Question about 1983 Subaru DL

Open Question

1980 subaru DL 1.6 liter 5 Speed tranny

The transmission is stuck in two gears ! any idea on how to fix it or where
to go on internet for a pic of the inside of the 5 speed tranny? thank you

Posted by on

5 Suggested Answers

SOURCE: 94 dodge neon auto tranny

Hi,

Here is some possible reasons why your transmission is having those problems .

* The gear shift linkage is binding
* There is an internal problem in the transmission
* The throttle cable is broken or disconnected
* The vacuum modulator on the transmission is faulty or the vacuum line is damaged
* The electronic transmission control circuit may be faulty

Posted on Feb 26, 2009

  • 168 Answers

SOURCE: how to remove transmission , how to replace reverse gear?

Are you sure that it is gone? make sure the all the bushing on the transmission are good it maybe that it is not able to go all the way in gear. If you do need to take it out get a good manual "Bentley" are the best it will show you the inside of the transmission too. Haynes are also good but not for working on the transmission it self

Posted on Mar 04, 2009

  • 1 Answer

SOURCE: transmission input speed sensor location

It is located on the front of the transmission. you will see 2 of them one on the left under small transmission lines it is the input then to the right behind the radiator overflow there is the other one. Easiest way to change them is with a 1" deep well socket

Posted on Jun 02, 2009

  • 245 Answers

SOURCE: 2000 Subaru Outback manual transmission rebuild

I would want to see that for myself, or get a second opinion. That really sounds suspicious since they claimed there was rust in a box that was mostly filled with oil. And I can't see any logic in paying a lot of money to fix a transmission that is working. Why don't you take it to another shop and ask them to change the transmission oil, and to save the old oil for you to look at. It would be even better to change the oil yourself. Don't tell the dealer what you are doing. The best thing would be to just pick up your car, as is. If it is a scam, they could put some stuff in the transmission if you give them time to do it. In fact, they may have already done that. I can't say it's a scam, but it sounds like it could be if you haven't done anything that would have broken off teeth in the transmission. And if teeth are broken off you should be able to hear it while accelerating at low speed in each gear.

Posted on Sep 13, 2009

Testimonial: "Thanks for your suggestions. Today we found an independent mechanic recommended on Car Guys web site. We'll talk w/ him on Monday."

  • 40 Answers

SOURCE: 5 speed manual transmission really hard to shift/change gears

The transmition is not the problem. The cables that run from the shifter to the transmition are the culpret. I recently rescued my wife from the road when the linkage broke on our VUE. I purchased new connectors and cables from the dealership and replaced them. For those that have the proper knowledge and skill set, you can replace them yourself. Others are better off having it done at a shop. The following is my personal experience and is not meant to be a guide, repair manual or procedure for those who lack formal automotive repair training! The new shifter cables come as a set. The cable with the white housing does not seem to be a problem. The cable with the black housing controls the push forward-pull back and the cable with the white housing controls the side to side movement. I found that the new cable with the black housing had the same sort of stiffness when I pushed and pulled the cable by hand. Then I noticed that the cable end was bent, causing it to bind in the housing. I straightened the end by bending it with my hands untill I felt the least amount of binding or resistance when pushing and pulling it. When I installed it the difference was amazing! I kept the old cable set for emergencies. The only tools you need to replace the cables and couplings are a 7mm socket on a screwdriver handle, a phillips head screwdriver and a pair of needle nose plyers. Remove the center console, (4, 7mm screws) and electrical connections. Then remove the plastic panels around the shifter, (7, phillips head screws and 2 plastic push pins) associated snap together panel fasteners and electrical connections. Pop each cable end off it's shifter joint/ball and push the collar back on each cable housing anchor. Pull the carpet back and push the rubber grommet through the firewall in the passenger footwell. Then pop the cable ends off at the transmition. Pull the old cable set out and reverse the procedure to install the new cables. There is an adjustment of the cable length. This should be done before replacing the plastic panels and center console. The new cable ends that attach to the shifter can be positioned/adjusted. Looking at the old cable pair you will see where the old clips were positioned and can start with that. Then run the shifter through all the gears to make sure they all engage. If you run out of travel on the shifter handle re-position the clips on the cable ends, as needed, to get full gear engagement without running out of travel.

