Question about 1991 Toyota Land Cruiser

Open Question

Change toyota 80 series rear wheel bearing and seal

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 4 Answers

SOURCE: noisy rear bearing?

Is isnt the rear end it would be very bad shaking and wouldnt last long because it would throw a bearing out. So its most likly the wheel bearing and you can just take it to a local automotive shop.

Posted on Aug 12, 2008

Ad
  • 2920 Answers

SOURCE: Changing of front wheel bearing

i assume u want to both inner and outer bearings...you have to pull the whell off the caliper for the brakes has to come off,there will be a center cap on the hub,,take ot off,inside there you will find a nuts with a cotter pin in it.remove it.gently pull on the hub abd iit should come off in your hands.the outer bearings will come out always remember to repack them with grease before you replace them the inner bearings will be behind the rotor and will have to be chanfed also as well as greased,you have to do this on both sides the same process.put it back together the same way you take it apart

Posted on Aug 15, 2008

  • 393 Answers

SOURCE: replacing rear wheel bearings on 1999 hyundai sonata

  1. for drum brakes with sealed hub(all one piece) remove lug nuts and wheel.
  2. spray penetrating oil around studs if there is a big phillips head screw visible remove it with impact driver/if not use big ballpeen hammer ,tap on flat of drum near studs(becareful not to hit them) until drum loosens(your creating a shockwave to loosen rust)
  3. once drum is off there are 4-bolts coming in from behind backing plate, remove them then hub should be able to be removed w/a little persuation from hammer.
with out sealed hub ,
  1. remove wheel
  2. remove dust cap,cotterpin,star washer(if equipped) do not re use cotter pin
  3. remove nut then washer, wiggle brake drum and front bearing will come out.
  4. put nut on shaft tighten 2-3 turns grab drum by sides and pull towards you this should remove drum leaving inner bearing/seal on shaft
  5. to replace reverse procedure making sure to pack new bearings w/grease(take drum and use long punch to remove bearing races, use race/seal installer to install new races
with disk brakes

  1. remove wheel
  2. remove caliper/bracket
  3. remove rotor
  4. remove 4-bolts from behind,tap old hub out
  5. reverse procedure



Posted on Nov 15, 2008

Puterwiz82
  • 60 Answers

SOURCE: 2002 Kia Rio rear wheel bearing passenger side

I'm from the United States, East coast.

Posted on Nov 24, 2008

  • 2 Answers

SOURCE: what torque for rear wheel bearing Ford Focus 2000

Can only find out that the hub needs to be tightened to
235 nm Dunno if this helps

Posted on Jan 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rear wheel bearing 2002 toyota hihlander


On front wheel drive models, the rear hub bearing is an assembly that bolts to the spindle.
Not sure about AllWheelDrive models.

Jun 29, 2012 | 2002 Toyota Highlander

1 Answer

I have a 1999 Mercury Grand Marquis. i noticed a little diff fluid coming from the right rear wheel. I changed the wheel seal and axle bearing and put it all back together and filled the rear diff with...


first swap to a front tyre to eliminate that issue


new bearing shouldn't be rumbling
to get the bearing square on and home
did you use a press to fit the bearing to the rear axle
or tube method ?

and did the seal kit have this nifty plastic seal fitter so axle didn;t rip the seal surface

index-iamfpwhpnyqdk3sl3340sktr-1-0.jpg

Apr 12, 2017 | 1999 Mercury Grand Marquis

1 Answer

Need to change rear seals in axcles how to? 98 gmc jimmy


First i would check to see if the axle air vent was clear if its not the oil is vary heavy and expands a lot this will build up pressure inside the houseing and cause the axle seals to leak if you can clear it the problem may fix it self its 80 90 weight oil thats thick stuff. If not you need to remove the rear wheels and brake drums then you have to remove the cover from the rear carriar catch the oil. Look inside the carriar houseing you will see the ends of the axles theres a small clip on each axle called a c clip remove them you can pull them out with your fingers. Then you can slide the axles out past the brake plates pry the seals out you might as well replace the bearings when your doing but thats up to you. Lube and install the bearings then the new seals you will need new seals lube the seal lips and vary carefuly slide the axle in taking care not to damage the seal install the c clip do the other side put a new gasket on the rear carriar tighten bolts to 20 ft lbs. Refill carriar 80 90 weight oil through filler plug on the side of the houseing until it just starts to run out hole put the plug in the rear drums on and wheels

