Question about 1987 Ford Bronco

1 Answer

How do i pack a hub - 1987 Ford Bronco

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 491 Answers

There are bearing packing tools available, but the back yard way to pack a bearing is to fill the palm of your habd with the grease and rool the bearing in the grease so it can fill the bearing cage with the grease

Posted on Oct 11, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do you repack front wheel bearings on a 98 Cherokee 4X4


OP<
Posted by J Sparacino on Aug 31, 2016
you double posted. why do that????
no, the hubs are integrated bearing hubs.
here read the parts pages,
see any tapered bearings there,
if not sold , pray tell , how can you pack the bearing not in hand.
not only that, there are like 1000000 books on how to pack front bearing, if they were removable and are not.
why not look first then post.? at car and the book, !
or read the FREE FSM, it says what ?, unbolt them
and replace the integrated hub assembly.
that is a fact. 300 times ive posted the free book, now.
and is still there, and the words still real ,still jeep words and all accurate. sigh.
below is rockautos list of after market hub assemblies.
do not get confused at those needle bearings, those are actually front axle shaft bearings, not hub wheel bearings. fact.
wheel bearing are ball or tapered rollers, to handle lateral huge loading.

http://www.rockauto.com/en/catalog/jeep,1998,cherokee,4.0l+l6,1315943,brake/wheel+hub,wheel+bearing+&+hub+assembly,1636?a=Referer+duckduckgo.com+URL+%2F

56a4ac86-d271-4704-9005-ab6d4f0bc76f.jpg

Aug 31, 2016 | 1998 Jeep Cherokee 4WD

1 Answer

I have a 83 Bronco 351w I am doing the brakes and the passenger side rotor needs to be replaced can someone walk me through this thanks


Personally I would replace both rotors to prevent a future brake imbalance.

* chock rear wheels, raise front of vehicle and place on stands.

* remove wheels, remove brake calliper and bracket assemblies.

* remove bearing hubs from axles, via removal of bearing adjustment nut

*remove hub seals, clean and inspect bearings, repack with HT bearing grease.

* the brake rotor bolts to the rear of the hub, you will have to remove and replace rotor to hubs, make sure all bolts are thread locked with loctite 263 and tensioned to spec.

* pack hub with grease, install seals, fitt hub assembly and adjust wheel bearing preload, install new split pins.

* fitt brake calliper and brackets, fit new brake pads,

* fitt wheels lower vehicle, test brake for function

Hope this helps..

Aug 02, 2016 | Cars & Trucks

1 Answer

Packing wheel bearings


you cant pack your wheel bearings they are a sealed hub if hub is bad will need to replace the whole unit

Aug 21, 2015 | 2000 Chevrolet Silverado 1500

1 Answer

Packing the wheel bearings on a 98 for Taurus


Just remove the wheel/tire, then remove the dust cap, remove the cotter pin and then remove the nut that holds the brake drum/hub assembly onto the spindle. Then remove the grease seal on the backside of the hub and remove the bearing. Wipe them off, inspect them for discoloration and flaking of the rollers, if good then just pack new grease into the bearings and re-install the bearing into the hub and install a new grease seal, then place the hub/drum back on the spindle and install the outer bearing and the nut, tighten to spec and install the outer nut cotter pin keeper thingy. bend the cotter pin and cut off the excess so the dust cap will fit on and tap it into place. Re-install wheel/tire and torque lugs to spec.

Apr 16, 2011 | 1998 Ford Taurus

1 Answer

How to change wheel bearings on jaguar xj6 front 1996


Disconnect the vehicle battery ground lead.
Support the vehicle at the front and remove the appropriate wheel.
Remove brake caliper and disc assemblies see SRO 70 10
Note- Do not allow the caliper to hang by either harness or
flexible hose.

Pry off the hub grease cap
Remove and discard cotter pin
pull off castellated nut retainer
Remove the hub nut and bearing washer.
Carefully remove the hub assembly from the stub axle.