Posted on Aug 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How many qts of oil do i need


Depends on your engine.

1980 JEEP CJ-7 2.5L 4-cyl Engine Code [B]
CAPACITIES
Engine, GM without filter..........2.4 quarts[1]
Wix Filter ........ 51040
Cooling System, Initial Fill..........8.0 quarts
Automatic Transmission, A904, 30RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, A999, 32RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, Total Fill
3 speed A999, 32RH..........8.4 quarts
3 speed A904, 30RH..........7.0 quarts
Manual Transmission, 4-SPD, SR-4..........3.0 pints
Manual Transmission, 4-SPD, T176..........3.6 pints
Differential, Front..........2.5 pints[3]
Differential, Rear..........4.9 pints
Transfer Case,..........4.0 pints

1. Add extra oil when replacing filter. After refill check oil level.
2. With engine automatic transmission operating temperature, shift through all gears.
Check fluid level in NEUTRAL and add fluid as needed.
3. 1984-1992 Models with command-Track, add 5 oz of 75W-90 GL-5 to shift motor housing opening.

TORQUES
Oil Drain Plug.....25 ft-lbs
Manual Transmission T176
Fill Plug.....15 ft-lbs
Drain Plug.....15 ft-lbs
Manual Transmission SR4
Fill Plug.....20 ft-lbs

1980 JEEP CJ-7 4.2L 6-cyl Engine Code [C]
CAPACITIES
Engine, without filter..........5.0 quarts[1]
Wix Filter..... 51522
Cooling System, Initial Fill..........11.0 quarts
Automatic Transmission, A904, 30RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, A999, 32RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, Total Fill
3 speed A999, 32RH..........8.4 quarts
3 speed A904, 30RH..........7.0 quarts
Manual Transmission, 4-SPD, SR-4..........3.0 pints
Manual Transmission, 4-SPD, T176..........3.6 pints
Differential, Front..........2.5 pints[3]
Differential, Rear..........4.9 pints
Transfer Case,..........4.0 pints

1. Add extra oil when replacing filter. After refill check oil level.
2. With engine automatic transmission operating temperature, shift through all gears.
Check fluid level in NEUTRAL and add fluid as needed.
3. 1984-1992 Models with command-Track, add 5 oz of 75W-90 GL-5 to shift motor housing opening.

TORQUES
Oil Drain Plug.....30 ft-lbs
Manual Transmission T176
Fill Plug.....15 ft-lbs
Drain Plug.....15 ft-lbs
Manual Transmission SR4
Fill Plug.....20 ft-lbs

1980 JEEP CJ-7 5.0L 8-cyl Engine Code [H]
CAPACITIES

Engine, without filter..........4.0 quarts[1]
Wix Filter..... 51258
Cooling System, Initial Fill..........13.0 quarts
Automatic Transmission, A999, 32RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, A904, 30RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, Total Fill
3 speed A904, 30RH..........7.0 quarts
3 speed A999, 32RH..........8.4 quarts
Manual Transmission, 4-SPD, SR-4..........3.0 pints
Manual Transmission, 4-SPD, T176..........3.6 pints
Differential, Front..........2.5 pints[3]
Differential, Rear..........4.9 pints
Transfer Case,..........4.0 pints

1. Add extra oil when replacing filter. After refill check oil level.
2. With engine automatic transmission operating temperature, shift through all gears.
Check fluid level in NEUTRAL and add fluid as needed.
3. 1984-1992 Models with command-Track, add 5 oz of 75W-90 GL-5 to shift motor housing opening.

TORQUES
Manual Transmission T176
Fill Plug.....15 ft-lbs
Drain Plug.....15 ft-lbs
Manual Transmission SR4
Fill Plug.....20 ft-lbs

Oilman

Feb 02, 2013 | 1984 Jeep CJ7

1 Answer

How do i repair the shifter cable on a 2000 ford escort zx2 with a 5 speed manual transmission


My escort is stuck in fourth it's not the clutch or the shifter I have no clue it's moves right where it goes into the tranny but it's stuck in high gear and just is really boggy

Jun 23, 2012 | Cars & Trucks

1 Answer

My 97 chevy s-10 pickup is a 5 speed with a 4.3 engine and our truck is stuck in first gear. Should we buy a new one or have someone look at it?


If it's stuck in 1st gear you probably need a new transmission. I'd fix it. A used tranny at a salvage yard is probably about $250.00 and not that hard to replace.

Mar 08, 2010 | 1997 Chevrolet S-10 Pickup

1 Answer

Fluid capacities and fluid specs


2000 TOYOTA TACOMA 2.7L 4-cyl Engine Code 3RZ-FE

Engine Oil Grade 1......API* All TEMPS......5W-30 Optional ..10W-30
Engine, 2WD, with filter..........5.5 liters
Engine, 4WD, with filter..........5.4 liters

Manual Transmission,......GL-5/ GL-4 All TEMPS......75W-90
Automatic Transmission,A340E......AF3 / A43D......AF3

Differential, Front/ Rear W/ ADRD......GL-5 ALL TEMPS......75W-90
Differential, Front Less ADRD......GL-5 ALL TEMPS......80W-90

Transfer Case,......GL-4/GL-5 ALL TEMPS......75W-90 Gear oil.

Capacity:
Cooling System, Initial Fill..........8.5 liters
Automatic Transmission, A340E Initial Fill..........1.6 liters
Automatic Transmission, A340F Initial Fill..........2 liters
Automatic Transmission, A43D Initial Fill..........2.4 liters
Automatic Transmission, Total Fill
4 speed A340E..........7.2 liters
4 speed A340F..........10.1 liters
4 speed A43D..........6.5 liters
Manual Transmission, ..........2.5 liters
Differential, With ADRD Front..........1.2 liters
Differential, Without ADRD Front..........1.1 liters
Differential, 2WD V6 Rear..........2.6 liters
Differential, 4WD Extra Long Rear..........2.5 liters
Differential, Short WB With LSD Rear..........2.7 liters
Differential, Short WB Without LS Rear..........2.6 liters
Transfer Case, Electronic..........1.2 liters
Transfer Case, STD..........1 liters


Feb 09, 2010 | 2000 Toyota Tacoma PreRunner

2 Answers

Brake lights wont turn on


if you look at the brake pedal you will find 1 or more switches connected to it. one of them has gone bad. you can test them yourself with a continuity tester and your local auto parts store will be able to get you a new one.

Jul 24, 2009 | 1995 Subaru Impreza

1 Answer

The tranny keeps popping out of 4th gear and now 1st gear is too.Specaily when going down hill. 5 speed tranny. whats up?


Those split case transmissions werent that hard to separate and install new **** fork and syncros to affected gears. Sometimes it took the slider and dogs as well.

Jun 12, 2009 | 1992 Subaru Legacy

1 Answer

2002 Dodge Caravan, Tranny would shift, DTC P0700, P0725


replace the input speed sensor to transmission and the wiring pigtail all are available at your chrysler dealer take your vehicle registration in to the parts counter so they have your vin # to get the right part and it is the front of trans by fluid linres to radiator.

Mar 08, 2009 | 2002 Dodge Caravan

1 Answer

I recently swapped my tranny. its a super t 10 4 speed, it worked fine when i pulled it from the 1980 camaro, iput it in my other 1980 and now my transmission wont go in any of the gears, it will go into...


Did you adjust the shift rods from the shifter to the trans shift arms. Take your shift rods loose and put shifter in neutral, and transmission arms in neutral, then adjust the rods so they slide in. Then your shifter matches your transmission and you should be able to shift just fine.

Aug 14, 2008 | Chevrolet Camaro Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

80 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts

yadayada
yadayada

Level 3 Expert

70347 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6876 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...