Question about 2000 Ford Windstar

1 Answer

How to change torque converter clutch a on 2000 windstar

Posted by on

1 Answer

Remove Transaxle,install rebuilt converter or have yours rebuilt

Posted on Oct 12, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

P0741


P0741 Ford - Torque Converter Clutch Mechanical System

The Engine Control Module (ECM) detected excessive transmission slippage or no TCC solenoid operation. Check the transmission converter clutch selonoid. can be low on transmission fluid, clogged filter.

Dec 10, 2013 | 2000 Ford Windstar

1 Answer

P0740 honda odyssey


P0740 Honda - Transmission Lock-Up Control System Fault Possible causes
- Low transmission fluid level
- Dirty transmission fluid
- Faulty torque converter clutch solenoid valve
- Torque converter clutch solenoid valve harness is open or shorted
- Torque converter clutch solenoid valve circuit poor electrical connection

Tech notes
On some Honda vehicles the P0740 code may be set by an overheating torque converter problem which is caused by an insufficient flow to the torque converter release circuit.

P0740 Honda Description
The torque converter clutch solenoid valve is activated, with the gear in D4, by the Transmission Control Module (TCM) in response to signals sent from the vehicle speed and the Engine Control Module (ECM). Lock-up piston operation will then be controlled. When the torque converter clutch solenoid valve is activated, the torque converter lockup clutch will engage creating a 1 to 1 RPM ratio between the transmission input shaft and the rotational speed of the torque converter.
Lock-up operation, however, is prohibited when A/T fluid temperature is too low.
When the accelerator pedal is depressed (less than 2/8) in lock-up condition, the engine speed should not change abruptly. If there is a big jump in engine speed, there is no lock-up.

Dec 04, 2013 | 2000 Honda Accord

1 Answer

PO743 1999 ford windstar 3.8


THAT CODE P0734 IS A TCC (TORQUE CONVERTER CLUTCH) TROUBLE CODE. EITHER THE WIRING GOING INTO TORQUE CONVERTER SOLONOID ARE LOOSE OR THE SOLONOID ITS SELF IS BAD.

Jun 09, 2012 | 1999 Ford Windstar

1 Answer

What's your problem?Torque Converter Clutch electrical circuit kia optima 2009


This is a common GM Problem. The automatic torque converter clutch circuit is located inside the ****** and helps with smoother shifting. If it is faulty unplug the harness until the clutch circuit is repaired

Jun 04, 2012 | 1998 Ford Windstar

1 Answer

My 2000 ford windstar was working fine, then I stopped to put gas and when I tried to switch from park to drive it did not go in gear. no reverse, no drive, what would it be??


Hi hope I can help.
This is a very common way that a torque converter fails.
The transmission will need to be removed and a new torque converter installed.
Hope this helps
leave feed back
thank you urnuts73@fixYa

Mar 05, 2011 | 2000 Ford Windstar

2 Answers

2000 windstar transmission code 715 turbine speed sensor need to replace, where is it and should I do it.


turbine speed sensor is the torque converter speed ,but where and how it works i do not know,i would buy a manual vehicle nyself at least it doesnt cost the earth when the clutch wears out

Jul 16, 2010 | 2000 Ford Windstar

2 Answers

Will a transmission #ax4s from 1988 ford windstar fit a 200 windstar with transmission # ax4s


I dont think that will work ....1988 was aod and aode trans

The AXOD-E was renamed AX4S in 1993. In addition to the name change, improvements in the lubrication of the gearset and capacity upgrades were made. A centrifugal piston assembly was implemented in the intermediate clutch position to improve 1st-2nd and 2nd-1st shift quality and an increase in the clutch's durability was made on some models. High energy friction materials were also introduced. A new twin piston torque converter clutch (TCC) was introduced with the AX4S and the AX4N on some models. The transaxle pan on this model will sometimes read "AXOD Metric" since it's based on the AXOD transaxle. The data plate code for this transmission is "L."
Applications:
The Ford AX4S automatic transmission is a four-speed electronic overdrive transmission used in 1995 to 2000 Ford Windstar minivan. The transmission is also used in 1991 to 2003 Ford Taurus and Mercury Sable, and 1993 to 1995 Ford Taurus SHO models. The AX4S is a second-generation version of the AXOD and AXOD-E transmissions used in 1986 to 1991 Ford Taurus.

Nov 16, 2009 | 2001 Ford Windstar

2 Answers

My 02 3.8 windstar starts chugging down at redlights. i have changed the idle air control, the plenum gasket, and the egr valve


Chugging down? Do you mean your engine is almost stalling? Sounds like your fuel filter is clogging up. Change it before your fuel pump dies. A Fuel Filter's like $10 - $15.

May 04, 2009 | 2000 Ford Windstar

1 Answer

Emissions test code comes up as 0743 torque converter circuit problem. how do you fix this on a 1998 ford windstar 3.8l engine?


U have a problem in the transmission torque converter clutch control circuit, most likely the solenoid switch that applies the lock up clutch of the torque converter is defective or a the torque converter itself is defective, the trans pan will need to be removed to check the problem further.

Mar 09, 2009 | 1998 Ford Windstar

Not finding what you are looking for?
2000 Ford Windstar Logo

Related Topics:

286 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5481 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...