Question about Toyota Camry

1 Answer

My camry produced a fault code for camshaft sensor and it was replaced.some moments after the engine light came again and it produced yet again the previous fault code for cam sensor.its a 2006 camry vvti with a 2az fe .

Posted by on

  • Anonymous Mar 13, 2014

    engine light goes on

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 14,036 Answers

YOU NEED CODE SCANNER TO ERASE CODE.

Posted on Oct 12, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Engine malfunction light


give us the codes that the engine light are on for and we may be able to give you a better idea of the problem
engine codes can cover many causes for the light report

Aug 01, 2016 | 2008 BMW 535i Sedan

3 Answers

What is wrong? cheapest fix


as these numbers are dodge fault codes ill assume that's what you have , both of these codes refer to a low to no oil pressure condition , this has several causes an can be as simple as low oil level to a bad sensor (behind alternator) to at worst a bad oil pump

since this is a oil pressure loss fault its stored as a major fault an will require a reset of ecm before it will allow a engine restart (after resolving problem) it does this to prevent engine failure for no lubrication

Dec 01, 2015 | Cars & Trucks

1 Answer

Where is the camshaft sensor on a 2012 camry


check if new engine is same old engine in all components,
if your engine is an 2az ,2.4L , the camshaft sensor its located on rear engine head , near the refrigerant outlet

May 12, 2017 | 2012 Toyota Camry L Sedan 2.5L 4-cyl....

1 Answer

Whats code po 343


Possible symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Lack/Loss of Power
- Engine Stall
P0343 Chevrolet Description
The Camshaft Position (CMP) Sensor sensor works in conjunction with a 1X reluctor wheel on the camshaft. The Powertrain Control Module (PCM) provides a 12 volt power supply to the CMP sensor as well as a ground and a signal circuit.
The CMP sensor determines whether a cylinder is on a firing stroke or on an exhaust stroke. As the camshaft rotates, the reluctor wheel interrupts a magnetic field produced by a magnet within the sensor. The sensors internal circuitry detects this and produces a signal which the PCM reads. The PCM uses this 1X signal in combination with the Crankshaft Position sensor 24X signal in order to determine crankshaft position and stroke. This diagnostic for the Camshaft Position sensor tests for a loss of Camshaft Position sensor signal.
Observe that as long as the Crankshaft Position sensor 24X signal is available, the engine will start. The PCM can determine top dead center for all cylinders by using the Crankshaft Position sensor 24X signal alone. The Camshaft Position sensor 1X signal is used by the PCM to determine if the cylinder at top dead center is on the firing stroke, or the exhaust stroke. The system attempts synchronization and looks for an increase in engine speed indicating the engine started. If the PCM does not detect an increase in engine speed, the PCM incorrectly synchronized to the exhaust stroke and will re-sync to the opposite cam position. A slightly longer cranking time may be a symptom of this condition.

Read more: http://engine-codes.com/p0343_chevrolet.html#ixzz31FPYjyRM

Mar 26, 2014 | 2002 Chevrolet Suburban

1 Answer

Camry engine shuts down


code p3190 refers to low engine power--malfunction. Possible causes ---intake system, fuel system---mechanical fault---Mass air flow sensor---engine coolant temperature sensor---crankshaft position sensor---camshaft position sensor --- ECM. I would start with the water coolant sensor as if it reads boiling it will shut down the engine.

Mar 18, 2013 | 2010 Toyota Camry

1 Answer

I went to scan my toyota yaris car and the following codes were give ; temperature ckt low input po117


EOBD II Error Code: P0117
Fault Location:
Engine Coolant Temperature (ECT) Sensor (G62) - Low Input
Possible Cause:
Malfunction Indicator Lamp (MIL) Triggered on first occurrence.
Coolant thermostat.
Wiring short to earth.
Engine coolant temperature (ECT) sensor.

EOBD II Error Code: P0340
Fault Location:
Camshaft Position (CMP) Sensor A (G40), Bank 1 - Circuit Malfunction
Possible Cause:
Malfunction Indicator Lamp (MIL) active.
Wiring from/to Camshaft Position Sensor (CMP) faulty.
Camshaft position (CMP) sensor faulty.
Timing misaligned.
Possible Solutions:
Check Wiring from/to Camshaft Position Sensor.
Check Camshaft Position Sensor.
Check Timing.

EOBD II Error Code: P0500
Fault Location:
Vehicle Speed Sensor (VSS) - Circuit Malfunction
Possible Cause:
Malfunction Indicator Lamp (MIL) Non Emission Fault - No warning light.
Wiring.
Vehicle speed sensor (VSS).
Engine control module (ECM).

Dec 13, 2012 | 2001 Toyota Yaris

2 Answers

P1345


With your code reader, clear the codes and check they stay gone.

Aug 15, 2017 | Cars & Trucks

2 Answers

CHECK ENGINE LIGHT ON CODE P0340


code P0340 which stands for camshaft position sensor fault.
what engine is this? if it is a 4 cylinder this can be caused by a loose timing belt.

Jul 09, 2010 | 1996 Toyota Camry

2 Answers

Engine misfire or flat spot when accelorating put occasionally


the camshaft position sensor is right around the crankshaft. there is a magnetic wheel at the end of the camshaft that the sensor uses to produce the signal.

Jun 10, 2009 | 2005 Ford Focus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

160 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8732 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...