Question about 1996 Geo Metro

Open Question

Looking for a 1996 Geo Metro 1.3 liter LSI Vacuum Diagram.

Posted by on


3 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 17970 Answers

SOURCE: Need firing order diagram for 1997 Geo Metro Lsi

1997 Geo Metro 1.3 liter L4 VIN "9"


Hope helps. (remember rated and comment this).

Posted on Sep 10, 2010

  • 80 Answers

SOURCE: looking for diagram of 1996

hope this helps


Posted on Jun 06, 2011

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Looking for belt diagram of 1996 geo metro

Refer to the site here:

Apr 09, 2014 | 1996 Geo Metro

1 Answer

Need firing order diagram for 1997 Geo Metro Lsi 1.3 liter 4 cilinder

1997 Geo Metro 1.3 liter L4 VIN "9"


Hope helps. (remember rated and comment this).

Sep 07, 2010 | 1997 Geo Metro

2 Answers


Engine size 1.0 or 1.3 liter??

Apr 24, 2010 | 1997 Geo Metro

1 Answer

Do the valves need to be adjusted on a 92 geo metro lsi

No. Geo Metros use hydraulic lifters which can not be adjusted. If you Metro is making excessive valve noise, the lifters are probably worn out or the oil level is low.   

Feb 27, 2010 | 1992 Geo Metro

1 Answer

Is it normal for a 96 geo lsi when its at 60 for the rpm to be at 3.5?

It's perfectly normal, the engine you got in that car is very small and it means you have less gear ratios, once on the top gear the car will speed up by staying on that gear and rev'ing up the engine.

Feb 09, 2010 | 1996 Geo Metro

1 Answer

HI i have a 2002 geo metro LSI and it is running like it has a bad miss but it also runs fine when you get the RPM.s up, It stutters climing up hills to. Do you know what it might be

Put a vacume gauge on it, bet the miss is still there.
Are you getting a check engine light?
Possible bad cylinder or a head gasket.
Any water in the oil??

Jan 24, 2010 | 1996 Geo Metro

1 Answer

I dont have a repair manual,need degrees BTDC Please

The timing on your car should be at 6° BTDC. The thing is, Do you have a vacuum advance or electronic advance? With vacuum you would unplug the hose to the distributor and plug it.(LSI) If it has two hoses to the advance it would be the outside hose. I assume you are using an inductive timing light with an inductive clamp that attaches to #1 plug wire.
With electronic ignition you must unplug the diagnostic connector located next to the ignition coil. Then use a jumper wire between the bottom to terminals on the plug. Top being with the plug latch facing up. See what you find. Good luck.

Apr 01, 2009 | 1989 Geo Metro

1 Answer

Where to fill gear oil in manual 5 speed 1990 geo lsi

It should be the same place as a 1991 Metro, on the back side of the transaxle there is a plug that takes a 15/16 wrench to remove. the plug faces the drivers side tire. If oil drips out when you remove the plug it is full. Otherwise use your finger to see if you can touch the oil. Fill with some type of syringe. jeb

Dec 29, 2008 | 1991 Geo Metro

Not finding what you are looking for?
1996 Geo Metro Logo

Related Topics:

308 people viewed this question

Ask a Question

Usually answered in minutes!

Top Geo Experts


Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Geo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides