Question about 2002 Ford Ranger Regular Cab

2 Answers

Code ? 2002 raner 2.3L with 5-speed has a obd-II code of p1537 .What is it and where is it located

Posted by on

  • rangerbill Jun 09, 2008

    thanks for trying. It is a 2 wheel drive supercab. I think it has somthing to do with the intake manifold runner control.

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I have had the same error code. It was the vacuum line to that sensor from the intake that had a break in the line at the sensor. The sensor is located on the drivers side of the engine near the bottom. Follow from the intake next to the firewall and look down. It is easier to see from under the truck. The vacuum line comes from the intake manifold near the middle and runs down to the sensor. Also check the plug on the back of the sensor.You can also find other obd codes on google.

Posted on Jun 19, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 625 Answers

Make sure it is p1537 because i have the manual and do not show that code for this specific car
and is it 2 or 4 wheel drive

Posted on Jun 02, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 toyota highlander 3.0 code C1233. after stop sign make sound when accelerate


Toyota Highlander C1233 OBD-II Diagnostic Chassis (C) Trouble Code Description Toyota Highlander car C1233 OBD-II Trouble Code The ABS module receives wheel speed readings from each wheel speed sensor and processes this information to determine if an ABS event is necessary. The wheel speed sensor detects the magnetic field of Reason For Toyota Highlander C1233 Code The reason of Toyota Highlander C1233 OBD-II Engine Trouble Code is C1233 Left Front Wheel Speed Sensor Input Signal Missing.

Nov 03, 2015 | Toyota Cars & Trucks

1 Answer

Whats ford windstar error codes p0715 mean


I hope this helps and is what your looking for... good luck

http://www.fordobdcode.com/p0715-ford

Ford P0715 OBD-II Trouble Code Definition:
P0715 Input Shaft Speed Sensor Circuit Malfunction
P0715 Ford OBD-II Trouble CodeDescription:
OBD Trouble Code P0715 Input/Turbine Speed Sensor "A" Circuit What does the code mean? OBD-ii Code P0715 definition:
The input speed sensor detects the primary pulley revolution speed and sends a signal to the Transmission Control Module (TCM) and Engine Control Module (ECM). Symptoms Sumptoms of OBD code P0715
- Engine Light ON (or Service Engine Soon Warning Light) - Possible shifting problems Causes Causes of the OBD-II code P0715
- Transmission speed sensor circuit is open or shorted. - Poor transmission speed sensor circuit connection - Faulty transmission speed sensor The Error code is generally activated on detection of the following conditions: Diagnostic Trouble Code (DTC) P0715 is detected when TCM or ECM does not receive the proper signal from the sensor. Solutions

Jun 22, 2014 | 1999 Ford Windstar

1 Answer

I have audi Q5 2010 model i have a fault code to the transmission i dont know what is this P1f68


HI,
Strongly suggest taking to the dealer as it should still be under warranty.

Code info I googled:

OBD II Fault Code P1F68 :Description of OBD II Fault code P1F68

TH2TNK Sensor Value Offset Shifting
Possible failuer of OBD II Fault code P1F68

  • Hydrogen Tank Internal Temperature Sensor (TH2TNK) offset shifting
  • Inlet Air Temperature Sensor (TA) offset shifting
  • Offset shifting of both Teperature Sensor (TH2TNK) and Inlet Air Temperature Sensor (TA) in Hydrogen Tank
  • RTC function error (Miscalculated Soak Time)
  • FSVSCM failure
  • FCCM failure
Diagnostic Procedure using AutoHex auto Scan tool tester
  • The rear average wheel speed > 15km/h and vehicle speed on the meter<1km/h
  • If the rear average wheel speed > 15km/h and VSP<1km/h lasts for 0.3 seconds, the malfunction is determined.
Test Conditions using AutoHex Scan tool tester
  • Vehicle speed / wheel speed is normal
  • Brake is out of action
  • The automatic brake is out of action
Clear Fault codes Conditions
  • The rear average wheel speed > 15km/h and vehicle speed on the meter<1km/h
  • If the rear average wheel speed > 15km/h and VSP<1km/h lasts for 0.3 seconds, the malfunction is determined.
MIL Status
  • Glow ON


Note:
  • AutoHex is a professional OBD /OBD II diagnostic scanner / scan tool tester.
  • This fault code is a GERENRIC fault code, some cars may change the meaning of this fault code.
    To get the accurate fault code description you may use AutoHex OBD scanner

Oct 24, 2012 | 2010 Audi Q5

1 Answer

Code p1537 foe a 2002 ford ranger 2.3 engine


P1537 - Intake Manifold Runner Control Stuck Open.