Pry the original seal from the spigot and discard.
remove the bearings and using a drift punch knock out the bearing cups.
Remove all traces of grease and dirt from the stub axle and back plate.
Note: the backing plate may be used to pull the inner bearing and seal if they stay on the stub shaft.
Press in the new bearing cups using a socket or other tool of the correct size to prevent damaging the new bearing cup or hub.
Note: Do not use bearing to press in the cup.
Pack the annular gaps of the oil seal lips with grease.
Wash the hub assembly thoroughly.
Ensure that the hub inner seal diameter is free of debris or damage and is lightly lubricated prior to assembly.
Only replace complete bearings, never cup or race in isolation.
Pack each race with approximately 4 ml of grease and position the inner race onto the stub axle.
Apply a smear of grease to hub inner surfaces and bearing cups. Assemble the hub to the stub axle followed by outer race, bearing washer and hub nut.
It is not necessary to fill the hub cavity with grease, merely protect from corrosion with a coat of lubricant. Seat the bearings by slightly tightening the hub nut whilst rotating the hub. Do not apply load without rotation.

Adjust End float. Set a Dial Test Indicator and adjust the hub nut to achieve the correct end float.
.001-.003"
As the adjustment is made, continually load the hub axially in both directions.
Without disturbing the end float setting, fit the castellated
nut retainer so that it aligns with both hub nut and stub axle drilling.
Secure nut retainer using a new cotter pin.

Reassemble brake rotor and caliper. Bolts MUST be tightened to specification
operation of the braking system verified.
Reassemble wheel

Dec 25, 2010 | 1996 Jaguar Xj Series

1 Answer

What is needed to remedy right hand front wheel bearing play on a 1990 d21 4X4 ute


replace the bearing or wheel hub assembly.

REMOVAL & INSTALLATION 2wd Models NOTE: Refer to wheel bearing service and bearing preload adjustment procedures found in Section 1.
  1. Raise the front of the truck and support it with safety stands. Remove the wheels.
  2. Remove the brake caliper and suspend it with wire, out of the way. Remove the caliper torque plate if equipped.
  3. Remove the dust cap and then remove the cotter pin, lock washer (if equipped) nut lock and nut.
  4. Pull the hub/disc assembly off the spindle with the outer bearing. Don't let the bearing fall out.
  5. Pry the inner oil seal out and remove the inner bearing. To install:
  6. Clean and inspect the bearings and outer races.
  7. Using a brass drift and a hammer, drive out the bearing outer race. Press a new one into position.
  8. Pack the bearings with grease until it oozes out the other side. Coat the inside of the hub and cap with grease.
  9. Position the inner bearing into the hub, coat the oil seal with grease and press it into the hub.
  10. Press the hub assembly onto the spindle and install the outer bearing and thrust washer.
  11. Install the hub nut. Turn the hub a few times to seat the bearings and then loosen the nut until there is 0mm axial play. Using a spring tension gauge, check that the preload (with new grease seal installed) is 2.2–6.4 lbs. (9.8–28.4N)
  12. Install the lock-nut, new cotter pin and hub grease cap.
  13. Install the brake torque plate. Install the brake caliper.
  14. Install the wheels and lower the truck.
4wd Models The hub and bearing service procedures for a 4wd models are basically the same as those for a 2wd version, with the exception of removing the free running hub assembly and the bearing preload adjustment. Refer to Sections 1 and 7 for additional information. Adjust the preload after the wheel bearing is replaced or the front axle assembly is reassembled. BEARING PRELOAD ADJUSTMENT
  1. Thoroughly clean all parts and pack the wheel bearings.
  2. Apply grease to threaded portions of the spindle, grease seal lip and wheel hub.
  3. Tighten the wheel bearing lock-nut with a socket and torque wrench to 58–72 ft. lbs. (78–98 Nm).
  4. Rotate the hub in both directions a few times to seat the bearings. Loosen wheel bearing lock-nut.
  5. Retighten the lock-nut to 0.4–1.1 ft. lbs. (0.5–1.5 Nm).
  6. Turn wheel hub several times in both directions.
  7. Retighten the lock-nut to 0.4–1.1 ft. lbs. (0.5–1.5 Nm). Fig. 1: Exploded view of the front axle assembly — 2wd models 86718030.gif
    Fig. 2: Removing the bearing outer races 86718032.gif
    Fig. 3: Packing the wheel bearing with grease 86718033.gif
    Fig. 4: Pack the lip cavity of grease seal with grease 86718034.gif
    Fig. 5: Exploded view of the front axle assembly — 4wd models 86718031.gif

