Question about 1990 Ford LTD Crown Victoria

Open Question

How do i put a gear shift cable on my 90 ford crown victoria an how do i hook up all the vaccum lines at the back

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 4369 Answers

SOURCE: 1998 ford crown victoria fuse box diagram

it should be in your owner manual. if not, I can look up something for you but can't post illustrations to this site.

Posted on Jan 09, 2009

  • 2920 Answers

SOURCE: ford transmission not shifting

i think you got a bad transmission...thats what it sounds like anyway

Posted on Jan 12, 2009

CLEONTI
  • 33 Answers

SOURCE: need wiring diagram for 2008 ford crown victoria

Hello,

You can purchase the wiring diagram for $5.99 from the following site: http://www.wiring-diagram.com/. You can also purchase a wiring diagram book from the following link: http://cgi.ebay.com/ebaymotors/2008-FORD-CROWN-VICTORIA-MARQUIS-WIRING-DIAGRAM-MANUAL_W0QQitemZ120394723100QQcmdZViewItemQQimsxZ20090320?IMSfp=TL090320147007r15080.

Hope this helps,

Chris

Posted on Mar 23, 2009

jaysonemanme
  • 500 Answers

SOURCE: 1995 crown vic gear problems/gear shift wont lock

most likely the shift tube bushings are bad- you may have also lost a few screws in the shift tube or they could just be loose. you have to pull the steernig column down to inspect/repair it.

Posted on May 31, 2009

  • 102 Answers

SOURCE: how to trouble shoot starting system 98 ford crown victoria

Also check to see if there is power in the start wire form the ignition switch, the wire is a white wire with pink stripe, most likely not a common problem, but still something that could go wrong. this wire will feed the starter relay under the hood...

Posted on Sep 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have 1992 ford crown victoria that doesn't shift into reverse most especially when it's warm. i've had fluid changed. fluid is reddish now. is there an adjustment? sometimes seems like i can mess with...


Fluid color don't matter. Your cable or shifting linkage may have slipped or is slipping. #1 Hold brake pedal down and move shift lever very slow around the reverse indicator. When reverse activates note were indicator is located. #2 Test the other gear indicators at the proper speeds(MPH). No problems with #2-linkage problem. Problem with both-go get a six pack. Good Luck.

Aug 04, 2013 | 1992 Ford Crown Victoria

2 Answers

How to get windows to go up and down in 1995 ford crown victoria


No up
No down
One window
All windows
Window fails down
You hear motor run & no window movement
You work the switches & they work sometimes

I would imagine you need that answered at a
repair shop

Feb 14, 2013 | 1995 Ford Crown Victoria

1 Answer

Crown victoria 1989 kick down assembly


There a tab at the linkage you unlock it and slid the cable till it is just a little loose the snap the tab back in, drive the car and make a note when the car shifts into overdrive, it should do it at about 55 miles per hour at half throttle, if it shifts to fast tighten the cable if it stays out of overdrive loosen it

Aug 22, 2012 | Ford Cars & Trucks

1 Answer

Why my 2007 crown Vic won't shift in gear


this can be due to out of adjutment of shifter cable which releases the shifter when brake is pressed.

Nov 18, 2011 | 2007 Ford Crown Victoria LX Sedan

1 Answer

How can a kickdown cable be hooked up wrong if its connected to the tranny and the throttle body on a 1992 crown victoria


More likely it is not adjusted properly Kickdown cables are used to control fluid flow in the transmission so they shift correctly If adjusted to tight or to loose it will cause the transmission to not change gears properly or not at all

Nov 10, 2009 | 1992 Ford Crown Victoria

1 Answer

1995 crown vic gear problems/gear shift wont lock


most likely the shift tube bushings are bad- you may have also lost a few screws in the shift tube or they could just be loose. you have to pull the steernig column down to inspect/repair it.

May 30, 2009 | 1995 Ford Crown Victoria

1 Answer

1995 crown vic gear problems/gear shift wont lock


if the shifter is loose and sloppy feeling then the shift cable bracket has come loose under the dash at the steering wheel. remove the lower panel under the steering wheel so you can see under the dash then get flash light and look while jiggling the shifter. you should be able to see the cable and bracket. if the bracket is loose then tighten the bolts. note this bracket is at the steering colum.

Jan 21, 2009 | 1995 Ford Crown Victoria

Not finding what you are looking for?
1990 Ford LTD Crown Victoria Logo

Related Topics:

122 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5467 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...