Question about 1999 Oldsmobile Aurora

1 Answer

How do we compress the rear brake calipers when replacing the pads?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 15 Answers

Get a pad spreader or C-clamp leave the old pad on the piston and compress it. If you have a strong grip big channel locks will also work

Posted on Oct 11, 2010

  • atrtigs2 Oct 18, 2010

    caliper piston must be turned to compress don:t know witch way?

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Steps to replacing rear brake pads


A special tool is required to compress the caliper piston on the rear brakes-don't use a C-clamp on the piston.
Raise the vehicle and remove the tire. The rear calipers have only one guide pin. Remove this pin and raise the caliper. Remove the old brake pads. Using the special tool compress the caliper piston-the piston will have one or two slots on it. These slots must in the correct position to remount the caliper. Install the new brake pads and slide the caliper back over the rotor and replace the guide pin. If the caliper doesn't slide over the rotor you'll need to reset the slots on the piston. Replace the tires and you're ready to go.

Jan 01, 2011 | 2000 Buick LeSabre

1 Answer

How to replace rear brake pads on 2002 buick rendevous


Those are special calipers. The piston cannot be just compressed back into the caliper - it needs to be turned as it is compressed or you can ruin the caliper.There is a kit you can rent from AutoZone or many independent auto parts stores that will perform both functions at the same time.
Block fron wheels and raise vehicle passenger side. Remove wheel. The caliper is on the top rear side of the assembly you're looking at.There are 2 long bolts you'll need to remove to take the caliper off the vehicle. Don't remove the brake line or open the bleeder screw ( either of these moves will add to your work!! ) Insert a large flat blade screwdriver in between the rotor and outboard brake pad and pry away from the vehicle slightly to release the pads from the rotor. Slide caliper upwards and towards the back of the vehicle to separate from rotor. The pads will come in a full set ( all 4 pads for both side of the rear ) . Look at your replacement pads and determine if they have a retainer clip holding them in place or a compression clip. Remove outboard pad first then inboard. Match old pads to replacement pads. Inspect rotor for grooves and irregular surfaces - if any grooves or irregularity present, remove rotor and take to an auto parts store for refinishing.Compress caliper piston with kit and allow 5 minutes for pressure to bleed back into the master cylinder.install rotor if removed and wipe surfaces with brake clean. Install inboard then outboard pad and place caliper on rotor, then mount to vehicle. Install wheel, repeat procedure for drivers side, then PUMP BRAKE PEDAL 5 TIMES BEFORE TRYING TO DRIVE VEHICLE to set pads on rotors.

Nov 26, 2010 | 2003 Buick Rendezvous

1 Answer

What tools needed to replace front brake pads & rotors


Brake Pads
Removal & Installation
Front





3.4L front disc brake assembly
toy_4run_34_frontbrakeassembly.gif








4.0L and 4.7L front disc brake assembly
toy_4run_frontbrakeassembly.gif



To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Front wheel
    • Clip, 2 caliper pins, the anti-rattle spring then remove the 2 brake pads
      and the 4 anti-squeal shims

To Install:

CAUTION
Only replace brake pads on 1 side of the
vehicle at a time. Failure to use this procedure could cause the caliper pistons
on the opposite side of the vehicle to pop out requiring the reconditioning or
replacement of the brake caliper.


  1. Remove a small amount of brake fluid from the master cylinder.
  2. Install a used brake pad into the caliper and compress the caliper pistons.
  3. Apply disc brake grease to both sides of the inner anti-squeal shims.
  4. Install or connect the following:

    • Anti-squeal shims to the new brake pads
      NOTE: When replacing worn pads, the anti-squeal shims must be replaced
      together with the pads.

    • 2 brake pads
    • Anti-rattle spring and the 2 caliper pins
    • Clip
    • Front wheel

  5. Depress the brake pedal several times to seat the brake pads.
  6. Check the brake fluid level and top off as needed.

Rear
To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Rear wheel






      toy_4run_rearcalbolts.gif



    • 2 cylinder slide pins from rear caliper assembly
    • Caliper assembly from rear caliper mounting
    • 2 brake pads with anti-squeal shims from rear caliper mounting
    • 2 anti-squeal shims from each disc brake pads
    • Pad wear indicator plate from the inner side disc brake pad
    • 4 pad support plates from the rear caliper mounting

To Install:


  1. Install or connect the following:

    • 4 pad support plates on the rear caliper mounting
    • Pad wear indicator plate on the inside brake pad
      Note: Install the pad wear indicator facing downward.

    • Anti-squeal shims on each brake pad
    • 2 disc brake pads with anti-squeal shims to the caliper assembly

  2. Apply lithium soap base glycol grease to the sliding part of 2 caliper slide
    pins.
  3. Install or connect the following:

    • Disc brake caliper assembly with 2 caliper slide pins
    • Torque to 65 ft-lbs (88 Nm)
    • Rear wheel

  4. Depress the brake pedal several times to seat the brake pads.
  5. Check the brake fluid level and top off as needed.
--- Removal & Installation
Front
To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Front wheel
    • Front brake caliper assembly

  3. Make matchmarks on the disc and the axle hub.
  4. Remove the front disc.

To Install:


  1. Align matchmarks and disc onto axle hub.
  2. Install or connect the following:

    • Front brake caliper assembly with the 2 bolts

      1. Torque to 90 ft-lbs (123 Nm)

    • Front wheel

Sep 23, 2010 | 2003 Toyota 4Runner

2 Answers

I cant seem to get the rear brake caliper to compress so it will fit over the new pads


There are two stlyes of calipers for the rears. One is ratcheting so the piston has to be turned back to colaspe. The other type compresses with a C clamp. If a large retaining spring is on the inner part of the caliper you have the ratcheting type. A brake cable will attach to the spring as well. If not it will compress instead

Apr 10, 2010 | 2004 Mazda 6

3 Answers

Changing the front brake pads on a 2006 Pontiac Montana SV6


no that is only the older rear calipers on gm and others. the fronts do not have that style caliper and sound like the calipers are frozen and may be way your changing the pads. try opening the bleeder screw and then compressing them if they go then you need need brake hoses and if not you need calipers. god luck man

Dec 13, 2009 | 2005 Pontiac Montana SV6

1 Answer

I can't seem to compress calipers for replacing rear disc brake pads, why?


open the blled valve and try to compress, if it does not compress make sure your emergency barke is not on, if it's not on then compress calipers if it won't compress you may have a sticking caliper,if sticking remove one caliper and push the brake pedal down it should dislodge the stuck brake caliper if not you have a bad master cylinder check valve.

Jun 13, 2009 | 1994 Oldsmobile Cutlass Supreme

1 Answer

How to replace rear brake pads


Jack up car, remove wheel. There are two bolts that hold the caliper on. Remove these. Caliper comes off, take old pads out. There is a special tool to compress the piston back into the caliper (do not use a C Clamp on the rears.) Put new pads back on, re-install the caliper, and put the wheel back on. Pump the brake pedal until it is firm. Done.

May 27, 2009 | 2006 Ford Focus

1 Answer

I am replacing the rear pads and cannot get the caliper to compress using a c-clamp. Is there something special I need to do or know on my montego 05 car to get the caliper to compress? Sincerely Desperate...


One, take your brake fluid reservoir cap off.
Two, use a thin piece of wood to help you compress the piston on the caliper....do it slow. This way, you don't create a lot of pressure to the reservoir and it won't overflow.
Three, these are the steps to removing and replacing the pads for the rear. It does mention a special tool....but you can use a c-clamp for the same purpose:

Rear To Remove:
  1. Check the brake fluid level in the brake master cylinder reservoir.
  2. If required, remove the fluid until the brake master cylinder reservoir is half full. CAUTION
    Care must be taken when servicing rear brake components without disconnecting the parking brake cable from the brake caliper lever.
  3. Remove the disc brake caliper. Support the caliper with mechanic's wire. CAUTION
    When the brake pads are separated from the brake caliper, new brake pads must be installed. The brake pads are one-time use only.
  4. Remove and discard the brake pads and spring clips from the brake caliper anchor plate. NOTE: Do not remove the anchor plate guide pins. The guide pins are press fit to the brake caliper anchor plate. If the guide pins are damaged a new anchor plate must be installed.
  5. Inspect the brake caliper anchor plate assembly.
  6. Check the guide pins and boots for binding or damage.
  7. Install a new brake caliper anchor plate if it is worn or damaged.
To Install:
NOTE: The left caliper piston turns clockwise and the right caliper piston turns counterclockwise.
  1. Using the special tool, turn and compress the brake caliper piston into the cylinder.
  2. Clean the residual adhesive from the brake caliper fingers and pistons using the specified brake parts cleaner. CAUTION
    Do not allow grease, oil, brake fluid or other contaminants to contact the brake pad or caliper mating surface. Do not install contaminated pads.
    NOTE: Install all the new hardware supplied with brake pad kit.
  3. Install the new spring clips and brake pads.
  4. Position the brake caliper and install the 2 bolts. Tighten caliper bolts to 23 ft-lbs (31 Nm).
  5. If necessary, fill the brake master cylinder reservoir with clean brake fluid.
  6. With the engine running, apply pressure on the brake pedal to seat the brake pads.
  7. Test the brakes for normal operation.

May 17, 2009 | 2005 Mercury Montego

4 Answers

Replace rear brake pads on a 2000 grand marquis


rate as fixya if this is what you need. Thanks

  1. Remove the rear disc brake caliper (2K327).
  2. Remove the brake caliper bolts.
  3. Lift the rear disc brake caliper off the rear disc brake caliper anchor plate (2B582).
  1. sya~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not allow grease, oil, brake fluid or other contaminants to contact the brake pads.
    Remove the brake pads by pushing inward and rotating the pad up.
  1. NOTE: Use a block of wood or used pad to protect the piston and boots.
    Retract the caliper piston (2196) into the rear disc brake caliper.
cf7b02c.gif

Mar 15, 2009 | 2000 Mercury Grand Marquis

Not finding what you are looking for?
1999 Oldsmobile Aurora Logo

Related Topics:

167 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...