Question about 1994 Jeep Grand Cherokee

1 Answer

How can I remove the safety switch, from the tranny? It sits right against the top of the fluid pan and can not get a socket into it.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 6,982 Answers

Don't understand why a socket won't go in there but you can try using a "crows foot" (looks like the end of an open end wrench with a provision for an extension to turn it)

Posted on Oct 12, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to put in a tranny filter on a 91 gmc 4x4 4.3l blazer


You remove the transmission pan and then remove the old filter. Make sure you remove the old seal out of the valve body and install new filter with new seal and re-install pan. Fill with fluid and you are done.

Nov 15, 2014 | Cars & Trucks

2 Answers

How to drain and fill transmission fluid in 2012 chevy malibu?


GET NEW GASKET AND FILTER FOR TRANNY ALONG WITH THE FLUID (BEFORE YOU BEGINE)
GET A LARGE FLAT DRAIN PAN.
PUT CAR UP ON 4 JACK STANDS.
place drain pan under tranny pan.
undo tranny pan screws - allow one corner to hang lower than the other corner (to allow fluid to drain) slowly remove them all.
Its messy! empty tranny pan into drain pan. set tranny pan to the side. undo the filter clamp, carefully remove the filter - set into the drain pan, remove the gasket around the tranny body/tranny pan.
Clean tranny block surface with clean cloth. install new filter, install clamp tightly. Clean tranny pan, place gasket onto pan and then reinstall tranny pan. (this only change the fluid in the tranny body and pan) If you wan the fluid out of the torque convertor you have pull the pan under the torque convertor and turn the convertor so you can get at the drain plug. Allow fluid to drain into drain pan. Reinstall drain plug and pan. (you will need a lot of fluid) Check manual for qty. Place car back on to ground/floor. Refill tranny through filler tube. Do not start the engine until oil is at full mark, and when you do start it do not all it to run for than 4 minutes - stop and add more fluid and check full mark again (repeat until no longer sinks below full mark. gently test drive around you block -- come back and check level while engine running. Top up if needed.
Siphon out excess above full mark. Test drive around 3 block,
come back check full mark. Because the torque convertor was emptied it can take a while to get all the air out it.

Jul 19, 2014 | 2012 Chevrolet Malibu

1 Answer

How do I, automatic trans filter and fluid replacement.


i would not reccomend changing transmission fluid yourself. do not do it!!!

to change transmission fluid and filter, you have to take the tranny pan off the bottom of the tranny and it will make a mess of fluid. then you have to carefully remove the old tranny pan gasket, which is best done with a special machine. if you fail to remove all of the gasaket, or damage the lip of the pan while removing the gasket, then the new tranny seal will leak, and the tranny will not hold fluid. tranny fluid and filter needs to be done in a professional shop where they have the correct equiptment.

Mar 13, 2011 | 1997 Toyota Tacoma

2 Answers

I need to replace the transmission filter on a 93 g20 sportvan. Where is is located? What tools will I need?


The transmission filter is located inside the large pan on the bottom of the transmission. There will be many small 10mm bolts to remove approx 15 of them.Just loosen them because when the seal is broke on the pan gasket the fluid will start to come out that is how it is drained. Once removed you will see it sitting there. Remove it install the new one with the o ring and replace the pan gasket. The gasket usually always comes with the filter. Re-install pan and tighten bolts in a criss cross pattern equally

Jan 19, 2011 | Chevrolet G20 Cars & Trucks

3 Answers

How to change trans. fluid and filter in a 2000 mitsu. mirage 1.8?


first you need to get a pair of safety glasses to protect eyes from cleaner. then you need 12.6 pts or 6.5 to 7 quarts of transmission fluid+ filter.you also need a drain pan to catch transmission fluid.you need a 3/8 ratchette and socket set.you need some paper towel and maybe1 or 2 cans of brake cleaner.now you want to safely raise and support car on jack stands.make sure you are on solid level ground.put drain pan under transmission to catch fluid.take ratchette wrench start removing tranny pan front and side bolts.loosen rear bolts one turn let the pan drain.when all tranny fluid drain out of pan. then remove pan clean it good with brake cleaner.remove all traces of old gasket. from pan then dry with paper towel..then you remove tranny filter.becareful not to damage anythingthen put in your new tranny filter then.wipe and carefully clean around gasket area on transmission with paper towel.make sure there is no traces of olds gasket material on tranny area where tranny pan gasket seals.now get new gasket align its with tranny pan holes.you might want to buy a gasket adhesive.just put on some to hold gasket in place when you install it to transmission.besure to clean all tranny pan bolts real good with brake cleaner. then dry them off real good.because some transmission you have to put a little rtv sealant on bolts.to keep them from leaking.now once you get bolt holesand gasket on transmission pan line up.all tranny pans bolts with a little rtv silicone on threads and on bolts head where they meet the pan.then you transmission pan in place.make sure gasket and bolt holes line up.when putting bolts in dont tighten them until you get them all in first.when all bolts are in.then you tighten criss cross dont over tighten them. torque them to 90 inch pounds .when all is done .starting putting tranny fluid in.and check for leaks.start the engine up let it idle for few minutes if you see no leaks lower car down to ground.then move transmission gear selector through each range and back to park.make sure tranny fluid level correct before driving car. WARNING IF YOUR CAR DONT HAVE THE TRANSMISSION DIP STICK.AND HAVE A FILL CAP INSTEAD THE DEALERSHIP HAS TO CHANGE FLUID.BECAUSE THEY HAVE TO RAISE CAR ON LIFT TO CHECK FLUID LEVEL.BECAUSE CAR HAS TO BE RAISE UP LEVEL THEN A DRIP PLUG IS MOVED TO CHECK TRANNY FLUID LEVEL.

