Question about 2003 Nissan Murano

Open Question

Getting a cam sensor position code (poo11, p0021) on my 03 Nissan Murano. Where are these sensors located ?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
ndguy2481
  • 251 Answers

SOURCE: location of cam positioning sensor for 1991 chev lumina 3.1

On your 1992 Chevrolet Lumina-Sedan/Coupe 3.1L MFI OHV , the Crankshaft Position Sensor is located: clearpixel.gif Under hood, passenger side, lower engine area, passenger side of engine block, mounted front of crankshaft pulley

Posted on Nov 30, 2008

Ad
  • 383 Answers

SOURCE: CANNOT FIND THE CRANKSHAFT POSITION SENSOR

cerebral_eni: The crank position sensor is located at the back of the engine block just below the cylinder head. It actually projects into the bell housing and reads the teeth on the flywheel where it references TDC for #1 cyl and RPM's of the crank. It's a "Hall effects generator". Unless you are into electronics and have a lab scope to look for a square wave pattern, I will continue with my other input.
Nissan has a recall campaign on the crank angle sensors.
The campaign # is 07V527000:ECM update for stalling;
NHTSA07V527000 NOV 07,
The symptom was brief malfunction of sensor causing the engine to quit running which could potentially put the vehicle at risk for a collision. The sensors would ultimately fail. There was also a voluntary recall on the reprogramming of the ECM's due to stalling problems. TSB# NTB07-081, Campaign ID#R0712
I hope this information is of some assistance to you. You may be able you get your car repaired under warranty! Good Luck!

Posted on Apr 08, 2009

SOURCE: WHERE IS THE CAM POSITION SENSOR LOCATED ON A 2004 NISSAN MAXIMA

WHEN YOU STAND ON THE FRONT OF THE CAR YOU ONE IS RIGHT BELOW OF THE INTAKE WHICH IS BANK 2 OR THE ONE CLOSE TO FIREWALL , BANK 1 ONE IS ON SAME SIDE NEXT TO THE RADIATOR BUT THEY BOTH ON THE CAM RIGHT SIDE OF THE ENGINE, THE EASIEST WAY TO IDENTIFY THEM IS THAT THEIR CONNECTOR IS GREEN, ONCE YOU LOCATE THEM THE CLIP NEEDS TO BE PUSHED DOWN TOWARD THE SENSOR FOR THE CONNECTOR TO BE RELEASED, ONCE YOU REMOVE THE CONNECTOR THERE WILL BE ONLY A 10MM SCREW HOLDING THE SENSOR PULL IT OUT , THE SAME SETTING THE NEW ONE PUSH IT ALL THE WAY IN , THIGHT THE 10MM SCREW, CONNECT IT BACK AND YOU'RE DONE,BUT FOR THE ONE ON THE BACK SOMETIMES MIGHT BE NECESARY FOR YOU TO TAKE THE INTAKE OFF....HOPEFULLY IS NOT YOUR CASE....



Good luck!!! and if you need the crank for hard starting on hot/warm, it is located on the botton middle section on the transmission is the only cable that goes down to a small piece of metal and it is held by a 10mm screw only to protect the sensor, you will se the sensor once you remove that small about 6-8 inches piece of metal. Then you'll be able to unescrew the 10mm screw that holds the crank position sensor. when you pull it off you'll be able to see the fly wheel inside the transmission...



you all enjoy your rides out htere!!!

Posted on Jul 01, 2009

  • 145 Answers

SOURCE: where is the cam position sensor located on a 2004

Here is 7353049.jpg

Posted on Jul 02, 2009

duane_wong
  • 6826 Answers

SOURCE: I need to find the camshaft position sensor on my

Camshaft Position Sensors are located on the cylinder head according to the following: Camshaft, Bearings & Lifters Removal & Installation To Remove:

  1. Remove the engine from the vehicle.
  2. Remove the front suspension member, transaxle and transfer case (if equipped) from the engine.
  3. Mount the engine in a suitable engine stand.
  4. Remove the timing chains and rear timing chain case.
  5. Remove the camshaft position sensors from the cylinder heads.
  6. Remove the intake valve timing control solenoid valves. NOTE: Mark the camshafts, camshaft brackets, and bolts so they are placed in the original locations during installation.
  7. Loosen the camshaft bracket bolts in several steps using the order shown.
  8. Remove the intake and exhaust camshaft brackets and the camshafts. Camshaft bracket bolt removal sequence nissan-03-35-4624.gif

  9. Remove the valve lifters and the secondary timing chain tensioner with stopper pin attached if necessary.
NOTE: Stopper pin was installed when the secondary timing chain was removed.
To Install:
NOTE: Clean sealant from front camshaft bracket, bolts and bolt holes.
  1. Turn the crankshaft until No.1 piston is at TDC on the compression stroke. The crankshaft key should line up with the right bank center line as shown. Crankshaft keyway position nissan-03-35-4625.gif

  2. If removed, install the secondary timing chain tensioners and valve lifters in their original positions. NOTE: The intake camshaft has a drill mark on the edge of the sprocket mounting flange.
  3. Position the camshafts on the cylinder heads with the dowel pins as shown. Camshaft dowel pin positions nissan-03-35-4626.gif

  4. Apply silicone sealant to the front (No. 1) camshaft bracket as shown. Apply silicone sealant to the front (No. 1) camshaft bracket nissan-03-35-4627.gif

