2001 Audi TT Logo

Related Topics:

Posted on Oct 11, 2010
Be the first to answer

Location of windshield washer reservoir, 2000 TT

Answer This Question

5 Related Answers

Anonymous

  • 2 Answers
  • Posted on Nov 23, 2008

SOURCE: windshield washer reservoir tank is leaking how do I replace?

You must remove from it's mount and empty out any fluids that is in tank.fill the tank with water and locate where the leak is coming from. wash tank a few times and the let dry upside down. Get some sand paper (80  grit course) and sand area where leak is, clean area with a vacume or clean rag.you can buy a 2 stage epoxy that comes in an injection form and squeeze it out on a pc of paper and then get a q-tip and mix the 2 components together, fill the crack or hole generously with the q-tip, if you have to,let dry for 24 hours and mix more and put more on. let dry another 24 hours, replace tank back in it's place and you've solved your leak. (epoxy does wonders if its used properly.
Frankthetank

Ad

Anonymous

  • 5 Answers
  • Posted on Nov 27, 2008

SOURCE: Windshield washer fluid will not pump

the windshield washer pump might be bad. It should be located somewhere on the reservoir

Anonymous

  • 11896 Answers
  • Posted on Jun 23, 2009

SOURCE: windshield washer fluid reservoir - MB ML 350

right where the lines connect to reservoir, has little black seals that leak. I recommend removing reservoir, empty it out, then use RTV silicone and place it between seals and reservoir. Let it dry for FULL day. than reinstall.

Anonymous

  • 166 Answers
  • Posted on Aug 21, 2009

SOURCE: Replace 2001 silverado 1500 4x4 windshield washer fluid reservoir

the only solution acording to the manual is to replace the reservoir... not much to say about that, u do have the option to patch it...be careful with the product u use to glue that patch.
take care

Anonymous

  • 1 Answer
  • Posted on Jan 07, 2010

SOURCE: no washer fluid coming out of windshield washer.

I have the same problem. But I can not actually hear the pump working to spray the liquid. I'm not actually sure if I ever did when it was working. Is there a fuse for this? I looked in the manual, and I don't see it.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1helpful
1answer

2000 expedition Windshield washer fluid reservoir
Call your local parts store and see if they have the same part number.
Read full answer
Oct 15, 2022 • Ford Cars & Trucks
0helpful
1answer

2000 mercury villager windshield washer reservoir low-level light
Replace the probe and check grounds
Read full answer
Feb 16, 2014 • Cars & Trucks
0helpful
1answer

Cannot fiend windshield washer motor
the motor is usually in the washer fluid reservoir. follow the hoses from your windshield nozzles back towards your reservoir and if it is external pump, you will run right into it
Read full answer
Mar 16, 2013 • Cars & Trucks
1helpful
1answer

2002 chrysler concorde evap cannister location
look engine compartment near cruise control actuator or look fender panel near windshield washer fluid reservoir.chrysler put EVAP CANISTER DIFFERENT PLACES.
Read full answer
Dec 15, 2012 • 2000 Chrysler Concorde
0helpful
1answer

Replace windshield reservoir
Windshield Washer Motor REMOVAL & INSTALLATION 1987-95 Vehicles
  1. Disconnect the negative battery cable.
  2. Drain or siphon the washer solvent from the reservoir.
  3. For 1987-91 vehicles, remove the brace.
  4. Unfasten the reservoir screws.
  5. Detach the electrical connectors and washer hose.
  6. If necessary, remove the reservoir from the vehicle.
  7. Remove the washer pump motor from the reservoir. Fig. 1: Location of the windshield washer fluid reservoir and pump - 1987-91 vehicles 89636g50.gif
    To install:
  8. Install the washer pump motor on the reservoir. Make sure the pump is fully seated in the reservoir gasket.
  9. Position the reservoir in the vehicle.
  10. Attach the electrical connectors and washer hose.
  11. Install the reservoir retaining screws.
  12. Install the brace.
  13. Fill the reservoir with washer solvent.
  14. Connect the negative battery cable, then check for proper washer pump operation.
1996-99 Vehicles
  1. Disconnect the negative battery cable.
  2. Drain or siphon the washer solvent from the reservoir.
  3. Detach the electrical connectors from the washer.
  4. Disconnect the hose from the washer pump.
  5. Loosen the nut at the bottom of the washer reservoir.
  6. Unfasten the 2 nuts, then remove the washer solvent reservoir.
  7. Remove the washer pump from the container.
  8. If necessary, remove the solvent lever sensor switch from the washer solvent container. Fig. 2: Exploded view of the washer fluid reservoir, pump and level sensor 89636g51.gif
    To install:
  9. Install the solvent level sensor switch in the washer solvent container. The tab on the solvent level sender switch must be lined up with the slot in the hole.
  10. Install the washer pump into the reservoir, making sure the pump is pushed all the way into the container seal.
  11. Install the washer solvent reservoir and secure with the 3 nuts. Tighten the nuts to 44 inch lbs. (5 Nm).
  12. Attach the electrical connectors to the solvent level sensor and washer pump.
  13. Connect the hose to the washer pump.
  14. Fill the reservoir with washer solvent.
  15. Connect the negative battery cable, then check for proper washer pump operation.
prev.gif next.gif
Read full answer
Nov 09, 2010 • 1997 Pontiac Bonneville
4helpful
2answers

How do I fix my window washer pump on my 2000 dodge caravan?
One can get a repair kit that includes a new motor pump and wiring clips, or

one can get the original motor that plugs into the windshield wiper fluid reservoir.

---
Windshield wiper reservoir (gives idea of how to change the windshield wiper fluid pump motor) Removal & Installation To Remove:
  1. Disconnect and isolate the negative battery cable.
  2. Raise and safely support the vehicle.
  3. Remove the right front wheel and splash shield.
  4. Disconnect the electrical connectors from the pumps and detach the rear washer hose.
  5. Place a drain pan under the reservoir if it contains fluid.
  6. Disconnect the front washer hose at the wiper unit in the engine compartment. NOTE: The front hose will be removed with the reservoir.
  7. Let the fluid drain from the reservoir.
  8. Remove the mounting screws and the reservoir.
To Install:
  1. Install the fluid reservoir with the mounting screws.
  2. Connect the front washer hose in the engine compartment.
  3. Connect the electrical connectors and rear washer hose.
  4. Install the splash shield.
  5. Install the right front wheel.
  6. Lower the vehicle.
prev.gif next.gif
Read full answer
Aug 27, 2010 • 2000 Dodge Caravan
2helpful
1answer

Mercury villager 1994 washer pump not working
the pump motor likely is bad. get a used washer fluid reservoir at a pick n pull yourself or at car-part.com. page with * is lowest cost.

Pump and Reservoir, Windshield Washer Removal
  1. Disconnect the battery ground cable (14301).
  2. Raise and support the vehicle.
  3. Remove the RH wheel (1007).
  4. Remove the RH front fender splash shield (16103). Refer to Section 01-02 for the removal procedure.
  5. Remove the windshield washer reservoir top bolt.

  6. Disconnect the windshield washer reservoir fluid level sensor electrical connector.
  7. Disconnect the rear window washer pump electrical connector from the rear window washer pump.
  8. Disconnect the windshield washer pump electrical connector from the windshield washer pump (17664).
  9. Place a suitable drain pan under the windshield washer reservoir (17618) and drain the washer fluid.
  10. NOTE: The rear window washer hose end is color-coded, matching the connector on the rear window washer pump. Match the colors to ensure proper installation.

    Disconnect the washer hoses from the windshield washer pump and the rear window washer pump on the windshield washer reservoir.

  11. Loosen the two windshield washer reservoir side bolts.
  12. Remove the windshield washer reservoir by sliding it out of the side slots.
  13. Remove the windshield washer pump.

    Installation
To install, reverse the removal procedure. Tighten the lug nuts (1012) to 98-118 Nm (72-87 lb-ft).
Read full answer
Sep 09, 2009 • 1994 Mercury Villager
2helpful
1answer

Wash wipe on a Focus 2000 model
I blieve it's the same pump taht runs the rear and front washers.

The windshield washer comprises the following parts:
  • Windshield washer reservoir, below the front left-hand fender
  • Washer pump, on the outside of the washer reservoir
  • Two washer nozzles on the hood/bonnet, adjustable.
---------------------------------------------------------
Windshield Washer Pump and Reservoir Removal
All vehicles
  1. Remove the windshield washer reservoir filler neck.
  1. Raise and support the vehicle. For additional information, refer to Section 100-02 .
  1. Remove the right-hand fender splash shield (wheel shown removed for clarity).
  1. Remove the washer reservoir.
    • Disconnect the electrical connectors.
    • Pull off the hoses.
  1. Remove the windshield washer pump with rubber gasket (shown with reservoir installed).
    1. Disconnect the electrical connector.
    1. Disconnect the hoses.
    1. Lift out the pump.
Read full answer
Feb 27, 2009 • 2000 Ford Focus
0helpful
2answers

Wiper fluid level sensor replacement
Reservoir —Windshield Wiper

Removal
  1. Remove the RH wheel; refer to Section 204-04 .
  1. Position RH splash shield aside.
    1. Remove six screws.
    1. Remove three pin-type retainers.
    1. Position RH splash shield aside.
  1. NOTE: Windshield washer fluid should be collected in a container after the windshield washer hoses are disconnected.
    Disconnect the electrical connector and washer hoses.
  1. Remove the upper reservoir bolt.
  1. Remove the windshield washer reservoir.
    • Loosen the two lower reservoir bolts.
------------------------------------------------------------------------------------

Read full answer
Jan 15, 2009 • 2000 Mercury Villager
3helpful
1answer

Winshield washer motor does not run
These days, most windshield washer pumps are mounted to the bottom of the washer fluid reservoir. Where’s that, you ask? Well, inner+fender+w+text.jpgyou know that spout you pour the fluid into—the one that disappears into nowhere? Well, the reservoir is actually 2384f71.jpglocated inside the front fender between the bumper and the front wheel. To replace the pump, you will have to jack up the vehicle, remove the front wheel and then remove the inner fender liner.
Read full answer
Jun 08, 2008 • 2001 Honda Civic
Not finding what you are looking for?

View Most Popular

2001 TT

  • Cars & Trucks

Related Question

2000 expedition Windshield washer fluid reservoir

  • Ford Cars & Trucks

Related Topics

284 views

Ask a Question

Usually answered in minutes!

Popular Questions

I have white smoke coming from radiator - minus temp outside - no warning lights on - no smell - Audi TT

2002 Audi TT

2008 TT Convertible Top Issues

2008 Audi TT Coupe

Boost(?) problem audi tt

2004 Audi TT

Air bag warning light stays on

2000 Audi TT

My gas cap and trunk wont open. I need gas.

2002 Audi TT

Check Out the Latest Top Trucks Report!
Check Out the Latest Top Trucks Report!

View all Fixya Reports

Top Audi Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...