Question about 2000 Chrysler Cirrus

1 Answer

Spark plu wires connected incorrectly to distributor cap of 2000 chrysler cirrus

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chrysler Master
  • 8,266 Answers

Is yours one of these?

spark plu wires connected incorrectly to - 2338533.gif

2cd1561.gif

Posted on Oct 11, 2010

Testimonial: "The top diagram is correct...but think my wires are placed wrong gonna check em...thanx for your input"

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you replace thr distributor on a 1998 cirrus


For the 2.5L v6 engine:

Disconnect the negative battery cable. There is a remote negative connection at the left strut tower with an insulator grommet. Place this grommet on the stud to prevent the negative cable from accidentally grounding.
Remove the following: the bolt attaching the air inlet resonator to the intake manifold. Loosen the clamps holding the air cleaner cover to the air cleaner housing. Remove the PCV air hose from the air inlet tube. Loosen the hose clamp at the throttle body.
Remove the air cleaner cover, resonator, and inlet tube. Remove the EGR tube.
Mark for identification and remove the spark plug wires from the distributor cap.
Remove the distributor cap-there are two hold down screws. Mark the rotor position relative to the distributor body. Then remove the rotor.
Unfasten the two electrical connections from the distributor.
Remove the two distributor hold-down nuts and washers. If necessary, remove the spark plug cable mounting bracket.
Remove the transaxle dipstick tube. Then remove the distributor from the engine.
To install: Inspect the distributor's O-ring seal and replace if necessary Carefully engage the distributor drive with the slotted end of the camshaft. Verify rotor alignment with the previously made mark. Reinstall the hold-down nuts and washers and tighten to 9 ft. lbs. Connect everything back in reverse order.

If timing was disturbed while distributor was out: rotate the crankshaft until the #1 piston is at TDC of the compression stroke. Rotate the rotor to the #1 terminal position on the distributor cap. Put the distributor in place, engaging the distributor drive with the drive on the camshaft. With distributor seated, the rotor should be on the #1 terminal. Reinstall the hold-down nuts and washers.

Well, that's all! So much stuff is in the way, it makes it difficult. Post back if you need more help. Good luck.

Jun 16, 2014 | 1998 Chrysler Cirrus

1 Answer

Where is the distributor cap in my 2000 chrysler cirrus 2.5l V6


On the rear face of the right cylinder head. Cam sensor is built into it too. Just follow a plug wire.

May 03, 2012 | 2000 Chrysler Cirrus

1 Answer

Don't know which order spark plug wires go in to the distributor


V6? the cap should be marked. front cylinders are 2 4 6 rears are 1 3 5. the firing order is 1 2 3 4 5 6.

Sep 08, 2011 | 2000 Chrysler Cirrus

1 Answer

Spark plug to distributor cap Wiring schematic for a 96 Chrysler cirrus


I'm guessing that you have the 6 cyl 2.5 liter engine because the 2.4 liter engine that the Cirrus had for that year I believe had a coil pack. The picture below is for the 2.5. If you need the other just write a reply and I will be notified in my email and I will post it if needed. I hope this helps you and good luck.


clifford224_148.jpg

Mar 18, 2011 | 1996 Chrysler Cirrus

2 Answers

I wanted to know where the distributor is located on my 2000 chrysler cirrus


It doesn't have a distributor. It has a distributorless ignition system.

Jan 19, 2011 | Chrysler Cirrus Cars & Trucks

1 Answer

Car will not start. Replaced plugs, wires, distributor cap, and rotor. Still has no spark.


Check your ignition module. Are you getting power to the distributor?

Sep 20, 2010 | 1996 Chrysler Cirrus

1 Answer

I have a 2000 Chrysler Cirrus. When it rains,


Check Battery, all battery connections, the ground from motor to frame and from battery to motor and or body. A poor ground connection can cause all kinds of problems. Also i had a car that would not start in high humidity that turnedout to be the starter. It was pulling too much juice from the battery at high humidity.

Jul 26, 2010 | 2000 Chrysler Cirrus

1 Answer

New fuel pump and still wont start


1 Inspect Battery Battery Discharged or Faulty. 2 Inspect Battery Cable Corroded, Broken, Shorted or Poorly Connected Battery Cable. 3 Inspect Distributor Cap Distributor Cap Cracked or Burned. 3 Inspect Fuel Filter Clogged or Dirty Fuel Filter. 5 Inspect Coil - Ignition Faulty Ignition Coil. 6 Inspect Wireset Worn, Damaged or Faulty Spark Plug Wire(s). 7 Inspect Spark Plug Incorrectly Gapped or Fouled Spark Plug(s). 8 Inspect Starter Starter Motor Faulty. 9 Inspect Fuel Pump Low Fuel Pressure. 10 Inspect Solenoid Switch Faulty Starter Solenoid Switch. 11 Inspect Relay - Fuel Pumpat Faulty Fuel Pump Relay. 12 Inspect Fuel Injector Pressure Regulator Faulty Fuel Injector Pressure Regulator. 13 Inspect Ignition Switch Improperly Connected or Faulty Ignition Switch. 14 Inspect Starter Drive Faulty Starter Drive. 15 Inspect Fuel Injector Dirty or Worn Fuel Injectors. 16 Inspect Fuel Pump Strainer Clogged or Dirty Fuel Pump Strainerat. 17 Inspect Engine Control Computer Incorrect Operating Information Being Delivered and Sent From The EEC. 18 Inspect Fuel Tank Fuel Tank Empty. 19 Inspect Carburetor Carburetor Flooded or Faulty Choke. 20 Inspect Distributor Worn, Loose, or Incorrectly Installed Distributor.

May 22, 2010 | 2000 Dodge Caravan

1 Answer

1995 chrysler cirrus 2.5 has no spark


ITS NOT READING BECAUSE IT IS OBD 1 FIND A SHOP WITH A GENESIS COMPUTER THAT CAN READ OBD 1 AND 2

Jul 29, 2009 | 1995 Chrysler Cirrus

Not finding what you are looking for?
2000 Chrysler Cirrus Logo

Related Topics:

133 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...