Dec 30, 2010 | 1998 GMC Jimmy

1 Answer

80 SERIES 4.5L 1996 petrol GXL.... front passenger axel seal is leakin wat is invovled in changin it like to do i have to remove the clips in the diff or is there ne major parts that r invovled


wheel, wheel locker, caliper,disc, spindle locknut,bearing retainer nut, wheel bearing,hub,this brings you to the major parts that require special tools to remove, if you're going to do this, get a good shop manual, it'll give you a break down on all parts and tools required, or go to the library and have a look at there manuals, it'll let you know if you want to get involved or not, good luck

Nov 29, 2009 | 1996 Toyota Land Cruiser

1 Answer

Change the front wheel bearings toyota corolla 1992


front wheel bearings on this vehicle are part of a hub assy. you will have to completely remove the steering knuckle, press out the old bearing hub and rear seal and press in the new one.

Aug 03, 2009 | 1993 Toyota Corolla

2 Answers

Replacing 1988 toyota 4 wheel drive truck rear end wheel bearing


the rear wheel bearings are sealed units, that are pressed on the axel. you must have a press to get them off or on.

Jul 01, 2009 | 1988 Toyota Pickup

1 Answer

1991 mr2 rev 2. car sways left to right at 80 mph


Clunking? Probably one or both wheel bearings. Dude, that car is like UNSAFE to drive!! Jack the rear of the car up and yank on the wheel. If it moves the bearings are bad. Pull in and out and also pry up and down with a bar. Check for broken or bent rear suspension parts, or just plain worn out bushings.

Jun 30, 2009 | 1991 Toyota MR2

1 Answer

How to change a rear wheel bearing on a 1994 toyota camry


The rear wheel bearing on a toyota camry is replaced by replacing the wheel bearing and hub as a unit. this is a design change as compare to older models with two piece wheel bearings. Scotch drive wheels. Remove rear wheel. Remove rear brake drum. (note: if emergency brakes are applied you will not be able to remove brake drum) Remove dust cap and hub retaining nut. Hub should slide off as unit. Replace hub with new unit. Installation is reverse of removal.

May 30, 2009 | 1994 Toyota Camry

1 Answer

Need to see a diagram of how to change rear wheel bearing on my 320 touring 1996


BMW uses CV shafts for the rear drive axle, the wheel bearing there is a pressed in factory sealed bearing and not removable other than using a press to remove it, to press it you will need to remove the lower control arm.

May 22, 2009 | 1999 BMW 323 Series

1 Answer

Grease leak toyota 4runner 1996


You need to disconnect the rear wheel cylinder brake line and pull off the rear backing plate, via the 4 bolts that are visible after you remove the brake shoes. One the backing plate is loose, take it down, out of the way, and pull the axle shaft straight out. You will need several parts from a Toyota Dealer, and a machine shop to press off the old bearings and seals, and to press on the new bearings and seals. Go to the dealer & tell them your problem, we do this job once-twice a week; a common issue. The only seal that you can change yourself is the axle tube "outer" seal, you will see it when you pull out the shaft. But, this seal is not the cause of your leak. The inner seal on the shaft is worn. You will also need to replace the oily brake shoes, too. Hope this helps. A FIxYa rating would be appreciated.

Feb 26, 2009 | 1998 Toyota 4Runner

Not finding what you are looking for?
1991 Toyota Land Cruiser Logo

Related Topics:

356 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...