Jul 19, 2009 | 2000 Mitsubishi Mirage

1 Answer

How to change transmission fluid and filter in a 2001 kia sportage, my car sounds as if it is not switching gears, the other day i was sitting in park and the rpms jumped up to like 2 and then it was quiet...


the is a drain plug on bottom of tranny. Remove all tranny fluid. Then remove bolts on the tranny pan, remove pan. Remove couple filter bolts and change filter. Replace new gasket and tranny pan. Fill up tranny with 8 quarts or whatever your user manual says with correct fluid.

Jul 09, 2009 | 2001 Kia Sportage

1 Answer

00' Kia Sephia LS not shifting past 1st gear


first you need to buy transmission fluid new filter and new gasket.you need 11.4 pints of transmision fluid.raise front of vechicle.set parking brake.block both back wheels.besure support vechicle weight with jack stands. get a drain pan.if your transmission pan dont have a drain plug.loosen rear pan bolts a few turns.remove the front and side transmission pan bolts. let fluid drain.remove tranny pan. then clean old gasket material from transmission and pan carefully.dont scratch or damage surface.clean old tranny bolts using brake cleaner or buy new tranny bolts.you have to put a tiny film of rtv silicone on tranny bolts so they wont leak.carefully remove old tranny filter and put on new filter.clean all grease grim away from tranny pan it should be **** and span because.you might need a little gasket adhesive to hold gasket in place while putting pan back on transmission.to line up bolt holes.loosely put all bolts in you have to move pan a little to get holes line up.when all is finish put tranny fluid back in.besure you put 11.4 pints back in that about 6.5 quarts. make sure tranny fluid level is right before driving vechicle.l

Jun 19, 2009 | 2000 Kia Sephia

1 Answer

Tranny pan gasket replacement problems


The (top hat) is a filter seal. If you did not change that seal then you may have damaged the old seal(still in the trans). You can remove the pan and take the filter back down. Look at the seal close, I would replace it. You can bend the old one, carefully with a screwdriver and get it out of the trans case. Tap the new one in with a socket. If your fluid is black,or there is metal in the pan then you have damage and the trans will have to be rebuilt.

Apr 30, 2009 | 1998 Chevrolet Cavalier

1 Answer

Transmission service


Because you say that it looks like a sealed unit, I am guessing that you have a manual tranny. I have never bothered to replace the fluid in any manual transmission I have ever had, but I have never had 200,000 miles on one either. Anyway, to get the old fluid out, remove the plug near the bottom of the tranny. It has a head that has an internal square recess. Use a socket wrench (with no socket) to get it out. To replace the fluid - find this plug and remove it before you begin - you have to squirt it into a fill hole about halfway up the transmission. When oil starts to come back out of the hole, then you know it is full. You will have to check with your auto parts store to find out what kind it takes and how much. A manual transmission has no filter.
If your tranny is an automatic, I would recommend having it flushed, because even if you remove the pan, there is still a couple of quarts still in the tranny. When they flush them, they get all of the fluid changed.

Sep 18, 2008 | 1996 Honda Accord

2 Answers

Flushing the transmission


To change the transmission fluid make sure you have purchased: 1. filter with the o-ring 2. MOPAR ATF + 3 Type 7176, p/n 05010124AA fluid (I believe it took 6 quarts?) You are not changing the torque converter fluid so there will not be 12 quarts needed.). 3. Pan gasket. You should receive the new neoprene reusable pan gasket. This is because the recommendation is to change the transmission fluid every 25,000 miles. 4. There is a fluid additive to prevent foaming? Use it.


Raise the vehicle on a hoist. Remove the pan bolts. Remove the old gasket material with a plastic scraper. There could be metal transfer if you use a metal scraper. Clean the pan carefully. Clean the magnet that sits in the pan as it collects the minute metal shavings. If you see an excess of larger particles, you really should have the transmission inspected at a shop. Replace the filter carefully looking at its arrangement before removing. It took a second look to install a new filter because I did not watch how it was situated before removing. Use a thin coat of transmission fluid on the new pan gasket. Orient reusable gasket properly with bolt holes and assemble oil pan and gasket to transmission case. Tighten oil pan bolts to 19 Nm (165 in lbs.). CAUTION: DO NOT OVERFILL TRANSAXLE. DO NOT ADD OIL IF LEVEL IS BETWEEN: LOWER HOLES FOR WARM OIL (100?F). UPPER HOLES FOR HOT OIL (180?F.).

Jun 12, 2008 | Chrysler Neon Cars & Trucks

Not finding what you are looking for?
1994 Jeep Grand Cherokee Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...