Question about 2006 Toyota Solara

1 Answer

Cont. top can you put the top up manuel if the motor for the top stops working

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 625 Answers

Yes it should be a way manufacturers also icludes this option
look at you owners manual or look behind the seats in the floor for a little hanlde
or call your dealer for an advise this is only is case you don't have the owners manual.

Posted on May 31, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Help with wiper motor


Check for voltage at motor connection. If voltage motor probably bad.

May 04, 2016 | Cars & Trucks

2 Answers

2004 Chevy Monte Carlo 3.4 the a/c stopped blowing,then it started overheating to the red within a couple miles,replaced the thermostat,the relay switch some days it overheats sometimes it runs fine


Are the cooling fans coming on ? What relay switch did you replace ?
The BCM will request low speed cooling fan operation from the PCM under the following conditions:
?€¢
Engine coolant temperature exceeds approximately 103?°C (217?°F).


?€¢
When A/C is requested and the ambient temperature is more than 10?°C (50?°F).


?€¢
A/C refrigerant pressure exceeds 1310 kPa (190 psi).


?€¢
After the vehicle is shut off if the engine coolant temperature at key-off is more than 117?°C (243?°F) and system voltage is more than 12 volts. The fans will stay on for approximately 3 minutes.


The engine cooling fan system consists of 2 electrical cooling fans and 3 fan relays. The relays are arranged in a series/parallel configuration that allows the PCM to operate both fans together at low or high speeds. The cooling fans and fan relays receive battery positive voltage from the engine wiring harness junction block. The ground path is provided at G101.
During low speed operation, the PCM supplies the ground path for the low speed fan relay through the low speed cooling fan relay control circuit. This energizes the FAN CONT #1 relay coil, closes the relay contacts, and supplies battery positive voltage from the FAN CONT #1 fuse through the cooling fan motor supply voltage circuit to the right cooling fan. The ground path for the right cooling fan is through the FAN CONT #2 relay and the left cooling fan. The result is a series circuit with both fans running at low speed.
During high speed operation the PCM supplies the ground path for the FAN CONT #1 relay through the low speed cooling fan relay control circuit. After a 3-second delay, the PCM supplies a ground path for the FAN CONT #2 relay and the FAN CONT #3 relay through the high speed cooling fan relay control circuit. This energizes the FAN CONT #2 relay coil, closes the relay contacts, and provides a ground path for the right cooling fan. At the same time the FAN CONT #3 relay coil is energized closing the relay contacts and provides battery positive voltage from the FAN CONT #2 fuse on the cooling fan motor supply voltage circuit to the left cooling fan. During high speed fan operation, both engine cooling fans have there own ground path. The result is a parallel circuit with both fans running at high speed.
Is your vehicles check engine light lit ?
Is the

Jul 10, 2015 | Cars & Trucks

1 Answer

Driver side wiper not working 1994 toyota camry


linkage there is only 1 motor.
but do look at it.
the arm is DEAD you mean. or it cont swipe cleanly> or what
what does not working mean.????

Jan 27, 2014 | Toyota Cars & Trucks

1 Answer

1996 saab 900s , cont. top didnt work at all, had "check latches" message. checked the system,pulled it apart and found the motor was installed incorrectly. had motor and position sensor...


You need to hook up the car to the factory tool, and check for codes. I think the lower limit for the main or 5th bow potentiometer needs to be adjusted. lots of service information at www.saabservices.com in the convertible top section

Mar 19, 2011 | 2001 Saab 9-3

2 Answers

Just not doing anything put new blower motor in and worked for one day then stopped working again no heat or air at all manuel trans 4cyclinder sl1 staurn car


Check for current at the blower motor using a test light to ground. If there isn't any, then the blower relay will have to be replaced, or check for a blown fuse.

Dec 18, 2010 | Saturn SL1 Cars & Trucks

2 Answers

2002 vw cabrio - top will not work


you need to make sure car is in park, parking break is on, and ALL windows are DOWN, then you should be able to put the top down. do the same thing to put the top back up too. hope this was helpful.

Mar 28, 2009 | 2002 Volkswagen Cabrio

1 Answer

Filling a manuel transmission


on the driver side of trans. there is 2 plug one above each other open the top one put oil in by the top
till it drip from the plug put plug back in, you are good to go

Mar 28, 2009 | 1996 Pontiac Sunfire

1 Answer

Manuel To Auto Tranny Swap, Will It Work?? Please Help!!


NOTE IF U DO SO U WILL HAFT TO CHANGE THE SHIFTERS DO NOT NO WHAT YOUR TRYING TO SAY BUT U NEED TO PUT WHAT EVER TR ANNY CAME WITH THAT MOTOR BACK TO THAT MOTOR ITS VERY BIG JOB

Feb 18, 2009 | 1990 Eagle Talon

1 Answer

Timing marks


This is a little hard, but you can do it the old fashoined way. You take the FIRST Spark plug out and stick a screw driver inside that hole. You crank the top gear until the little hash mark is all the way up. You will need two people to do the second step. the next thing you have to do is crank the bottom while using the screwdriver to make sure that the first cylinder is all the way up. Its very simple, but if it aint all the way up, your car wont start. You have to put the timing belt on those gears WITHOUT MOVING them AT ALL.

Nov 30, 2008 | 2005 Peugeot 405

1 Answer

Convertible Top Not Working Properly


This is not a low fluid problem, this a contorl motor problem. I had a 1989 Z24 conv. and the same thing happened. I replaced the motor and the top worked just fine.

Aug 26, 2008 | 1988 Chevrolet Cavalier Z24

Not finding what you are looking for?
2006 Toyota Solara Logo

Related Topics:

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

63990 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...