Question about 2002 Jeep Liberty

Open Question

2002 Jeep Liberty Ltd (2-wheel drive): Front right turn signal lamp, rear right tail light lamp, and dash lights all went out simultaneously when I hooked a U-Haul trailer up to my trailer hitch electrical system. The bulbs in the front and rear lights are working because I was able to pull the trailer with the emergency flashers on. Is this a crimped wire somewhere in the system, or is this a fuse story?

Posted by on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
pippall
  • 1486 Answers

SOURCE: No running lights on my trailer, but stop and flashers work

Remove trailer plug and check the wire has not broken.inside..

Posted on Jun 11, 2009

Ad
rogrrabbit
  • 986 Answers

SOURCE: need a tail light wiring diagram for 2005 Jeep Liberty

I advice you don’t cut into the wiring harness but get the proper kit that is plug and play.

Posted on Jun 14, 2009

heavymetal77
  • 721 Answers

SOURCE: I am installing a trailer hitch on my 2001 dodge

They came with factory installed towing harnesses. No need to install aftermarket stuff. The harness is in the left(driver side} rear panel. All you need to do is plug it in.

Posted on Jun 22, 2009

  • 118 Answers

SOURCE: install trailer hitch wiring kit

Sould be a simple plug in harness under rear of vehicle

Posted on Mar 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

08 Buick lucerne cxl. Third brake light works as well as front signal lights. No rear brake lights or turn signals. Tail lights and headlights and third brake lights works. Bulbs good. Help


Stop Lamps
The brake pedal position sensor is used to sense the action of the driver application of the brake pedal. The body control module (BCM) provides a 5-volt reference voltage and low reference to the brake pedal position sensor. The position sensor provides an analog voltage signal back to the BCM that will increase as the brake pedal is applied. When the brake is applied, the BCM will then apply battery voltage to the left and right stop/turn signal lamp supply voltage circuits and the center high mounted stop lamp (CHMSL) supply voltage circuit illuminating the stop lamps. At the same time the BCM applies battery voltage through the signal circuit to the transmission control module (TCM) and the engine control module (ECM) indicating that the brakes are applied.
Ground for the stop lamps is supplied as follows:
• G402 provides ground for the left rear stop/tail/turn signal lamps
• G403 provides ground for the right rear stop/tail/turn signal lamps
• G301 provides ground for the CHMSL
The stop lamps on this vehicle will not illuminate unless the ignition is in the accessory, run, or crank positions. When the ignition is in the OFF position the stop lamps will not illuminate when the brake pedal is applied.
Battery voltage from the LT TRN/SIG and RT TRN/SIG fuses located in the rear fuse block is also used by the body control module (BCM) for stop lamp operation.

Turn Signal Lamps
Battery voltage supplied to the body control module (BCM) from the fuses listed below is used for turn signal and hazard lamp operation.
• LT TRN/SIG fuse for the left turn signals
• CTSY/RF TRN fuse for the right front turn signal
• RR TRN/SIG fuse for the right rear turn signal
When the turn signal switch is place in either the LEFT or RIGHT position, ground from G300 is applied through the turn signal switch signal circuit to the BCM indicating the turn signal request. In response to this signal, the BCM applies a pulsating voltage to the front and rear turn signal lamps supply voltage circuits cycling the lamps ON and OFF. At the same time the BCM sends a GMLAN serial data message to the instrument panel cluster (IPC) to cycle the appropriate turn signal indicator ON and OFF.
Ground for the turn signal lamps is supplied as follows:
• G104 provides ground for the left and right front turn signal lamps
• G402 provides ground for the left rear stop/tail/turn signal lamps
• G403 provides ground for the right rear stop/tail/turn signal lamps

Do you have a factory scan tool (tech2) ? Your best bet , take it to the dealer .

Sep 08, 2017 | Buick Cars & Trucks

1 Answer

Where's the fuse for tail lights,fuse for dash light on a 2005 keep liberty located at?


now engine or country, they sell exports, not same.
car drives perfectly, must i ask?> and head lamps work.
finger drummming, ,,,,,,ugh!

all new jeeps that Park (its not tails now its park up to 3 or 4 per side of car, so is called park now)
circuits are shared, in many cases, other wise need 100 fuses.
now ill look at your SM , the missing service manual you skipped reading, (it may have a relay park too)
first ill pretend you said, USA
then said.KJ jeep
with 3..7 liter engine, sorry diesels can be quite different
ill pretend all side parks dead and inside, yes,they too are park related.
and license plate lamp DEAD
yes that park relay runs all outside lamps and fuse
JB7 and9
i guess dash lamp (so many ) is Cluster back lamps dead>
IP cluster? dead. for night driving,sure
fuse jb9 runs cluster.lamps
so but F7 runs right side.
so of left and right sides dead,
ill bet dollar to donuts, both are not blown'
so seems the really is toast or
BCM brains scramble,
Scan it yet, this is always first of 2fuse above are good.




only this (about)has one tail lamp. and tiny.1884
1884-dcdbp4hu0erzftuplknku2ok-4-0.jpg

Feb 24, 2017 | 2005 Jeep Liberty

1 Answer

I have a jeep liberty 2005 2 wheel drive my passenger side driving light will not come on. Also instrument panel lights will not come on either.


first off ,you did electric work and skipped step 1
pull battery neg lug first.
so you blew the fuses.
what IP lights. all warning lamps.
or just the park lamps in the cluster.
part is called Illumination in said cluster.