    Camshaft bracket bolt installation sequence nissan-03-35-4628.gif

  5. Install and tighten the camshaft brackets using the following steps in the sequence shown;
    • Step 1 (bolts 7 - 10) : 1 ft-lb (2 Nm)
    • Step 2 (bolts 1 - 6) : 1 ft-lb (2 Nm)
    • Step 3 (bolts 1 - 10): 4 ft-lbs (5.9 Nm)
    • Step 4 (bolts 1 - 6) : 8 ft-lbs (10.4 Nm)
    • Step 4 (bolts 7 - 10) : 7 ft-lbs (9.3 Nm)
  6. Wipe off excess sealant from bracket No. 1.
  7. Measure the difference between the front surfaces of camshaft bracket No. 1 and the cylinder head. The specification is -0.0055 to 0.0055 in (-0.14 to 0.14 mm). Replace the camshaft and camshaft bracket if out of specification. Measure the difference between the front surfaces of camshaft bracket No. 1 and the cylinder head nissan-03-35-4629.gif

  8. Install the IVT control solenoid valves with new gaskets.
  9. If removed, install the camshaft position sensor.
  10. Install the rear timing chain case and timing chains.
  11. Install the engine in the vehicle.
prev.gif next.gif

Posted on Jul 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a nissan murano 2005 with the code p1701 and a p0340 how can i use them to repair these codes


Nissan Murano P0340 2005 Nissan Murano - Camshaft Position Sensor Circuit
Possible causes- Faulty Camshaft Position Sensor-
Camshaft Position Sensor harness is open or shorted- Camshaft Position Sensor circuit poor electrical connection- Faulty starter motor- Starting system circuit-
Dead (Weak) battery
P1701- Fuel trim

I would suggest replacing the camshaft position sensor. When the sensor fails it can cause changes in fuel system that the computer can detect. So I suspect once the camshaft sensor ivreplaced that the P1701 code will be gone.
Cam Position Sensor Replacement Nissan Murano 3 5L

Sep 20, 2015 | Nissan Cars & Trucks

1 Answer

Murano Cam Sensor


rear of front cylender head below fuel presure regulator

Jul 02, 2013 | Cars & Trucks

1 Answer

What is P0011 code


Hi there:
DTC P0011 is a code for a Camshaft Position sensor failure.


I would start with the cam sensor, then crank sensor, and clear the codes, see how it behaves on a test drive.


The cam position sensor is easier to replace than the crank sensor, you may want to start with that alone. There's two cam sensors on the V6, your code indicates the Bank 1 sensor is causing trouble, that's the cylinder head closest to the firewall.



The crank position sensor is on the engine block also on the firewall side, tucked up next to the starter, and somewhat hard to reach, especially without a lift.



Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Oct 11, 2012 | 2006 Nissan Murano

1 Answer

Nissan altima 3.5l v6 2005 poo11


code 11 is camshaft position sensor bank 1 circuit malfunction.

Nov 15, 2011 | Cars & Trucks

1 Answer

I have nissan murano,and it has an error on (VTC P0021),what should I do?


Possible Cause:
Crankshaft position sensor
Camshaft position sensor
Accumulation of debris to the signal pick-up portion of the camshaft.

Aug 09, 2011 | 2003 Nissan Murano

1 Answer

My Nissan Murano 2004 is getting trouble code p1273


that is a code for the A/F sensor. that is a air/fuel ratio sensor aka front 02 sensor. used to be called front 02 sensor, but nowadays they call them A/F sensor.

Apr 19, 2011 | 2004 Nissan Murano

1 Answer

Nissan murano 2004 i need to solve this problem p0340


Hope this helps, it it does please leave feedback and vote Thank You and Good Luck


Component Inspection

CAMSHAFT POSITION SENSOR (PHASE)
  1. Loosen the fixing bolt of the sensor.
  2. Disconnect camshaft position sensor (PHASE) harness connector.
  3. Remove the sensor.
108947220

  1. Visually check the sensor for chipping.
108947221
108947222

  1. Check resistance as shown.

Jan 02, 2011 | 2004 Nissan Murano

1 Answer

NISSAN MURANO 2004 I receive an error on my screen Check Engine & after checking at the garage the problem was P0340 what would it be ?? & how to fix ?? when running on the highway the engine...


the P0340 is a camshaft sensor code, the sensor is located in the front (passengers ) side of the engine, there should be two sensor's one for each camshaft, (front of each head) defective cam sensor's can cause the the problems of stalling and hard starting. I am a Nissan certified tech and replaced a good number of cam sensors in the past, they are quit easy to replace, they are attached by one ten millimeter headed bolt (per sensor) remove the bolt then work the sensor clockwise and counter clockwise while pulling out, there is a o ring seal on the sensor and when installing the new one lightly lube o ring before installing, then install sensor and be sure it fully seated against the mounting surface before installing the bolt or you will break the mounting ear of your new sensor. thanks for using fixya

Jan 01, 2011 | 2004 Nissan Murano

1 Answer

Wereplaced head gasket on a 2002 nissan altima and now a have a poo11 code . i have rechecked timing and cleaned v v t


TROUBLESHOOTING P0011
The pcm has determined that the voltage signal from camshaft "A" position sensor in bank 1 indicates inadequate perforemce or a timing over advanced condition. (Bank 1 identifies the location of cylinder #1, while bank 2 identifies the cylinders on the opposite bank)

hopefully this helps a little

Dec 02, 2010 | 2003 Nissan Altima

1 Answer

Where is the crankshaft position sensor for a 2007 Nissan murano?


CRANKSHAFT SENSOR LOCATED ON THE OIL PAN FACING THE GEAR TEETH COGS OF THE SIGNAL PLATE.

Oct 16, 2010 | 2007 Nissan Murano SE

Not finding what you are looking for?
2003 Nissan Murano Logo

Related Topics:

476 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...