Question about 2000 Ford Ranger SuperCab

1 Answer

Cant get the new fan belt back around pully - 2000 Ford Ranger SuperCab

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 62 Answers

First, be sure that it is the correct belt for your application and be sure that it is routed properly. Now, using 3/8 inch or 1/2 inch ratchet, stick into the idler pulley to reposition the pulley so that it allows for the belt to be put back on properly. Remove ratchet and check belt tension. If everything appears to be in order, start car and observe that belt will remain in position. Hopefully, this will help to FixYa problem!

Posted on Oct 11, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Want to fit fan belt cant find the proper way


You have to find the tension pully. using a 3/8 socket wrench. not the socke but the actual wrench. place the square end of the wrench into the notch on the pully and either push or pull (depends on the v-belt system) and it should move. place your v-belt around the pully's according to the diagram under your hood leaving your tension pully to be the last one the belt goes on. Move that tension pully as mentioned above and place it the belt on the pully. The diagram under the hood should also show you where that tension pully is located.

Oct 04, 2010 | Ford Fusion Cars & Trucks

2 Answers

How do i put the power steering belt in a 1989 cadillac


There are two bolts to loosen. One is in the hole on the pulley. The other is on the bottom behind the pulley. Both were 15mm bolts. I had to take the upper fan shroud off, and the fan and clutch off to get to the botttom bolt. Once loosened, pry the power steering pump/pulley closer and put the belt on. Then pry it back and tighten the bolts.

Dec 17, 2009 | 1989 Cadillac Brougham

1 Answer

Need to change timming belt 1997 geo tracker


TIMING BELT CHANGE You should have some mechanical skills before attempting any engine maintenance! These are basic instructions, and you must knoe what you removed, when, and what order so you can reinstall them in order. First, you have to remove everything in the way! You need to remove the Fan, clutch, and shroud, pump pully & drive belts. Next, you need to remove the Crank Pully:

1. Crank Pully Bolt 2. Crank Pully 3. Center Bolt 4. 5mm Hex drive (used to remove pully bolts) Once the fan stuff, and pully(s) are removed, then you need to remove the Timing Belt cover:

Once the cover is removed, you will need to loosen the adjusting nut and pully bolt on the Belt Tensioner:
A. Adjust Nut B. Pully Bolt C. TENSIONER PULLY Once the the Adjust Nut, and Pully bolt are loose, move the pully as far towards the water pump as possible.
Then, you can slip the timing belt from the sprockets. Check the tensioner for roughness and excess play! DO NOT MOVE THE CAM OR CRANK SPROCKETS! IF you do, then you will have to line up the Crank and Cam for piston number one at Top Dead Center before placing the new timing belt on! Note the timing marks on the crank and camshaft sprockets. IF YOU MUST! Allign the Cam and Crank at piston#1, Top Dead Center before removing the belt. Each sprocket has a small hole, with a line through it, and there is a small groove or "V" it alligns with on the engine. Now, once the timing belt is off, look at your new timing belt. Older belts use the Squared off teeth, while new ones have the rounded teeth. Make sure you have the correct belt for your sprockets! Never reinstall a belt that is in questionable condition. BELT WEAR CONDITIONS
If there are Arrows on the belt, they must be pointing to the RIGHT when you put the new belt on the sprockets. If there isn't one, then paint one on, and place the belt back on the sprockets. The arrow will indicate to a mechanic, this is the way the belt must be put back on (if they replace any cam or crank oil seals). Slip the new belt onto the Crank sprocket. While maintaining tension on the side of the belt opposite the tensioner, slip the belt onto the Camshaft sprocket. Releace the Tensioner adjusting nut to allow spring tension against the belt. Temporarily reinstall the crank pully, taking care to align the notch in the pully with the raised area on the sprocket. Rotate the crank clockwise two complete revolutions. Recheck the alignment of the of the valve timing marks. If they do not align properly, loosen the tensioner, slip the belt off the crank pully, align the timing marks, reinstall the belt, and check alignment again. Tighten the tensioner nut, then the bolt. Reinstall all parts removed, in the opposite order, of course. Start the engine and allow to reach normal operating temp, then road test. THEORETICALLY, you should simply be able to replace the belt with the new one, and go, as long as you did not move any of the sprockets when removing or installing the belt. Most people do it this way, and do not test for alignment before replacing everything. When the belt wears, timing will be off, very little, and this is why you check alignment. The belt may have slipped a tooth, making the timing off. This is why the Cam and Crank sprockets must both align properly. An experienced person will do just that: Replace the belt, and go. It really isn't all that hard. It helps to have a second person around with some experience also.

Nov 11, 2009 | 1997 Geo Tracker 2 Door

2 Answers

My serpintine fan belt came off as I started the motor; w/o air conditioner, but it does have power steering- the new belt seems to be too long, even though I had brought in the old one and followed the...


All it takes is for one part of the belt to be in the wrong position for it to appear to be too long. Check the diagram again. There is often a diagram in the owner manual as well as under the hood.

Oct 15, 2009 | 1989 Chevrolet G20

1 Answer

How doe's the fan belt go around pully wheels on a Lreg merc c180 thanks


Tricky one...... however serpentine belts always double back on them selves to maximise friction and taughtness, as a rule these go round the pullies and the double back to go around the tensioner. Try placing them around the pullies and the pulling the belt between them towards the tensioner!

Sep 13, 2009 | 1991 Mercedes-Benz Mercedes Benz C Class

1 Answer

Belt inst


For the 3.0L Vulcan, you have a tensioner that is located just below the power steering pully. Use a 15mm wrench or the 15mm shallow well socket that comes in a Serpentine Belt tool to push the tensioner toward the rear of the engine compartment. Take the old belt off and route the new belt. The belt begins at the crankshaft pully, goes under and around the a/c compressor, up around the power steering pump, around (with the flat edge) the idler pully, around the alternator, the flat edge then sits against the tensioner and back around to the water pump pully. You should have a belt routing diagram on the underside of the hood just above the serpentine pully assembly.

Jun 23, 2009 | 1999 Ford Taurus

1 Answer

Cant put on belt right


from front of engine looking back,belt around bottom of crank pully,water pump is just above,left side of belt comes around water pump going counter clock wise,put belt over alternator,then straight across to a/c compressor,(make sure belt goes under any idler pullies,smooth side of belt to smooth side of pully)find your belt tensioner,pry back on tensioner(be carefull)and carefully place belt under roller pully of the tensioner,release and check allignment of belt prior to starting.oh ya make sure belt is in good condition.

Mar 01, 2009 | 1991 Chevrolet C1500

2 Answers

How do i change the fan belt


well has soon as you loosen and take out the alt the belt will become loose then put alt on it will slide down to put belt around and then pull up on alt and tighten it up

Jan 25, 2009 | 1988 Mazda B2200

1 Answer

Cant seem to tighten the fan belt or the onein front of it?


are you sure you are putting the belt on right? there may be a pully ur missing that the belt has to go around.

Jan 08, 2009 | 1997 Nissan Pathfinder

Not finding what you are looking for?
2000 Ford Ranger SuperCab Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...