Question about 1998 Dodge Ram 1500 4WD

Open Question

I have a code alarm csm 2.5 remote start only. when used it engages the starter too long now the lights just flash without engaging the starter at all. how do I reset it

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: 1994 caravan 3.3 wont start

No and No

Posted on Sep 02, 2008

Ad
  • 23 Answers

SOURCE: Car won't start. Believe kill switch is engaged.

Do you have a chipped key {small black thing in the middle of the key} if not you need to take your registration into the dealer and order a new key.

Posted on Apr 03, 2009

  • 3600 Answers

SOURCE: I have a 2003 Dodge Caravan with a 3.3L it wont

Yes they do but I would rather think you have a bad battery cabe connection to the system, sometimes the battery cable corrudes and you can't see it try replacing the cable ends and the connector ends espically if they are by the battery.

Posted on Jun 18, 2009

  • 574 Answers

SOURCE: security light blinks on dash , truck wont even try to start

Does your key have a chip on it? If it does its probably the problem

Posted on Aug 23, 2009

MECP Guy
  • 344 Answers

SOURCE: tried to start my 2003 dodge ram 1500 will click

sounds like your trucks computer was not flashed with updates I would take it to the dealership and have them check to see if the software on the computer is up to date

Posted on Jan 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Security light stays on (constant) while truck is in use, no obvious problems though. What is going on


when you lock your vehicle with the remote it engages the alarm and the red light will flash fast for about 15 seconds. Then it will start flashing very slowly to show the system is armed. To disarm it you need to open the door with the remote or put the fob in the ignition. If you use the key to open the door and alarm is on it will go off. Only way I know of to make it quit honking and flashing lights is to hit unlock button or insert for into ignition.
I would sit in the vehicle and arm the lock with the remote and watch to light for about 1 minute to see if it does flash fast first then slowly. If it does it is working fine. If it doesn't then take it in and have dealer look at it.

Dec 07, 2015 | 2010 Dodge Ram Pickup 1500

1 Answer

I have a 2004 Nissan Merano and sometimes when I turn my alarm off and go to start it, it will not start and the red car with the key on it flashes please help!!!


Well, ill assume that since you have an l.e.d. your alarm is aftermarket. My guess is your alarm is in "passive arming mode". That means its arming. Itself. Some alarm dont fully arm in that mode, usually just the starter kill and led engages. That mode (sometimes happens) and can be changed via your remote. Hope that helps.

Mar 01, 2015 | 2004 Nissan Murano

1 Answer

Engine light on and remote start doesn't work.


You'll need to have the computer checked for trouble codes to proceed.

Jan 05, 2014 | 2008 Buick Lucerne

1 Answer

Remote starter won't start engine, now check engine light is on


Need more information. Does the car start normally with a key? Is there a switch for a mechanic to disable the remote start while working on it (some units have a toggle switch)

Apr 06, 2013 | 2008 Chevrolet Silverado 1500 2WD

1 Answer

Idisconected my battery for water pump have after market radio didnt think it would be a prob. but it turns over and will not start it has built in alarm and indicator light flashes rapid is there a way...


Insert ignition key,turn forwards to run. Just till red lights & theft/alarm light goes on. Do not try to start or engage starter.Leave on till light stops flashing. It may take up to 10 minutes. Once light stops flashing turn key off. Then start car & let run for awhile.

Mar 21, 2011 | Pontiac Grand Prix Cars & Trucks

1 Answer

Will not start. Battery good all lights come on starter will not engage no clicking at all


if you have aftermarket alarm/keyless entry/remote start try hitting the unlock button on the remote twice when trying to start may need to replace starter

Feb 19, 2011 | 2001 Chevrolet Blazer

1 Answer

1999 dodge durango wont start


may work may not...on older cars when the starter went bad and the car wouldn't start you could tap the starter with a long screwdriver or hammer lightly and the solenoid would engage and start the car but you need to get it home or to shop cause it wouldn't work again..if you try this and the starter engages then the starter needs to be replaced if you haven't already tried..if the lights are flashing when you try to start the vehicle then o would say its prob a malfunctioning alarm system..try to diengage it by pulling fuse for alarm..don't know if you can though..check the starter...good luck

Apr 12, 2010 | 1999 Dodge Durango

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

117 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6910 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...