Question about 2000 Chevrolet Silverado

1 Answer

Evap control system

Check engine light on read out p0440. where do i start looking for leaks&is there something i can spray on the hoses to detect a leak?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 625 Answers

Unfortunatelly not the only way to locate those leaks is with a smoke machine than aply smoke to the evaporative system but a loose fuel cap will give you this code or if you fill the tank with truck runing that also will set code after a few minutes of driving.
so make sure the fuel cap is tie and reset the code if code comes back then have it inspect for leaks

Posted on Jun 02, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Engine codes p0440,p0441


code po440 refers to evaporative emission (EVAP) system--malfunction ===causes --hose connections --intake leak--EVAP canister purge valve
code p0441 refers to EVAP system--incorrect flow detected===causes---hose connections --intake leak--EVAP canister purge valve.
once you fix the fault use a scanner to reset the engine light.

Apr 09, 2014 | 2005 Chrysler Town and Country

1 Answer

Hello there,my 2001 echo is lighting up trouble codes p0440 p0441 p0446; how and where should i start?


code p0440 refers to evaporative emission (EVAP) system--malfunction=== causes --hose connections --intake leak--EVAP canister purge valve
code po441 refers to EVAP --incorrect flow detected==causes the same as for po440
code po446 refers to EVAP system vent control --circuit malfunction===causes --wiring---EVAP can purge valve--ECM
generally I would replace the purge valve as it is common to all codes

Feb 03, 2014 | Cars & Trucks

2 Answers

Pontiac Bonneville SE coming up with ODB2 scanner codes P0301 and P0440


Hi Becca:
P0301 Code - Cylinder #1 Misfire Detected
A P0301 code means that the the car's computer has detected that one of the engine's cylinders is not firing properly. In this case it's cylinder #1.

Symptoms may include:
the engine may be harder to start
the engine may stumble / stumble, and/or hesitate
other symptoms may also be present

A code P0301 may mean that one or more of the following has happened:
Faulty spark plug or wire
Faulty coil (pack)
Faulty oxygen sensor(s)
Faulty fuel injector
Burned exhaust valve
Faulty catalytic converter(s)
Running out of fuel
Poor compression
Defective computer

Possible Solutions:
- If there are no symptoms, the simplest thing to do is to reset the code and see if it comes back.
- If there are symptoms such as the engine is stumbling or hesitating, check all wiring and connectors that lead to the cylinders (i.e. spark plugs). Depending on how long the ignition components have been in the car, it may be a good idea to replace them as part of your regular maintenance schedule. I would suggest spark plugs, spark plug wires, distributor cap, and rotor (if applicable). Otherwise, check the coils (a.k.a. coil packs). In some cases, the catalytic converter has gone bad. If you smell rotten eggs in the exhaust, your cat converter needs to be replaced. I've also heard in other cases the problems were faulty fuel injectors.


P0440 Code - Evaporative Emission Control System Malfunction
This indicates that a part of the EVAP control system is no longer fuctioning correctly. The EVAP system consists of many parts, including (but not limited to) the gas cap, fuel lines, carbon canister, purge valve, and other hoses. The (EVAP) emission control system prevents the escape of fuel vapors from a vehicle's fuel system. Fuel vapors are routed by hoses to a charcoal canister for storage. Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engine.

You likely won't notice any drivability problems.

A code P0440 could mean one or more of the following has happened:
The gas cap is not installed or working properly
The purge solenoid has failed
The canister is plugged and not working properly

With a P0440 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:
Remove and reinstall the gas cap, clear the code, and drive for a day and see if the codes come back.
Inspect the EVAP system for cuts/holes in tubes/hoses
Inspect for damaged or disconnected hoses around the Evap purge solenoid
Check and/or replace the sensor
Check and/or replace the purge valve
Have a professional use a smoke machine to detect leaks

Other EVAP DTCs: P0440 - P0441 - P0442 - P0443 - P0446 - P0453 - P0455 - P0456-

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Feb 15, 2012 | Pontiac Bonneville Cars & Trucks

1 Answer

Have had check engine light on over a year first code p0442 changed gas cap' purge soleniod,charcoal canisterdidnt work changed leak detection pump now codes p0440 and p0499 are coming up any idea


you can look this obd2 trouble code table.
for p0440, you can try this:

Remove and reinstall the gas cap, clear the code, and drive for a day and see if the codes come back.

Inspect the EVAP system for cuts/holes in tubes/hoses

Inspect for damaged or disconnected hoses around the Evap purge solenoid

Check and/or replace the sensor

Check and/or replace the purge valve

Have a professional use a smoke machine to detect leaks

Aug 04, 2011 | Dodge Dakota Cars & Trucks

1 Answer

It is coming up with p440 code


P0440 - Evaporative Emission Control System Malfunction

This indicates that a part of the EVAP control system is no longer fuctioning correctly. The EVAP system consists of many parts, including (but not limited to) the gas cap, fuel lines, carbon canister, purge valve, and other hoses. The (EVAP) emission control system prevents the escape of fuel vapors from a vehicle's fuel system. Fuel vapors are routed by hoses to a charcoal canister for storage. Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engine.

Symptoms: You likely won't notice any drivability problems.

