Question about 2004 Isuzu Rodeo
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
SOURCE: Mazda 3 2004 Oxygen Sensor
It calls for a four wire sensor. Try wwwoxygengeek.com call there 1800 number for a thorough listing.Because somtimes they dont list a vehicle on there site.Good Luck!!!
Posted on Aug 04, 2008
from Yahoo answers
The alternator is located on the passenger side of the motor at the bottom. There is a bracket attached to the motor and the alternator. You need not take the bracket off to remove the alternator. Two bolts hold the alternator to the bracket. One bolt is on the front top of the alternator and one bolt is located on the bottom front of the alternator. The bottom front bolt is attached to the tension adjustment for the alternator. Loosen the tension screw then remove the bolt going through the tension adjustment. After you loosen the top, front bolt, the alternator should be loose enough to move side to side. Remove the top, front bolt. Now you must disconnect the alternator from the power supply. Behind the alternator is a screw with a wire attached via nut. Remove this wire. Nextly there is a series of wires with a plug on the end. It is plugged into the side of the alternator. Uplug this item. You can also access both of these from the passenger side front tire well. Something to consider is that remanufactured alternators in Rodeo's as well as the Honda Passport (which has the same engine as the Rodeo) do not work and the problem(s) associated with a bad alternator,ie; not charging, no fan blower, battery light and brake light on, still exsist after replacing alternator with reman. Use a factory original alternator if possible. It will cost a little more than a reman but will most likely save you a lot of time and headache!
Hope this helps you out!!
Posted on Sep 29, 2008
Remove belt, fan, fan shroud and fan bracket. Remove timing covers, timing belt and water pump. Replace timing belt and the hydraulic tensioner with new ones. I suggest you get a mechanic to do this as you can easly get it out of time. Not an easy job.
Posted on Jul 03, 2009
SOURCE: Crank Sensor in 94 Isuzu Rodeo
it's on the bottom of the motor, towards the back on the passenger side. It has a small clip of wires and one screw holding it on. You may want to pull it up on ramps- if it'll run- otherwise, get under the Rodeo, it's up a little higher than the oil pan, and to the passenger side. (it's right on top of the two lines that run to the bottom of the radiator.) You will need a 10mm socket to remove it. I have added a few pics showing the location (i just completed this task myself)
Posted on Jul 24, 2009
Tips for a great answer:
Sep 24, 2016 | 2004 Isuzu Rodeo
Mar 18, 2016 | 2004 Isuzu Rodeo
Oct 20, 2011 | 1993 Isuzu Rodeo
Feb 04, 2011 | 2003 Isuzu Rodeo
Aug 08, 2010 | 1995 Isuzu Rodeo
Dec 03, 2009 | 2004 Isuzu Rodeo
May 12, 2009 | 1999 Isuzu Rodeo
Dec 20, 2008 | 2001 Isuzu Rodeo
May 28, 2008 | 1998 Isuzu Rodeo
Dec 17, 2017 | 2004 Isuzu Rodeo
251 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: