Question about 1989 Dodge D150

1 Answer

Cleaned engine, replaced distributor, cap, rotor button, plugs, and plug wires. Now, engine will not fire. It turns over, but never cranks. Tested, with a volt tester, the coil and there was no voltage from the coil. Also, do not think there is any gas getting to the engine. I have listened for the fuel pump to come on in the gas tank byt turning the key on, and it sounds like it is coming on.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 8,128 Answers

Check ECM for water--unhook connector, dry as necessary. ECM is driver side, front side of wheelwell, mounted on inner fender. Your ECM powers injectors and coil. Might want to check ignition fues in battery fuse box too.

Posted on Oct 11, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1990 geo storm sohc is running rough. Parts that are new: cap, rotor, plugs wires,plugs, pickup coil, and the ignition module looks brand new. The coil is old, but is still sending spark through all t


the timing is 180 degrees out so ignore where no 1 lead should be and rewire the HT leads to the new position for no1 cylinder. The crank timing mark should be on 10 degrees advanced. Engines are timed off the crank position so forget the cam position.
Or you can start again. Remove no 1 plug and turn the engine over until you feel compression under your finger over the plug hole. Set the timing on the crank to 10 degrees before tdc. Position the distributor so that the point of the star is directly opposite the exciter coil in the distributor. The rotor button should now be facing no 1 cylinder plug lead adjust the HT leads so that they will fire in the 1342 firing order. Start the engine and with a timing light attached to no 1 plug lead adjust the timing mark to specifications by turning the body of the distributor.

Nov 06, 2014 | 1990 Geo Storm

1 Answer

1988 ford bronco11 have feul,but no fire from distributor to coil


with distributer cap off have someone crank engine and see if your rotor is turning if not repair distributer or replace.

Apr 05, 2014 | 1988 Ford Bronco II

1 Answer

I replaced cap rotar and dist. now it cranks over but will not fire and is back firing


the timing is off a bit! heres how I do it. remove the number 1 plug, stick a straw or similar in plug hole. turn engine over by the crank shaft with a wrench. when piston gets to very top of bore, just before it goes down. this is tdc. remove distributor cap and remove distributor reposition the distributor rotor button facing number 1 plug wire inside cap. replace cap and try it! please let me know if this works for you. good-day ! if you can not get to number 1 plug. just turn the crank to tdc marks are on damper pully or crank. is this a 5.7,

Apr 08, 2012 | 1997 GMC Yukon

1 Answer

Spark plugs and wires


It sounds like the spark plug wires are not plugged into the correct place on the distrubutor. take the distributor cap off and crank the engine over. Make a note of which direction the rotor spins. (Clockwise, or Counterclockwise) then find the firing order for that engine. Sometimes the firing order is on the intake manifold. (if you tell me which engine it has, the 4 cylinder 2.0, or the 6 cylinder 2.5; I could post you the firing order). Now on the distributor cap there is one wire post that has the #1 on it, that would be where you put the spark plug wire from cylinder 1. Following the rotation of the distributor rotor, you would put the spark plug wire for the next cylinder in the firing order after the #1 wire, and so on.

Dec 11, 2011 | 1998 Ford Contour

5 Answers

Truck wont crank. we have put new distributor cap, rotor button, coil pack, plugs, wires, and fuel pump. we also checked our firing order.


you said you repl dist cap that means you don't have a crank sensor you have electronic ing module. remove your elec ing module have it tested most auto parts stores could test your module, or check your coil at the neg terminal. should have power. if not you lost your primary volt from your batt.your secondary power is coming from your electronic ing module from the module to the pos terminal on the coil, when the eng cranks,from the coil to the dist cap , from the dist cap center to the rotor then out to the plugs,this all happen pervided the timing belt or timing chain is ok. the cumbustion chainber needs 3 things , thats fuel, air, and spark.

Apr 17, 2011 | 1996 Chevrolet K1500

1 Answer

My engine turns but no spark I changed ignition coil and still no spark,what could it be?


Depending on which engine your car is equipped with; the following components could be at fault.

Crankshaft Position Sensor
Camshaft Position Sensor
ECM (Engine Control Module)
Distributor Cap or Rotor
Fouled Spark Plugs
Bad Plug Wires

If they haven't been replaced in the last 30K miles, I suggest you check and /or replace the the plugs and wires first.

If your engine is equipped with a distributor, check and/or replace the distributor cap and rotor if it hasn't been replaced in the last 30k miles.

If your engine is equipped with crank or cam sensors have them tested.

Mar 21, 2011 | 1990 Volkswagen Cabriolet

2 Answers

Need to know the plug wiring distributo to plugs


take distributor cap off turn engine over so u can work out which way the rotor arm spins.then turn engine over manually till u lign up timing mark on crank pulley roto shld now point to number 1.firing order is 1 3 4 2 making sure u do this cobination the way the rotor turns when engine is tiurning over

Apr 14, 2010 | 1996 BMW 318

1 Answer

95 dodge caravan with no start problem.


Connect a timing light to the number one plug wire and crank the engine. Does the light flash indicating that the Number one is firing? Look at the distributor. If you have a distributor cap and rotor assembly remove the distributor cap and crank the engine. If the rotor turns check the rotor to make sure there is a good contact point and check the distributor cap to ensure there are good contacts. If either is damaged or worn replace them both. If the rotor does not turn you have a broken timing belt or one of the timing belt/chain guides has jammed and the engine needs to be rebuilt.

Sep 08, 2009 | 1995 Dodge Caravan

2 Answers

97 Nissan 200sx cranks, won't turn over


If you indeed are getting no spark on any plugs, check your plug wire that runs from the rotor to your ignition coil- the one that doesn't go to the engine. Make sure the internal connections didn't pull out and get crushed back in or fall out. Try one of your other plug wires on it and see if it fires- won't run good but you will see difference and be done troubleshooting. Other than that, you bought the rotor button and and rotor as a set right? Make sure the button metal tip is contacting the cap. If you got the wrong one, it may sit too low for the contacts even if it is long enuff. If you were getting spark, I would just say you got the firing order wrong.

May 13, 2009 | 1997 Nissan 200SX

Not finding what you are looking for?
Cars & Trucks Logo

197 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...