Causes: A code P0440 could mean one or more of the following has happened:
* The gas cap is not installed or working properly
* The purge solenoid has failed
* The canister is plugged and not working properly

Possible Solutions: With a P0440 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:
* Remove and reinstall the gas cap, clear the code, and drive for a day and see if the codes come back.
* Inspect the EVAP system for cuts/holes in tubes/hoses
* Inspect for damaged or disconnected hoses around the Evap purge solenoid
* Check and/or replace the sensor
* Check and/or replace the purge valve
* Have a professional use a smoke machine to detect leaks

Other EVAP DTCs: P0440 - P0441 - P0442 - P0443 - P0446 - P0453 - P0455 - P0456

Keep us updated and remember to rate this answer..

Feb 01, 2011 | Chevrolet Venture Cars & Trucks

1 Answer

What p0440 mean in the cars


P0440 OBD-II - Evaporative Emission Control System Malfunction


What does that mean?
This indicates that a part of the EVAP control system is no longer fuctioning correctly. The EVAP system consists of many parts, including (but not limited to) the gas cap, fuel lines, carbon canister, purge valve, and other hoses. The (EVAP) emission control system prevents the escape of fuel vapors from a vehicle's fuel system. Fuel vapors are routed by hoses to a charcoal canister for storage. Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engine.



Symptoms:
FB.init("dd7d9e9681341cde77587bc6a2029f6f"); OBD-Codes.com on Facebook You likely won't notice any drivability problems.



Causes:
A code P0440 could mean one or more of the following has happened:
  • The gas cap is not installed or working properly
  • The purge solenoid has failed
  • The canister is plugged and not working properly

Possible Solutions:With a P0440 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:
  • Remove and reinstall the gas cap, clear the code, and drive for a day and see if the codes come back.
  • Inspect the EVAP system for cuts/holes in tubes/hoses
  • Inspect for damaged or disconnected hoses around the Evap purge solenoid
  • Check and/or replace the sensor
  • Check and/or replace the purge valve
  • Have a professional use a smoke machine to detect leaks

Hope helps (remember rated this).

Jul 05, 2010 | 1999 Chevrolet Blazer

3 Answers

Check engine light came on, says its a evaporative emission system, code# P0440, what is that?


What does that mean?
This indicates that a part of the EVAP control system is no longer fuctioning correctly. The EVAP system consists of many parts, including (but not limited to) the gas cap, fuel lines, carbon canister, purge valve, and other hoses. The (EVAP) emission control system prevents the escape of fuel vapors from a vehicle's fuel system. Fuel vapors are routed by hoses to a charcoal canister for storage. Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engine.

Possible Causes:
A code P0440 could mean one or more of the following has happened:
  • The gas cap is not installed or working properly
  • The purge solenoid has failed
  • The canister is plugged and not working properly
Possible solutions:
With a P0440 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:
  • Remove and reinstall the gas cap, clear the code, and drive for a day and see if the codes come back.
  • Inspect the EVAP system for cuts/holes in tubes/hoses
  • Inspect for damaged or disconnected hoses around the Evap purge solenoid
  • Check and/or replace the sensor
  • Check and/or replace the purge valve
  • Have a professional use a smoke machine to detect leaks
HTH,

Mike...

Dec 04, 2009 | 1996 Chevrolet Cavalier

3 Answers

2000 cavalier check engine light code po440


P0440 - Evaporative Emission (EVAP) System


evaporative emission (EVAP) system has a large leak.
Check the gas cap or vent valve. these are the most common problems.


The Powertrain Control Module (PCM) at different times performs various tests on the EVAP system. OBD II Enhanced EVAP systems are in place to keep fuel tank vapors from venting into the atmosphere, and instead purges them into the engine to be burned. Regular pressure tests are conducted by the PCM to monitor the sealed system for leaks. The PCM monitors the EVAP system pressure by watching the Fuel tank pressure sensor (FTP). When the sensor indicates a small leak in the EVAP system, this code is set.


Here are some additional causes.

* A small leak in any of the EVAP hoses or fuel tank hoses
* A small leak in the purge valve or vent valve
* The EVAP Canister may be leaking

Jun 06, 2009 | 2003 Chevrolet Cavalier

3 Answers

Want does p0440 code mean


P0440 - Evaporative Emission (EVAP) System

This indicates that a part of the EVAP control system is no longer functioning correctly. The EVAP system consists of many parts, including (but not limited to) the gas cap, fuel lines, carbon canister, purge valve, and other hoses. The (EVAP) emission control system prevents the escape of fuel vapors from a vehicle's fuel system. Fuel vapors are routed by hoses to a charcoal canister for storage. Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engine.

Please rate and have a great evening:)

Apr 23, 2009 | Chevrolet Astro Cars & Trucks

1 Answer

I have a 2001 grand am se p0440 code comes up


This indicates that a part of the EVAP control system is no longer fuctioning correctly. The EVAP system consists of many parts, including (but not limited to) the gas cap, fuel lines, carbon canister, purge valve, and other hoses. The (EVAP) emission control system prevents the escape of fuel vapors from a vehicle's fuel system. Fuel vapors are routed by hoses to a charcoal canister for storage. Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engine.
Causes:
A code P0440 could mean one or more of the following has happened:
  • The gas cap is not installed or working properly
  • The purge solenoid has failed
  • The canister is plugged and not working properly

With a P0440 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:
  • Remove and reinstall the gas cap, clear the code, and drive for a day and see if the codes come back.
  • Inspect the EVAP system for cuts/holes in tubes/hoses
  • Inspect for damaged or disconnected hoses around the Evap purge solenoid
  • Check and/or replace the sensor
  • Check and/or replace the purge valve
  • Have a professional use a smoke machine to detect leaks

Feb 20, 2009 | 2001 Pontiac Grand Am SE

Not finding what you are looking for?
2000 Chevrolet Silverado Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...