where is these other lights, what is a driving light, (park, head,turn, what? brakes?)
tell all lights that work & not , inside and outside car.
tell what knob you turn. can be like 10x better clue...?????
burned sockets are shorted lamps, the brass base lamps love to short inside, (china made x10) get new ones from top maker....

ok, so after replacing the TL assy.
what dont work now, report all lamps.
if it's only outside lamps failing, say so..
i guess you dont know that parking lamps go to like 20+ places, inside and outside car. so. parking lamps are special if acting up
then brake lamps
then blinkers (turn signals)
then reverse.

if the parks (aka, incorrectly TAIL) are bad, then we need to know that. using the correct word.
parks are on all 4 counters, and side lights and inside car.
that is why tail lamp , is a bad name. but fuses are marked as tail on many cars.

also when working on car external lighting
make sure no trailer towing hacks are found.
look for non OEM hack jobs, at the rear corners. Uhual hacks.
or past collision damage to wiring not repaired properly.

how is that>?

Jun 21, 2015 | 2005 Jeep Liberty Sport

1 Answer

2002 Jeep Libertys right side parking light and rear brake light won't go off.


kEy off?
wow both park and brake failures.
sounds like one is shorted to the other
and either park and brake are stuck.
ok take the the tests
key off, parks and headlights off,
look at all lamps on car inside and out, which are one.
is the dash lights glowing (called illumation lamps) on.
and side lights off, and front park lights off, ,yes, all off then park is off,
so of rear lights glow , is it just brakes, that means the brake lamp switch is stuck on.
elaborate please.

Dec 09, 2013 | 2002 Jeep Liberty

1 Answer

2003 Jeep liberty right front turn signal


why skip RR lamp? what does IT DO? be like 1st 1st look.
dim, out, fast?

the rapid is talking to you
it means current is wrong,
shorted, or open lines. to the right.
its the wiring
if the bulbs are like 1157 brass base bulbs
why not replace them first , they can short inside,
asking online for guessing is silly, why listen to 10 examples for this.
but is cut wires.
shorted wires.
keep i mind the blinker asks funny for both opens and shorts
its a feature, that.
low current or too much.

the acid test is connect 2 TEST bulbs in parallel to the multi-function switch output right side,
blinks ok now, bingo bad lamps or bad wiring, from there to the right side.

if the hazard fails you never said????
if rigth front is dim or dead the bulb is blown or shorted
if new bulb there , then the wires are shorted.
to it.
the only help on line worth squat is how to test and use your meter.
you can, check for voltage
you can check continuity on that line (its just 1 wire)
and check for shorts on that wire to ground (lamps pulled right side to do that, lamps read 0 ohms cold)
look for collision damage RF? behind lamp sockets?
be first.
in my book.
looking is always first. sure.


I have your SM book open now, chapter 8w-50
the haz/blink module has just 2 pins, left and right out.
pin 3 on the module runs front and rear blinks, (a fact to know)
RF is BR/RD, brown -red stripe?
all comments USA on USA forum. USA car.
ok?

the right side lamp (sidemaker) only blinks turns if parks ARE oFF

Id try 2 new blinker lamps front and 1 rear.
that be first. or test the lamp on a battery , and no not get burned fingers hot wring a shorted lamp.

wish i knew
what rear did
and what both did on HAZ
out, dim or to fast.

Mar 23, 2017 | 2003 Jeep Liberty

1 Answer

Right turn signal flashes fast and all rear and front


your tail light has no graund. usualy plastic conector no the lamp melt down around ground cable
marko

Aug 31, 2009 | 2000 Jeep Grand Cherokee

1 Answer

Neither turn signals work on jeep liberty 2006 sport


Signals are now controlled by a module on the right side of the steering column under the dash. Before doing anything yourself, bring it to the attention of the guys that did the rear...This problem can happen at any time but they may have disconnected a harness or ground while working, so give them a chance first to correct it.

Jun 18, 2009 | 2006 Jeep Liberty

2 Answers

1999 jeep grand cherokee - brake lights and turn signals working but Right tail light out with all other lights on--HELP??? My 1999 Grand Cherokee has no parking lights in the rear. The brake lights work...


I have taken my car to many shops to solve this problem. Long story short your tail light has a bad circut and entire lamp must be replaced. (Lamp cost approximate $130.00)

May 28, 2009 | 1999 Jeep Grand Cherokee

1 Answer

Right tail light went out.


I have had the same issue recently. I have a 2002 Gr Cherokee Ltd 4.7L. At first I thought it was the bulb, replaced the bulb to no avail. Then I thought maybe the bulb was rattled loose due to my subwoofer, but that still was not the case. After testing all my fuses I decided to test all of my lights. The hazards worked, back up lights came on, tail and brake lights were all working also but for some reason the blinkers will go out and the right rear brake light will not come on. It always comes back on for me though, so now I just use hand signals when it is temporarily not working. My only suggestion is a problem in the wiring.

Oct 13, 2008 | 2002 Jeep Grand Cherokee

1 Answer

Stuck in 4 wheel drive & pulls to the right??? jeep patriot 3.7 auto year 2002


They told me it is becouse the front tires are new and the back tires bad. I put new tires on the back the same as the front and hope this workes.

Jun 26, 2008 | 2002 Jeep Liberty

Not finding what you are looking for?
2002 Jeep Liberty Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

77201 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...