  8. Measure wheel bearing axial end-play. The wheel bearing end-play specification is 0.
  9. Install lock washer by tightening the lock-nut within 15–30 degrees.
  10. Turn wheel hub several times in both directions. Wheel bearing should be seated correctly.
  11. If necessary, measure wheel bearing preload. NOTE: Measure wheel bearing preload with a spring-type gauge; measure at wheel hub bolt, with tire removed. The hub assembly should rotate with 1.6–4.7 lbs. (0.73–2.13 kg) of pressure.
prev.gif next.gif

Jul 28, 2010 | 1991 Nissan Pickup

1 Answer

Why cant i turn my manual hubs on a 2000 ford f250?


1 of 2 reasons-- If you have been in the mud, either your hubs are packed with mud and dirt, or your springs are broke inside the hub. Either way, you will probably need to take the hub apart. You will need a 1/4" allen head to take the hub out, after you take the tires off and even the brake assembly.

Apr 07, 2010 | 2000 Ford F250 Super Duty Crew Cabs

1 Answer

Directions replace front wheel bearings on a 1985 nissan stanza?


996fb79.gif

NOTE: After the wheel bearings have been removed or replaced or the front axle has been reassembled be sure to adjust wheel bearing preload. Refer to the Adjustment service procedure below. On the 1989–92 240SX there is just one wheel bearing, pressed into the hub and no adjusting cap. Refer to the exploded views of the Front Axle Hub Assembly. Review the complete service procedure.
  1. Raise and support the vehicle safely.
  2. Remove the front wheels and the brake caliper assemblies. NOTE: Brake hoses do not need to be disconnected from the brake caliper assemblies. Make sure the brake hoses are secure and do not let caliper assemblies hang unsupported from the vehicle.
  3. Work off center hub cap by using thin tool. If necessary tap around it with a soft hammer while removing.
  4. Pry off cotter pin and take out adjusting cap and wheel bearing lock nut.
  5. Remove wheel hub with disc brake rotor from spindle with bearings installed. Remove the outer bearing from the hub.
  6. Remove inner bearing and grease seal from hub using long brass drift pin or equivalent.
  7. If it is necessary to replace the bearing outer races, drive them out of the hub with a brass drift pin and mallet.
  8. Install the outer bearing race with a tool (KV401021S0 special tool number) until it seats in the hub flush. NOTE: Place a large glob of grease into the palm of one hand and push the bearing through it with a sliding motion. The grease must be forced through the side of the bearing and in between each roller. Continue until the grease begins to ooze out the other side through the gaps between the rollers. The bearing must be completely packed with grease.
  9. Pack each wheel bearing with high temperature wheel bearing grease. Pack hub and hub cap with the recommended wheel bearing grease up to shaded portions. Refer to the illustration.
  10. Install the inner bearing and grease seal in the proper position in the hub.
  11. Install the wheel hub with disc brake rotor to the spindle.
  12. Install the outer wheel bearing, lock washer, wheel bearing lock nut, adjusting cap, cotter pin (always use a new cotter pin and O-ring for installation after adjustment), spread cotter pin then install the O-ring and dust cap.
  13. Install the brake caliper assemblies and bleed brakes if necessary. Install the front wheels.

Jun 23, 2009 | 1985 Nissan Stanza

2 Answers

Front rotor needs replacement


if you can't rock the caliper, the you don't need to change the bearing.
yes, we still pack grease. only way to go!

May 15, 2009 | 2001 Ford Expedition

1 Answer

Rear Bearing Problem


These hubs are generally well packed by the manufacturer. If you are going through that hub/bearing at that rate, greasing is likely not your problem as you would see this problem surface with the other hub/bearing as well. Check rear suspension for damage & alignement.

May 02, 2009 | 2005 Toyota Corolla

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77514 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

fordexpert

Level 3 Expert

5627 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...