Question about 1991 Isuzu Rodeo

1 Answer

Trying figure out how in the world to bleed my clutch on a 1991 Rodeo. I replaced the slave cylinder, tried bleeding it at the slave cylinder and the intermediate bleeder valve on the side wall of the engine compartment, by opening the slave cylinder bleed valve, depressing clutch pedal, closing bleeder valve, pulling the clutch pedal back up. After doing this 400-500 times, no progress. I bought a vacuum/bleed system and hooked it up to the slave cylinder bleed valve and while system was fully closed, pumed up the vacuum, then opened the blleder slowly. After several times doing this, no results but a tired hand. Anybody have suggestions please? This has baffled me as to how hard this is. Thanks!

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Isuzu Master
  • 20,706 Answers

Let the simpleton yada fix you
FO , mr, yahada bsa.
full of mierda , to the eye balls

Posted on Mar 30, 2017

  • yadayada
    yadayada Mar 30, 2017

    You are a jerk!

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

snownbird33
  • 120 Answers

SOURCE: 91 Ranger 2.3 5 speed

How does your clutch feel? You might just have to just adjust the clutch peddle.

Cheers

Posted on Aug 21, 2008

jocko777
  • 7 Answers

SOURCE: Low / Soft Clutch Pedal, 1995 Rodeo 2W 2.6L

at a minimum the pressure plate but not changing everything while in there would be silly

Posted on Aug 01, 2008

Thunder55
  • 318 Answers

SOURCE: clutch pedal remains on the floorboard even after two hours of

Make sure the Reservoir is filled up with brake fluid,,then manualy force the actuating rod at the slave cylinder back and forth in and out of the slave cylinder,,this should recharge the clutch system. then try bleeding again but make sure you do not allow air into the system.

Posted on Jan 29, 2009

jmassengill
  • 345 Answers

SOURCE: 1992 ISUZU RODEO CLUTCH PROBLEM

could also be the host/tube connecting the master and slave together. Could be a small hole that sucks in air when you let off the clutch and pushing the fluid out on to a host that is so dirty or in such a dark place that you can't see the fluid seeping out on the hose

Good Luck

Posted on Nov 10, 2008

autodr
  • 260 Answers

SOURCE: Bleeding clutch slave cylinder

i think youre doing the right thing. they are very stubborn to bleed because the hyd. line goes up high across back of engine before droppiing back down to slave cyl., trapping air. could try to gravity bleed by opening bleeder at slave, cap off of master cyl, full with fluid then it may start to come out after a bit. then try your process again. or can try to bleed at connections further up the line, working your way back to bleeder. hope this helps. be patient.

Posted on Nov 15, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Trying to find leak in clutch system os 1993 rodeo need diagram


Did you bench bleed the master or slave cylinder ? Is Your Brake pedal Hard ? Could be your Brake booster . send image for more understanding of your problem

Feb 25, 2014 | 1993 Isuzu Rodeo

1 Answer

How do you know if it is your clutch, clutch linkage, or clutch slave cylinder is the cause of vehicle non performance?


confirm if you have fluid leak from master or slave cylinder of if you have damp valve.try to bleed as it is to confirm the fault. If fault does not resolved then check as some times the cause is the damp valve does not allow fluid to flow through to slave cylinder. If your clutch master cylinder is ok, and the slave cylinder as well,start the bleeding by the damp valve which is on the mid way of master and salave cylinders.Then beed the slave cylinder for good clutch.

Sep 07, 2012 | 1996 Isuzu Rodeo

1 Answer

Changed clutch but unable to bleed the slave cylinder. Does that mean clutch master cylinder is bad? Got one from parts store but can't figure out how to take the clutch safty switch off to change it. Any...


Probably not. Bleeding clutch slave cylinders is tricky because you cant "pump it up". The master cylinder has no static valve so the best way to bleed the slave cyl. is to use gravity. Fill the master cylinder reservoir and open the bleed valve on the slave cyl. Allow fluid to drip into an open can until there's no trace of air. Close bleed valve and try clutch. If still no pedal, repeat the process. This is quite an acceptable procedure.

Mar 22, 2010 | 1991 Chevrolet S-10

1 Answer

I replaced the slave cylinder on my rodeo and it worked fine for a day.But know its like its like the clutch has no compression and there is a puddle on the ground below the master cylinder but the...


U need to find out were the leek is coming from exactly,then fix it.Even if it means takeing the slave cylinder off again or replaceing in again.new parts can be bad.

Mar 08, 2010 | 1991 Isuzu Rodeo

5 Answers

Stuck clutch pedal on a Mazda B series truck


Replace both clutch slave and master cylinders, and bleed well. I've also had this happen.

Jul 11, 2009 | 1988 Mazda B2200

1 Answer

How do you bleed the clutch in a 1991 Jeep Wrangler?


If replacing just the fluid, you should gravity bleed it by opening the valve at the side of the transmission where the line goes in to connect with the slave cylinder. Be sure to stand by and keep the tiny reservoir from going empty during bleeding, or you just make things worse. Assume you replaced parts. Is this right or wrong?

Or are you just trying to restore performance in a poorly operating system? Would help TONS to know these details, and how much you know about bleeding, etc. If you are trying to bleed a new slave cylinder, it can take 600 to 1800 pumps of the clutch pedal sometimes to clear it out manually. If you want instructions on how to bleed in with vacuum assistance, please post request comment to that effect.

Talk to you soon. TT

Feb 06, 2009 | 1991 Jeep Wrangler

1 Answer

1991 isuzu rodeo wont go into gear


I had the same problem and my fluid was fine! First try to bleed it (i went the easy way and bought a speed bleeder) if that doesn't do it i replaced my slave cylinder and it worked.

Feb 01, 2009 | 1991 Isuzu Rodeo

1 Answer

Clutch pedal remains on the floorboard even after two hours of


Make sure the Reservoir is filled up with brake fluid,,then manualy force the actuating rod at the slave cylinder back and forth in and out of the slave cylinder,,this should recharge the clutch system. then try bleeding again but make sure you do not allow air into the system.

Jan 01, 2009 | 2003 Isuzu Rodeo

2 Answers

Bleeding clutch slave cylinder


i think youre doing the right thing. they are very stubborn to bleed because the hyd. line goes up high across back of engine before droppiing back down to slave cyl., trapping air. could try to gravity bleed by opening bleeder at slave, cap off of master cyl, full with fluid then it may start to come out after a bit. then try your process again. or can try to bleed at connections further up the line, working your way back to bleeder. hope this helps. be patient.

Nov 15, 2008 | 1996 Honda Accord

Not finding what you are looking for?
1991 Isuzu Rodeo Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...