Question about 1996 Land Rover Range Rover

1 Answer

Is it possible to change the ignition coils with the engine in situ ?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 100 Answers

Yes, on a 1996 Range Rover there is just a couple of bolts and the coil pack assy comes right off.
The cylinders are numbered on the coil pack. The 1996 has 1 coil pack for all the cylinders.
1999 -2002 has 2 coil packs which can also be replaced with everything still assembled but it is much more difficult and it can take a qualified technician upto 2 hours to replace them

Posted on Oct 12, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Error Code P0351 for a 2005 Toyota Avalon


Possible causes
Faulty Ignition Coil 1
Ignition Coil 1 harness is open or shorted
Ignition Coil 1 circuit poor electrical connection
Faulty Engine Control Module (ECM)

What does this mean? When is the code detected? Each ignition circuit is continuously monitored by the Engine Control Module (ECM). The test fails when the ECM does not receive a valid pulse signal from the ignition coil. Possible symptoms Engine Light ON (or Service Engine Soon Warning Light) Lack/Loss of Power Engine may be harder to start Engine hesitation Rough engine idle P0351 TOYOTA Description: The ignition system on the vehicle uses individual ignition coils for each cylinder. The Engine Control Module (ECM) controls each ignition coil operation. The ECM sends a ON/OFF signal to energize the ignition coil to create a spark at the spark plug when a spark is required at the cylinder.

May 29, 2017 | Toyota Cars & Trucks

1 Answer

P0351 code loss of power 2.3L08ford ranger,it warms slow and really need to eliminate1~voltage regulator is where?) & 2~ ground through PCM) 3~knowing limits&threashholds{sensorsIGNcircuit}?Ty 0$


P0351 loss of power ? That's not what this code is about . P0351 - Ignition Coil A Primary/Secondary Circuit ,you have a bad coil and possibly a bad coil driver inside the PCM . Do yourself a favor an take your vehicle to a qualified repair shop !
P0351 - Ignition Coil A Primary/Secondary Circuit Description: See the description for DTC P0350. Possible Causes: See the possible causes for DTC P0350. Diagnostic Aids: See the diagnostic aids for DTC P0350. Application Key On Engine Off Key On Engine Running Continuous Memory Coil-on-plug (COP) ignition testing - GO to Pinpoint Test JF . GO to Pinpoint Test JF . Coil pack ignition testing - GO to Pinpoint Test JE . GO to Pinpoint Test JE .
P0350 - Ignition Coil Primary/Secondary Circuit Description: Each ignition primary circuit is continuously monitored. The test fails when the powertrain control module (PCM) does not receive a valid ignition diagnostic monitor (IDM) pulse signal from the ignition module (integrated in the PCM). Possible Causes:
  • Open or short in the ignition START/RUN circuit
  • Open coil driver circuit
  • Coil driver circuit short to ground
  • Damaged coil
  • Coil driver circuit short to VPWR
Diagnostic Aids: Use the 12-volt non-powered test lamp to verify START/RUN voltage at the ignition coil harness connector.
Check the coil driver circuit for open, short to VPWR, or short to ground. Application Key On Engine Off Key On Engine Running Continuous Memory All GO to Pinpoint Test JE .

Feb 18, 2017 | 2008 Ford Ranger

1 Answer

I have a p2323 code and replaced the spark plugs. I pulled the battery cable and after a week the code came back. What could be causing this.


P2323 Dodge - Ignition Coil Secondary Number 8 Circuit Condition - Faulty spark plug or coil boot
- Faulty Ignition Coil 8
- Ignition Coil 8 harness is open or shorted
- Ignition Coil 8 circuit poor electrical connection
Possible symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Engine may be running rough

P2323 Dodge Description
The ignition system is controlled by the Powertrain Control Module (PCM) on all engines. Each cylinder is equipped with 1 dual-output coil. Meaning one coil mounts directly over one of the dual spark plugs for 1 high-voltage output.
Battery voltage is supplied to all of the ignition coils positive terminals from the ASD relay. If the PCM does not see a signal from the crankshaft and camshaft sensors (indicating the ignition key is ON but the engine is not running), it will shut down the ASD circuit.
Base ignition timing is not adjustable. By controlling the coil ground circuits, the PCM is able to set the base timing and adjust the ignition timing advance. This is done to meet changing engine operating conditions.
The PCM adjusts ignition timing based on inputs it receives from:
- The engine coolant temperature sensor
- The crankshaft position sensor (engine speed)
- The camshaft position sensor (crankshaft position)
- The manifold absolute pressure (MAP) sensor
- The throttle position sensor
- Transmission gear selection
Read more: http://engine-codes.com/p2323_dodge.html#ixzz3UfaKMLrR

I hope this helps!

Ted

Mar 17, 2015 | 2011 Dodge Ram Pickup 1500

1 Answer

Po 353 code


P0353 CHEVROLET Description The ignition system on the vehicle uses individual ignition coils for each cylinder. The Powertrain Control Module (PCM) controls each ignition coil operation. The PCM sends a ON/OFF signal to energize the ignition coil to create a spark at the spark plug when a spark is required at the cylinder.

Possible Causes - Ignition Coil harness is open or shorted
- Ignition Coil circuit poor electrical connection
- Faulty Ignition Coil 3
- Faulty Powertrain Control Module (PCM)
Read more: http://engine-codes.com/p0353_chevrolet.html#ixzz21kWvhhBc

Jul 26, 2012 | 2006 Chevrolet Cobalt

1 Answer

1990chevy suburban 2500 350 died while driving and won't restart I can hear the fuel pump turn on I have changed the fuel filter and still nothing what's next


check for spark, no spark, no fire engine wont run, possible bad ignition coil, wire from coil to distributor cap, no power to ignition coil from ignition switch (rare) wire broken to ignition coil (even rarer)

Jul 09, 2012 | Cars & Trucks

2 Answers

I have a 02 dodge grand caravan sport with 0351,0352,0700 codes...car runs good then shakes and even stalls at times,but not all the time...i have replaced ignition coil,wires,plugs,and catalytic...


po700 code just means you have codes
P0351-IGNITION COIL #1 PRIMARY CIRCUIT

WHEN MONITORED
With battery voltage greater than 8 volts during engine cranking or greater than 13 volts with engine running. Engine RPM less than 3000. No coil in dwell during test.

SET CONDITION
Peak current is not achieved with battery based dwell plus 1.5 msec of diagnostic offset. It takes less than 3 seconds during cranking or up to 6 seconds while running to set.

POSSIBLE CAUSES
- Ignition coil
- Intermittent condition
- ASD relay output circuit
- Ignition coil driver circuit open
- Ignition coil driver circuit shorted to ground
- PCM

P0352-IGNITION COIL #2 PRIMARY CIRCUIT

TEST NOTE
This symptom is diagnosed using the test P0351-IGNITION COIL #1 PRIMARY CIRCUIT.

WHEN MONITORED
With battery voltage greater than 8 volts during engine cranking or greater than 13 volts with engine running. Engine RPM less than 3000. No coil in dwell during test.

SET CONDITION
Peak current is not achieved with battery based dwell plus 1.5 msec of diagnostic offset. It takes less than 3 seconds during cranking or up to 6 seconds while running to set.

POSSIBLE CAUSES
- Ignition coil
- Intermittent condition
- ASD relay output circuit
- Ignition coil driver circuit open
- Ignition coil driver circuit shorted to ground
- PCM
var classElements = new Array(); var node = document; var tag = 'a'; var els = node.getElementsByTagName(tag); var elsLen = els.length; var pattern = new RegExp("(^'\\s)specs_note(\\s'$)"); for (i = 0, j = 0; i
var classElements = new Array(); var node = document; var tag = 'a'; var els = node.getElementsByTagName(tag); var elsLen = els.length; var pattern = new RegExp("(^'\\s)specs_note(\\s'$)"); for (i = 0, j = 0; i

Jun 14, 2011 | 2002 Dodge Grand Caravan

1 Answer

I have no spark in cylinders 2,4,6 on my 2002 Ford escape and three codes 354,355,356 Which means the same . After checkin those Three coils I found out , there is no negative Any advise?


P0354 - Ignition Coil D Primary/Secondary Circuit Malfunction.

Description of DTC:
The ignition signal from the Powertrain Control Module (PCM) or Electronic Control Module(ECM) is sent to and amplified by the power transistor. The power transistor turns ON and OFF the ignition coil primary circuit. This ON/OFF operation induces the proper high voltage in the coil secondary circuit.

Symptoms:
- Lack/Loss of Power
- The engine may be harder to start
- Engine hesitation
- Check Engine Light On
- No spark

Possible Causes:
- Open or short in the ignition coil circuit
- Ignition coil circuit shorted to ground
- Ignition coil connector
- Damaged ignition coil
- Damaged PCM or ECM

Possible Solutions:
- If damage, repair ignition coil circuit
- Replace ignition coil
- Replace PCM or ECM



P0355 - Ignition Coil E Primary/Secondary Circuit Malfunction.

P0356 - Ignition Coil F Primary/Secondary Circuit Malfunction.

Jan 18, 2011 | 2002 Ford Escape

1 Answer

P0352 code came up what might be the problem


P0352 - Ignition Coil B Primary/Secondary Circuit Malfunction
The ignition signal from the Powertrain Control Module (PCM) or Electronic Control Module(ECM) is sent to and amplified by the power transistor. The power transistor turns ON and OFF the ignition coil primary circuit. This ON/OFF operation induces the proper high voltage in the coil secondary circuit.

When is the code detected?
The test fails when the Powertrain Control Module (PCM) or Electronic Control Module(ECM) does not receive a valid pulse signal from the ignition coil.

Symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Lack/Loss of Power
- The engine may be harder to start
- Engine hesitation

Possible causes
- Open or short in the ignition coil circuit
- Ignition coil circuit shorted to ground
- Ignition coil connector
- Damaged ignition coil
- Damaged PCM or

Possible solution
- If damage, repair ignition coil circuit
- Replaced ignition coil
- Replaced PCM or ECM


Hope helps with this (remember to rate this answer).

Jan 14, 2011 | Mazda RX-8 Cars & Trucks

1 Answer

1988 Ford Galaxy auxillary drive belt tensioner 2.3


yes it can be removed ,i changed a timing belt with everything in situ

Dec 15, 2008 | 1978 Ford Granada

Not finding what you are looking for?
1996 Land Rover Range Rover Logo

247 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...