Question about 1994 Mazda B-Series

Open Question

Torque value and sequence for head bolts ..1994 B4000

Posted by on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 30 Answers

SOURCE: Torque on 1994 Mazda pick up

if its a four cylinder(lets hope)the specs are 80-90ft.lbs torque.if its a six cylinder it is 14ft.lbs torqueat 90 degree intervals then repeat until correct torque has been reached.bad news is you can not use the same bolts on the six cylinder engine.have to be new to keep from breaking them

Posted on Mar 15, 2009

Ad
inspectmycar
  • 233 Answers

SOURCE: 94 mazda B3000 3.0L cylinder head torque specs

Step 1 torque to 59 ft pounds
2. Loosen one full turn
3. 37 ft pounds
4. 68 ft pounds

Use torque sequence below
aca9f77.gif

Posted on Sep 17, 2009

SOURCE: Where is the fuel filter on a 1994 Mazda b4000 pickup?

Driver side frame rail right where the door is. It's held in by a large hose clamp. It has 2 white plastic clips . 1 on each hose of the filter. When removing have a container that can hold gas ready because about a pint of gas will come out. Make sure new filter comes with new clips. I don't recommend using old ones. After new one in place turn key on and leave in run position for 20 seconds so filter can gill with fuel before starting and inspect fir leaks.

Posted on Apr 08, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the torque settings for a mitsubishi colt hiline 2.0i cylinder head?


There is no torque value. Commonly, Head bolts are tightened and then removed in sequence as you step threw 3 values: 23/33/45 ft lbs then the final value is achieved by rotating the bolts 90 degrees so the final value is unknown.

You have to get either a hayes manual or follow a procedure online if you are replacing the head gasket. If you are not replacing the gasket do not "re-torque" the head bolts thinking that you can fix a head gasket leak.

Jul 29, 2014 | 2005 Mitsubishi Colt 1.1

1 Answer

Workshop manual for a 1994 nissan serena


Cylinder head bolt torque sequence
The Rod Bearing Cap Torque
The Main Bearing Cap Torque 38 Foot pounds (Final torque)


Step 1: Torque 10-12 Ft/LbsStep 2: Torque 17-21 Ft/Lbs


Note :
Torque sequence ------------------------
' 11 '
front ' 13 9 3 1 6 8 '
of ' '
engine ' 14 7 5 2 4 10 '
' 12 15 '
------------------------
Step 1: Torque all bolts in sequence 22 Ft/Lbs
Step 2: Torque all bolts in sequence 47 Ft/Lbs
Step 3: Loosen all bolts in reverse sequence
Step 4: Retorque all bolts in sequence 22 Ft/Lbs
Step 5: Retorque all bolts in sequence 43-51 Ft/Lbs
Step 6: Retorque bolts 11 thru 15 in sequence an
additional 4-6 Ft/Lbs
** CAUTION ** This engine uses 2 different length head
bolts. "#1" Is the long bolt, while remaining bolts
are short. **Do not confuse location of these bolts**
recheck final torque in sequence

Dec 06, 2012 | Cars & Trucks

1 Answer

Head bolt sequence and torque values on a 1999 Chevy 3.1L engine


if the 8th number om your VIN is a "J" then this is the correct prossess 3.1LTorque sequence --------- ' 6 2 3 7 ' ' 5 1 4 8 ' --------- Step 1: torque in sequence to 37 Ft/Lbs Step 2: turn an additional 90 degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.Always coat bolt threads with the proper sealant.

if the 8th number on your VIN is a "M" then this is the correct prossess 3.8LTorque sequence --------- ' 6 2 3 7 ' ' 5 1 4 8 ' --------- Step 1: torque in sequence to 37 Ft/Lbs Step 2: turn an additional 90 degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.Always coat bolt threads with the proper sealant.

Oct 12, 2011 | 1999 Chevrolet Malibu

1 Answer

What is the torque settings on a 3.4 liter engine 94 camaro. replaced the heads and gaskets


Torque sequence --------- ' 6 2 3 7 ' ' 5 1 4 8 ' --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.

I hope this helps you and good luck

Mar 25, 2011 | 1994 Chevrolet Camaro

1 Answer

Correct pressure for torque the head of mazda pickup 1998


Since you didn't say which engine you have, I've pulled torque specs for 3 different engines. Also, since I can't include a diagram showing the relative locations of the numbered head-bolt locations, it would be a good idea for you to purchase a vehicle specific repair guide that will show this info.


Take particular note about the TTY (Torque to Yield) bolts used on 2 of the 3 engines shown. It is said that new head bolts MUST BE USED when head is replaced or re-installed to obtain the proper torque.



B2500 4 Cylinder

Torque sequence: --------- ' 10 6 2 4 8 ' front ' ' ' 7 3 1 5 9 ' -----------Step 1: torque in sequence to 51 Ft/Lbs Step 2: torque again in sequence to 51 Ft/Lbs Step 3: final tighten all bolts an additional 90 to 100 degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.







B3000 3.0 6 Cylinder

Torque sequence ---------- ' 6 4 2 8 ' ' ' ' 5 1 3 7 ' ---------- Step 1: torque to 59 Ft/Lbs Step 2: loosen in sequence (1) full turn Step 3: torque to 41 Ft/Lbs Step 4: torque to 73 Ft/Lbs









B4000 4.0 6 Cylinder

Torque sequence --------- ' 5 1 3 7 ' ' ' ' 6 4 2 8 ' --------- Step 1: torque cylinder head bolts in sequence to 26 Ft/Lbs Step 2: torque cylinder head bolts to 56 Ft/Lbs Step 3: turn cylinder head bolts in sequence an additional 90-degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.


Good luck with this job!

Feb 06, 2011 | 1998 Mazda Pickup

1 Answer

What is the torque on the head bolts and sequence on a 760 volvo 2.3 turbo


The head torquing sequence for any cylinder head is as below, continue the pattern if there are more than 10 bolts:-


10 6 1 3 7

8 4 2 5 9

Start at the middle two bolts and do your sequence at least three times, first at about half the torque, then the full torque value at least twice. It is good practice to re torque the head again after about 1000 km (600 miles), but this is often disregarded due to the problems of getting to the head bolts.

Jan 29, 2011 | 1988 Volvo 760

1 Answer

What is the toqrque spechs and order for a Northstar 4.6 engin for both head and main & rod barngs. Does the main barnings have a order


If you have to pull a cylinder head on a 1993-1999 4.0L or 4.6L Northstar V8 to replace a gasket or do a valve job, do not reuse the old 11mm head bolts. Also, GM has revised the head bolt torque values and tightening procedure as follows:
  1. In sequence, torque all bolts to 30 ft.-lbs.
  2. In sequence, rotate all bolts an additional 70 degrees.
  3. In sequence, rotate all bolts an additional 60 degrees.
  4. In sequence, rotate all bolts another 60 degrees.
  5. Torque the front three M6 head bolts to 106 in.-lbs.

Dec 09, 2010 | 2003 Cadillac Seville

1 Answer

Need torque specs for 1994 ford escort 1.9 ltr head bolts


Torque new cylinder head bolts in sequence to 44 ft lb. Loosen bolts approximately two turns, then torque bolts in sequence to 44 ft lb. Turn bolts an additional 90 degrees in sequence, then an additional 90 degrees

Torque sequence
9 3 1 5 7
8 6 2 4 10

May 07, 2010 | 1994 Ford Escort

1 Answer

I am looking for the cylinder head torque specification for the 3.3litre chrysler town and country 2003


Tighten the cylinder head bolts 1 - 8 in the sequence shown in Cylinder Head Bolts Location and Tightening Sequence Using the 4 step torque turn method, tighten according to the following values:
Step 1: Bolts 1 - 8 to 61 N·m (45 ft. lbs.)
Step 2: Bolts 1 - 8 to 88 N·m (65 ft. lbs.)
Step 3: Bolts 1 - 8 (again) to 88 N·m (65 ft. lbs.)
Step 4: Bolts 1 - 8 turn an additional 1/4 Turn. (Do not use a torque wrench for this step.)
NOTE: Bolt torque after 1/4 turn should be over 122 N·m (90 ft. lbs.) If not, replace the bolt.

Tighten head bolt number 9 Cylinder Head Bolts Location and Tightening Sequence to 33 N·m (25 ft. lbs.) after head bolts 1 - 8 have been tighten to specifications.

Jan 24, 2010 | 2003 Chrysler Town & Country

1 Answer

Need to know cylinder head bolt torque specs


Head Bolt Torque For your 1994 Oldsmobile Cutlass Supreme (3.4L SFI DOHC): clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 6 2 3 7 | | 5 1 4 8 | --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque. clearpixel.gif clearpixel.gif clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 8 4 1 5 | | 7 3 2 6 | front --------- of engine | 6 2 3 7 | | 5 1 4 8 | Step 1: torque to 40 Ft/Lbs --------- Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.

Feb 07, 2009 | 1994 Oldsmobile Cutlass Supreme

Not finding what you are looking for?
1994 Mazda B-Series Logo

Related Topics:

74 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...