Question about 1996 Toyota Camry

1 Answer

Have change all light bulbs on both sides of the tail end; running bulb, parking bulb, corner,signal bulb, reverse light and all is working but the check rear lights on the dashboard comes on and stays on as soon as the engine starts and transmission is placed in gear

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 18 Answers

Pull your fuse for your courtsey and then put it back in everything in the veicle will reset then your light shouldent come on on the dash

Posted on Oct 12, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2005 Chevy Equinox passenger side tailight doesn't work. Brake light, turn signal, and hazard work but unit does not illuminate at night. Easy fix ?


Have you tried swapping the bulb from the other side see if that works If not check for power and ground at the tail lamp circuit that is inoperative. Also take a good look at the connector(s) make sure there is no corrosion in the terminals.

May 19, 2014 | Cars & Trucks

2 Answers

2006 Jeep Commander Tail light


The tail light circuit is separate from the brake and turn signal circuit. Either the bulb socket has gone bad or a wire has flaked out. Check for voltage at the socket on either pin base when you have your parking lights on. If voltage is present, it is either a worn socket failing to hold the bulb properly, or another bad bulb. If no voltage, determine which wire on the other side is tail light power, and run a new wire across to the side that isn't working and connect it to provide power.

Apr 09, 2014 | 2006 Jeep Commander

1 Answer

Turn signal hazard lights work but not running lights


The parking lights should be on a different circuit from turn signals - hazard lights. The bulbs usually have two filaments, one for each circuit.
On most models there is a tail light fuse and relay that handles front and rear parking lights.

Jun 28, 2013 | Toyota Tacoma Cars & Trucks

1 Answer

How do I change a brake light bulb in a 1999 c70 volvo?


Welcome to FixYa.com
Brake Lamp Replacement

Location of the lights

Image

The illustration shows the locations of the lights on the RH side. The LH side is the same but

mirror-reversed.

The lights have the following functions:

- 1 +1 = Parking light Fail light

- 2 = Reversing light

- 3 = Fog light LH side only (LHD cars)

- 5 = Direction indicator

- 6 = Brake light

Image

Tail light changing bulbs

Ignition off.

Open the cover in front of the tail light

Undo the wing nut and take out the lamp holder.

Change the defective bulb.

Fit in reverse order.

Check that all bulbs lamps are intact and in working order.

Image

Replacement of tail light cluster

Note! If a new tail light is to be fitted, the sleeves must be ground down 1.5 mm.

Open the cover in front of the tail light Undo the panel partly in front of the tail light Unplug the

connector for the tail light Undo the four nuts securing the tail light see illustration.

Pull the tail light straight out. Fit in reverse order

Note! check the sealing and fit on reassembly.

Check that all bulbs lamps are intact and in working order.Thank you for Using FixYa.comKind Regards, LeeYour FixYa Expert and Master Technician

Jan 27, 2011 | 1999 Volvo C70

1 Answer

Change out a taillight


You want to change the tail light bulb?

The process for replacing tail light bulbs is the same in all models. If you have a burnt-out tail light bulb, you may need to replace the brake light, the reverse light or the turn signal. The procedure to replace each of the bulbs is the same.



    Instructions

    1. Open the Hummer's rear swing gate. This will expose the edge of the vehicle's tail light assembly. You'll see two small Phillips head screws that hold the tail light assembly in place. Put on your gloves.

    2. Remove the two screws from the tail light assembly. Pull the tail light out and inspect the back for two bulbs. The top bulb is the brake light and turn signal. The bottom bulb is the reverse bulb. Determine which bulb you need to replace.

    3Rotate the bulb's socket counterclockwise to disconnect it. Unplug the bulb from its socket.

    4Push the replacement bulb into its socket firmly. Insert the socket back into the tail light. Turn it clockwise to secure it in place.

    5Place the tail light into its cradle. Hold it with one hand and replace the Phillips head screws with the other.

Dec 03, 2010 | 2008 Hummer H3

1 Answer

How do i change the tail light on a 2004 tahoe


Open rear hatch. Remove two mounting screws at the side corner which mount the tail light assy to the body. The whole tail light assy can now be removed. Twist desired bulb holder counterclock wise to remove, then pull bulb to remove. Reinstall in reverse order.

May 19, 2010 | 2004 Chevrolet Tahoe

1 Answer

How do I replace the passenger side corner light and front side turn signal light?


Front Turn Signal & Parking Lights


7ccc73e.gif
Remove the 2 parking light housing retaining screws ...


9898a80.gif
... then pull the housing away from the vehicle far enough to remove the bulb socket from behind the housing. Turn the socket counterclockwise and pull


a323ae9.gif
Push the bulb in the socket gently and turn clockwise, then pull the bulb out of the socket. Note the offset retaining ears on each side of the bulb


  1. Remove the screws from the lens and separate the lens from the headlight bezel.
  2. Remove the headlight bezel.
  3. Remove the screws from the turn signal housing and pull it out.
  4. Turn the bulb socket counterclockwise 1/3 turn and remove it.
  5. Installation is the reverse of removal.


Side Marker Lights
  1. Remove the screws from the marker lens and separate the lens from the headlight bezel.
  2. Pull the bulb from its socket in the back of the lens.
  3. Installation is the reverse of removal.

Feb 14, 2010 | 1997 Jeep Grand Cherokee

1 Answer

HOW MANY BULBS ARE IN THE REAR LIGHTS (SUCH AS FOR PARKING, REVERSE, BRAKE). IF WARNING LIGHT ON PANEL IS ONE, WOULD I SEE A BURNT OUT BULB?


You may or may not see a burnt out bulb. The dash light can also mean there's a current issue (ie none of the bulbs are lighting)

2 reverse bulbs
2 license plate bulbs
2 turn signal bulbs
2 rear sidemarker bulbs (side of your tail light assembly)
2 running light bulbs which are the same as your stop light bulbs in the tail light assembly
1 to 6 high mount stop light bulbs (if they're in the window and varies on models)
1 strip of LED brake lights if you have a spoiler



Sep 24, 2009 | 2002 Toyota Camry

Not finding what you are looking for?
1996 Toyota Camry Logo

319 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...