Question about 2003 Ford Focus

1 Answer

Have a 03 ford focus and seems like i have the codes po 302 and po 316 not sure what could be the problem or what i can do to fix it?

Posted by on


1 Answer

Why is that?
You had the codes pulled,you don't know what they are?

PO302--Misfire on cylinder # 3
Po 316--Disregard,Misfire first 1000 Revolutions.

Posted on Oct 12, 2010

  • Anonymous Oct 12, 2010

    Sorry Cylinder #2



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Codes po 100 andpo404 on a ford focus ghia 2003 many thanks tony

code p0100 indicates a Mass Air Flow circuit malfunction
code p0404 possible egr problems

Dec 07, 2017 | Ford Cars & Trucks

1 Answer

Fault codes PO 193 FRP -- PO 101 MAF -- PO 380 -- PO a 09dc/dc -- PO 238 TURBO/ super charger-- PO 118 ECT -- PO 283 fuel temp sensor -- U 2023 brake sensor

101,380 and 118. These together is a no start. Take it to a garage. Just a guess, but I would be looking into the wiring. You waited to long to have a problem fixed. One bad part over time will lead to many codes. The PCM is trying to adjust to make the engine run right. Throwing other sensor out of range. Out of range pops a code.

Aug 06, 2016 | Ford Cars & Trucks

1 Answer

I have a 03 ford explorer codes p0307 p0316 what could cause that injects good

You have to use Google to find your codes
& study OBD2 Systems
Forget the PO316
The PO 301 thru PO 308 are engine cylinder misfires
On a 2003 --11 year old ford veh you replace ALL
8 COP Ignition Coils
They only last about 6 to 7 years
Some will set a PO300 code
Some with set lots of codes even with just one bad coil
Some coils are so bad they will shut the engine off anytime
& any where under any conditions or temp
There are alos 3 or more ways to diagnose the coils
With no experience & over 7 years on them,buy all 8 coils
from Rock Auto & replace
Also the front Oxygen Sensors get replaced at 100,000
The last number as in your 307 is cylinder #7
Some fords you have
A,B,C,D,E, etc
1,2,3,4,5 etc
PO 301,302,303,304 etc
All 3 examples are the same thing or cylinders

Aug 10, 2013 | Ford Cars & Trucks

1 Answer

Ford focus manual

Fuel grade too low may cause pre ignition or oil passing past the piston rings.

Jan 25, 2018 | Cars & Trucks

1 Answer

03 ford focus dies and locks up while making a right hand turn and A/C is running

Check for a loose wire, when making turn, wire may touch metal and short out system. Check to make sure you did not pinch any wires during the install of transmission.

Apr 05, 2013 | 2003 Ford Focus

1 Answer

03 focus revs out at 50mph code reads shift solenoid

The solenoid is located inside the transmission on the valve body.

Apr 20, 2012 | 2003 Ford Focus

1 Answer

P0720 fault code on 03 focus how do i resolve the problem?

1 st you need to know what code 3 actually is implying Midas or even auto zone will tell you ..but try resetting the obc by removing the positive terminal on the battery for a few minutes then reconnecting it to see it reset itself many cases this will fix the issue unless there is in-depth problems

Sep 06, 2009 | 2003 Ford Focus

1 Answer

Replaced battery in my 03 ford focus now my car stereo will not power on. any procedure to reactivate my car stereo to turn. been reading horror stories about this setup. ugh!!

Not sure if this will help you , but many aftermarket have a reset switch behind the faceplate. would be a small hole about big enough to poke the tip of a ball point pen into.
Also , remove the faceplate and replace it making sure it is clicked in securly.

May 09, 2009 | 2003 Ford Focus

2 Answers

Air bag light keeps coming on in ford focus 03 plate zetec 1.6 wa

Common fault on FORD
Usually due to a poor connection in the YELLOW PLASTIC CONNECTOR underneath the passenger seat.

Just push it together properly and it should clear the AirBag fault

Apr 08, 2009 | 2003 Ford Focus

Not finding what you are looking for?
2003 Ford Focus Logo

Related Topics:

622 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

80637 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

5687 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides