Question about 1992 Jeep Wrangler

Open Question

1992 jeep wrangler ignition switch replacement

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: 1992 Jeep Wrangler heater not blowing hot air

How often has the coolant been changed? My only guess is that it hasn't and the hoses and the heater core are plugged up with goo and a flush is needed

Posted on Dec 26, 2008

  • 6982 Answers

SOURCE: 1988 Wrangler Ignition Switch Removal

There are four (sometimes two) bolts that hold the steering column to the dash. remove them & column will come down to let you get in there.
follow instruction sheet with switch. if you don't get it centered correctly it wont work correctly.

Posted on Jan 05, 2009

smokenic
  • 49 Answers

SOURCE: Dont know were to put in new transmission oil on a 1992 Jeep Wrangler

It's on the passenger side of your transmission, around half way down. after draining your fluid, fill untill fluid comes out where your putting it in

Posted on Sep 12, 2009

  • 6982 Answers

SOURCE: 2006 Jeep Wrangler won't start

First, make sure you can turn the engine by hand. If you can't then the starter can't turn it either. Have someone else turn the key and look for the source of the click...may be a relay. Go over the starting circuit with a volt meter. Check for power at the starter main terminal and then with the key turned to "start" check for power at the trigger terminal on the starter. Check battery voltage and check relay operation.
You have a neutral safety switch on the transmission if its an automatic and a clutch switch if it's a stick. Check them as well. Make sure battery grounding on fender and block are also clean and secure.

Posted on Oct 02, 2009

Testimonial: "Will try! Thanks!"

saailer
  • 1868 Answers

SOURCE: ignition switch 1992 Lebaron

Hello! Disconnect +battery cable...Remove tilt lever...Remove 3 Torx column cover attaching screws...Then the upper and lower column column covers...Using a Torx with a security tip (also called tamper proof tip) #440-tx20H... Remove 3 ignition switch mounting screws...Carefully pull switch away from column...Release 2 connector locks on 7 terminal wiring connector...Then disconnect from ignition switch...Release connection lock on 4 terminal connector...Then disconnect from ignition switch.

Guru..................saailer

Posted on Jan 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I install a replacement ignition switch in a 1995jeep wrangler Rio Grande


Chrysler Jeep Ignition Switch LS711 LS922 Replacement by Wells EM: https://youtu.be/reonxApWkVU

Here's a short video i found on you tube hope it helps you

Mar 07, 2015 | 1995 Jeep Wrangler

1 Answer

I am not gettin spark in my 1992 jeep wrangler i found a plug tht is not plugged in but i cannot find out where it goes any ideas??


Regarding your no spark condition....if your check engine light does not light up on the dash when you turn on the ignition, before cranking, then your jeep ecu might be in need of repair.

Jul 18, 2011 | 1992 Jeep Wrangler

1 Answer

I am hoping that some of you jeep brainiacs out there can help with a suggestion of the problem with my 1992 Jeep Wrangler 4.0 hi-output. Symptoms: backfire from time to time....cuts off when driving, cuts...


I remember the "Parts Replace" routine all too well from my truck. It's probably the fuel filter needing to be changed, clogging up and clogging the flow.

Dec 19, 2010 | 2003 Jeep Wrangler

1 Answer

For 1992 Wrangler, manual transmission, able to jumper across the hot and start connections on the solenoid to start the truck, but nothing when the key is turned.


The problem is in your ignition switch. The ignition switch is in the steering column. It is just inside or under the dash. The ignition switch is not sending power to the starter solenoid.

Oct 02, 2010 | 1992 Jeep Wrangler

1 Answer

1992 Wrangler: engine maintaince light comes on for 3 seconds the...


that is the engine management system checking itself,thats what its supposed to do.

May 17, 2010 | 1992 Jeep Wrangler

1 Answer

My jeep dosent want to start. It doesn't crank when i try to start it. i replaced the starter and the battery. what can it be


check the neutral safety switch and the starter relay. Also check ignition switch to make sure power is going in and coming out to starter. If automatic the neutral switch is on the passenger side of the trans, if stick you have a clutch switch on the pedal. relay is in the power distribution center near the battery, ignition switch is above the column under the dash. Try to turn the engine by hand to make sure it hasn't seized. Check power and grounding with a volt meter....just looking won't tell you much.

Jan 11, 2010 | 1992 Jeep Wrangler

Not finding what you are looking for?
1992 Jeep Wrangler Logo

Related Topics:

646 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...