You might want to look at the IMRC valve. It is probably sticking from carbon build up? Use top engine cleaner and clean the air plenum.

Once you have done this clear the codes and go for a ride. About 30 miles should do it. If you have anymore codes it will come back up.

Jan 10, 2012 | 2002 Ford Ranger Regular Cab

1 Answer

Code P1537$10 whats code and how do I fix it,it is on a 2002 ford ranger with 2.3 liter engine.


DTC P1537 - Intake Manifold Runner Control Stuck Open Bank 1 and 2

It controls the length and speed of incoming air for a certain engine rpm to optimize swirl, efficiency, and minimize knocking. It's long and fast for low rpm and idle, short and large volume for higher engine loads. How's your truck running? I'm guessing it would be lean at idle if it's stuck open. I would look at your vacuum lines on the intake manifold. I think it would be vacuum operated.

Keep in mind that the IMRC Valves are located on the back of the intake and are listed as an item that the dealer needs to diagnose and repair.

Hope this helps.

Oct 06, 2011 | 2002 Ford Ranger Regular Cab

2 Answers

Code p1537$10 whats code and how do I fix it


DTC P1537 - Intake Manifold Runner Control Stuck Open Bank 1 and 2

It controls the length and speed of incoming air for a certain engine rpm to optimize swirl, efficiency, and minimize knocking. It's long and fast for low rpm and idle, short and large volume for higher engine loads. How's your truck running? I'm guessing it would be lean at idle if it's stuck open. I would look at your vacuum lines on the intake manifold. I think it would be vacuum operated.

Keep in mind that the IMRC Valves are located on the back of the intake and are listed as an item that the dealer needs to diagnose and repair.

Hope this helps.

Oct 06, 2011 | 2002 Ford Ranger Regular Cab

1 Answer

P1537 code


P1537 IS INTAKE MANIFOLD RUNNER CONTROL STUCK OPEN, HOPE THIS HELPS YOU, SEND ME A FEEDBACK PLEASE THANKS . HERES THIS LINK SO YOU CAN CHECK OUT THIS AND LOTS MORE CODES ITS VERY HELP FULL. BUT I CHECK IN MY AUTO MANUAL BOOK ON YOUR VAN IT GIVES ,ME THE SAME CODE.
http://www.obd-codes.com/trouble_codes/ford/
SEND ME A FEEDBACK PLEASE

Aug 02, 2010 | 1998 Ford Windstar

2 Answers

Diagnostic trouble codes P0125,P0601


P0125 OBD-II Trouble Code
Technical Description

Insufficient Coolant Temperature For Closed Loop Fuel Control
What does that mean?

This means that the engine coolant temperature (ECT) sensor indicates that the engine has not reached the required temperature level to enter closed-loop operation within a specified amount of time after starting the engine.
http://www.obd-codes.com/p0125

P0601 OBD-II Trouble Code
Technical Description

Internal Control Module Memory Check Sum Error
What does that mean?

Basically that means that there is an interal fault in the Powertrain Control Module (PCM). There have been many reported PCM failures on Chrysler/Dodge products although it is possible for this to happen on any vehicle. In Dodge/Chrysler products, a P0601 trouble code means that a serial communication failed inside the computer at least 6 times.
http://www.obd-codes.com/p0601

Jan 14, 2010 | 2004 Dodge Stratus

1 Answer

Ford windstar OBD II code P1537/38, P0171 and P0420


It could all be related.P1537/38 are the intake manifold runner controls are stuck open.They are controlled by vacuum solenoids.The P0171 is bank one of the engine is running lean,usually caused by a vacuum leak, P0420 is catalytic converter efficiency code. The computer monitors the switch rate of the front 02 sensors and compares it to the switch rate of the rear 02 sensors to tell if catalytic converter is doing its job. Now if the front 02 is not switching properly then this will cause this test to fail and set this code.
Look on bottom section of the intake manifold at the back of engine(where tranny bolts up) you should see the vacuum motors there on the intake,these are the control motors for the intake manifold runners.Make sure the vacuum lines are hooked up and lines are not leaking. Also you will see a lever from it to intake make sure they move and are not binding.

Mar 11, 2009 | 1996 Ford Windstar

Not finding what you are looking for?
2002 Ford Ranger Regular Cab Logo

345 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...