Question about Toyota Tundra

Open Question

How to remove cargo light assembly-2003 tundra

Posted by on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: need to replace cargo & third break light how do i

if its the same as an 06 Tundra, you should be able to remove the lense cover from the back of your truck cab with a screwdriver and pull the light bulbs out...Do not remove the screws below the lense cover that removes the fixture, they have a screw insert that will fall into your truck's body and get lost.....hehehehe I learned that from my own experience...good luck!

Posted on Apr 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why won't my cargo light go off on my 2007 Toyota


Two possibilities:

1. The switch on the light is set to be on all the time.

2. The door switch is not functioning correctly. Find the switch and try depressing it manually and see if you can get the light to turn off. If so, replace the switch.

Apr 05, 2012 | 2007 Toyota Tundra

1 Answer

What do I need to unscrew in the trunk to change the reverse light in my 01 chevy impala


Tail Lamp Assembly Removal & Installation To Remove:
  1. Open the rear compartment.
  2. If equipped, disconnect the cargo net.
  3. Remove the wingnut and pull back the rear compartment trim panel.
  4. Remove the wingnuts from the tail lamp assembly.
  5. Remove the tail lamp assembly from the rear body panel.
  6. Disconnect the electrical connector from the tail lamp assembly.
  7. Remove the tail lamp socket by turning counterclockwise.
  8. Remove the side marker lamp socket by turning counterclockwise.
To Install:
  1. Install the side marker lamp socket by turning clockwise.
  2. Install the tail lamp socket by turning clockwise.
  3. Connect the electrical connector to the tail lamp assembly.
  4. Position the tail lamp assembly to the rear body panel.
  5. Install and secure the wingnuts that attach the tail lamp assembly to the body panel.
  6. Position the rear trim panel to the rear compartment. Install and secure the wingnut.
  7. If equipped, connect the cargo net.
  8. Close the rear compartment.
prev.gif next.gif

Oct 18, 2010 | 2001 Chevrolet Impala

1 Answer

I can't figure out how to get my 2003 Tundra taillight assembly off . I have removed the two bolts inside the tailgate area but it is still attached to the fender on the other side of the assembly . I have...


Unscrew the screws that are securing the brake light cover to the body of the Tundra. Pull the brake light cover off the body of the Tundra. Place the screws in the brake light cover and set it on the bed of the truck. Pull the burned-out light bulb out of the light fixture and discard it. Insert the new brake light bulb into the light fixture. Pump the Tundra's brakes to make sure the new bulb is working correctly. Replace the brake light cover on the body of the Tundra and replace the screws.

Sep 09, 2010 | 2003 Toyota Tundra

1 Answer

Remove & replace right turn signal bulb


The procedure is as follows:-- Working from the trunk:
1. locate the 2 retaining knobs (doohickeys that you fasten the trunk cargo net to) for the Hard plastic trunk liner near to and inside of the rear light assembly. Unscrew the knobs.
2. Pulling back the plastic liner, locate the 4 studs (threaded posts). 3 will be located vertically in a line, the fourth, outboard and lower. Using a 10mm wrench(small), remove 3 of the 4 nuts fastening the light assembly to the body. DO NOT remove the lowest nut of the 3 in a vertical line, as this does not fasten the light assembly. DON'T LOSE THE NUTS OR WASHERS.

Working from the rear of the car:
1. Hand pull the light assembly from the car body.
2. Remove bad lamp. Twist lamp socket and pull out of assembly. Pull lamp and replace with #3057.
Reassemble:
1. Test light prior to reassembly.
2. Ensure Gasket material for assembly and studs is intact, this keeps water/dust out and dampens movement (prevents rattling and increases the life of lamp).
3. Use Reverse instruction for reassembly.
-------------- The taillight/backup light/license plate light assembly is separate from the brake light/turn signal light assembly on the Buick LeSabre. No matter what rear bulb you have to replace, you must access the trunk area to do so. Open the trunk of the Buick LeSabre.Locate 7 nuts underneath the trunk lid (3 on each end of the trunk lid and 1 in the middle). Remove each one using a nut driver.Manipulate the trunk lid at chest level and gently pull the rear taillight assembly slightly away from the trunk lid.Locate the burned out bulb sockets and then remove the bulbs. Insert the new bulbs into the socket and test by turning on the lights before reassembling.Replace the tail light assembly by aligning the studs inside the predrilled holes in the trunk lid. Refasten the 7 nuts.Remove the cargo net if applicable to replace the brake and/or turn signal light.Unscrew the plastic wingnut that the cargo net is attached to. Pull back the trunk liner.Remove the 2 plastic wingnuts under the trunk liner.Pull the brake light assembly outward from the back of the LeSabre.Locate the socket of the burned out bulb and then turn counter clockwise 1/4-inch to release it from the assembly.Remove the old bulb from the socket and replace with a new one. Test the light before reassembling. Thanks. Keep updated for any more query. You can rate this solution and show your appreciation.

Aug 07, 2010 | Buick LeSabre Cars & Trucks

1 Answer

Cargo brake light works but my rear brake lights dont. reverse and turn signals work fine. 04 silverado


check wiring harness behind light assembly for a loose or broken ground wire. this would not affect the third or "cargo" brake light

Apr 22, 2010 | 2003 Chevrolet Silverado 1500

1 Answer

2003 Toyota Tundra Limited Stepside truck. No brake light. But the 3rd brake light works. Already checked the 15 amp fuse by the steering column


Hello.

We would suggest that you look at the wiring connector under the bed, that feeds the taillamps.

You will probably find a coroded wire in the connector. If the 3rd brake lamp works, all of the fuses and switches are good.

Dec 25, 2009 | 2003 Toyota Tundra

2 Answers

Left rear turn signal bulb is burned out.


Tail Lamp Assembly
Removal & Installation
To Remove:

  1. Open the rear compartment.
  2. If equipped, disconnect the cargo net.
  3. Remove the wingnut and pull back the rear compartment trim panel.
  4. Remove the wingnuts from the tail lamp assembly.
  5. Remove the tail lamp assembly from the rear body panel.
  6. Disconnect the electrical connector from the tail lamp assembly.
  7. Remove the tail lamp socket by turning counterclockwise.

  1. To Install:
  2. Install the tail lamp socket by turning clockwise.
  3. Connect the electrical connector to the tail lamp assembly.
  4. Position the tail lamp assembly to the rear body panel.
  5. Install and secure the wingnuts that attach the tail lamp assembly to the body panel.
  6. Position the rear trim panel to the rear compartment. Install and secure the wingnut.
  7. If equipped, connect the cargo net.
  8. Close the rear compartment.
      Please don't forget to rate !!!!!!

    Mar 28, 2009 | 2002 Buick Century

    2 Answers

    Need to replace cargo & third break light how do i


    if its the same as an 06 Tundra, you should be able to remove the lense cover from the back of your truck cab with a screwdriver and pull the light bulbs out...Do not remove the screws below the lense cover that removes the fixture, they have a screw insert that will fall into your truck's body and get lost.....hehehehe I learned that from my own experience...good luck!

    Mar 04, 2009 | 2008 Toyota Tundra

    1 Answer

    CARGO LIGHT


    Switch in top in front of mirror.

    Jun 30, 2008 | 2006 Toyota Tundra

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    117 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Toyota Experts

    yadayada
    yadayada

    Level 3 Expert

    75807 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22133 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8172 Answers

    Are you a Toyota Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...