Question about 2003 Jaguar S-Type
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
i know when i programed my '98 XJ8L... i had to use the sender button on the actual opener mounted on the garage roof and not the hand-held remote... not sure if that helps
Posted on Jan 08, 2009
You must charge the battery or you can use jumper cables from another battery to your battery to activate the electric trunk release, just be sure you hook up the jumper cables correctly ( cable to + on the battery and black to _ terminal of battery)and wear safety glasses when hooking up cables this should release the trunk. Also as a precaution always hook up + or red jumper cables wires first to prevent a arcing spark which is not terribly dangerous but this order in which to connect jumper cables is recommended.
Posted on Oct 10, 2009
Homelink Garage Door Opener Programming Procedure:
The procedure described below was successfully applied to a 2005 Jaguar S-Type.
To begin with, several attempts were made using the programming instructions contained in my Jaguar’s owner’s manual. Though the procedure described in the owner’s manual was straight-forward and understandable, I was unsuccessful in getting the vehicle’s remote to make my garage door opener function. The particular garage door openers I have are both made by Genie. Both openers utilize the “Rolling Code” feature.
To begin with, be sure to clear previous codes on your Jaguar’s garage door opener by first turning (rotating) the ignition key to the “I” position (first notch). Next, simultaneously hold button 1 (left most button) and button 3 (right most button) down until the middle button’s red light changes from continuous on to a rapid flash. This process takes approximately 20-25 seconds. What follows is a two part process. In the first part, get your Genie portable remote and hold it near (approximately 3 inches away from) your Jaguar’s garage door opener console buttons. Choose which button on your Jaguar’s remote you wish to dedicate to your Genie door opener and simultaneously press and hold your Genie opener button and your Jaguar’s opener button. The red light on your Jaguar’s center button (button #2) will light up and within 1-2 seconds will begin to flash rapidly. You have just completed part 1 of the two part process.
Part two: Now it is time to utilize the “Learn” function on your Genie garage door opener. Press the “Learn” button on your Genie garage door opener. The red LED adjacent to the “Learn” button will begin to flash. You now have 30 seconds in which to program your Jaguar’s opener button. Using the same button you just used in the “part 1” procedure, press and hold the same button for several seconds. As before, your Jaguar’s red light in the middle button will light up and within 1-2 seconds, it will flash rapidly. Release the button you are programming. Now, here is the key piece of information! Once again, press and hold that same button. Once again, the center button’s red light will flash rapidly. Release your newly programmed button. This procedure proved successful in my application. Here is what has just happened. The first time you pressed your Jaguar’s remote button tells the Genie opener that it exists and that it is a viable candidate for making your life easier (opening the damn door). The second time you press your Jaguar’s remote button confirms to the Genie’s rolling code that your Jaguar’s signal is legitimate and is to be trusted from then on.
Posted on Dec 23, 2009
THEY MAKE THE SYSTEM AND HAVE INSTRUCTIONS YOU CAN DOWNLOAD.
PLEASE NOTE: NOT ALL BRANDS/MODELS OF OPENER WILL WORK WITH THIS SYSTEM.
HOPE THIS HELPS
Posted on May 27, 2010
If you can get the hood open, then look for the alternator and use the heavy gauge single wire. Put the (+) of the charger on it and the (-) on a good ground.
Posted on Dec 12, 2010
Tips for a great answer:
Jul 31, 2012 | 2003 Jaguar X-Type
Dec 12, 2010 | 2003 Jaguar S-Type
Apr 21, 2009 | 2000 Jaguar S-Type
Jan 04, 2009 | 1998 Jaguar XJ8L
Nov 24, 2008 | 1998 Jaguar XJ8L
Sep 30, 2008 | 2003 Jaguar XJ-Series
Jun 06, 2008 | 2003 Jaguar XJ-Series
156 people viewed this question
Usually answered in minutes!