of any debris and replace gasket. Fit the oil pan bolts and tighten in two steps. Start from the rear/left hand side and tighten first, then tighten the bolt in the front/right side. Alternate from rear to front, working from back to front and front to back.

Oct 06, 2010 | 1988 Ford Bronco II

1 Answer

HOW DO I REMOVE REAR DIFF FROM MY 1994 LAND ROVER DISCO


Remove the halfshafts, the rear propshaft, the ring of bolts holding the diff in the axle and pull it out, drain the oil first.
But i must say, if you need help on how to remove the diff, then you obviously have no mechanical knowledge,, so what are you doing pulling out the diff. do you know how to repair and set up diffs ?

Feb 21, 2010 | 1997 Land Rover Discovery

1 Answer

Torque settings on a 1999


There are 2 different tranmissions in this vehicle. Make sure you know which one you have when selecting the torque settings. Do notice the 5R55E pan bolts are tightened in inch pounds. 4R70W Torque convert drain plug. 21-22 ftlb Pan bolts 9-11 ftlb 5R55E Pan bolts 115-133 inlb Ford Rear end Pan bolts 33 ftlb

Apr 05, 2009 | 1999 Ford Explorer

1 Answer

Need to know what tourque for the valve cover bolts, 97 tercel


10 foot/pounds. Hint from experience, change the gasket.

Dec 04, 2008 | 1997 Toyota Tercel

1 Answer

Tourque converter


The torque converter is a good sized round object bolted to the flywheel inside the bell housing.

Oct 11, 2008 | 1997 Ford F150 Regular Cab

Not finding what you are looking for?
1992 Toyota 4Runner Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...