Question about 2000 Ford Mustang

1 Answer

DO I have to drop the motor and transmissom together or can i drop the bellhouse and transmissom by its self out of a 2000 mustang Gt.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 662 Answers

Being rear wheel dirive, it is possible to remove the transmission and bellhousing by themselves........

Posted on Oct 10, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 v6 pony water in oil . Like to drop 289 or 302 in her.Could it work


a mustang
current motor... head gasket blown ?

could drop a used low mileage motor 2000 mustang in

depends on emissions rules in your state

and engine bay space
think about .. drop a ford V8 Windsor with Holley carbs



26332078-tvvyms2bilrd4trwfnpfcz5t-3-0.jpg2000-v6-pony-water-in-oil-like-drop-tvvyms2bilrd4trwfnpfcz5t-3-2.jpg

Oct 29, 2016 | Cars & Trucks

1 Answer

Why does my mustang idle at 1700rpms....then drops back to 950....sometimes doesnt drop at all.....also hesitates a little while drivng....its a 92 gt,5 spd...any ideas?


take off your throttle body when you look inside you will see 2 needle like pieces they should look chrome get a can of throttle body cleaner and spray it till they look chrome color again put back together and you should be alright if not replace your throttle body.

Feb 13, 2011 | 1992 Ford Mustang

1 Answer

95 mustang gt how to change oil pan gasket


There is no simple way.. I have done it with the motor in and out.. It took less time to pull the motor and change the pan than it did to drop the cross member , undo the engine and trans mounts. I don't recommend doing it with the motor in.

Jul 28, 2010 | 1995 Ford Mustang

1 Answer

Putting a 302 in a 99 mustang


You'll need the K-member from a 94'-95' v6 or GT, along with the correct motor mounts. once you have that it should drop right in. But there are many more parts you'll need to make it work like a 5.0 tranny, exhaust, wiring, pcm, radiator, and maybe more. Look in the Ford Racing catalog and drop a 4.6L Cobra motor in there. A lot fewer parts to buy. Also if your state has car inspections the 5.0 is not OBDII, and should only be attempted if its going to be a "race only" car.

Jan 08, 2010 | 1999 Ford Mustang Cobra

1 Answer

How do u get to upper starter bolt on 4.6l on 2000 mustang gt


  1. Disconnect the battery ground cable. For additional information, refer to Section 414-01 .
  1. Raise and support the vehicle. For additional information, refer to Section 100-02 .
  1. Remove the red starter solenoid safety cap.
  1. Remove the starter solenoid nuts and position aside the wires.
  1. NOTE: To ease removal, remove the upper, concealed bolt first.
    Remove the three starter motor bolts.
81b30f9.gif
  1. Remove the starter motor.

Nov 01, 2009 | 2000 Ford Mustang

1 Answer

Need a diagram for removing a starter from a 2000 mustand gt


2000 ford came with a choice of engines... with out knowing which one, I will suggest a generic method.....
Remove the - (neg) cable from the battery.
With the vehicle on a secure surface, remove the power cable from the starter.

Remove the 2 bolts that secure the starter to the bellhousing. Pull the starter out and insert new starter.
Secure with bolts and torque to 35-40 lbs.
Connect cable.
Done..

Oct 08, 2009 | 2000 Ford Mustang

2 Answers

I have a 2003 ford mustang gt stick shift. clutch sliping


sounds like you have a worn or misadjusted clutch, but if your clutch is self adjusting meaning a operated with hydraulic pressure (Brake Fluid) then you could have leaking slave cylinder that maybe wetting the clutch disc with brake fluid causing a slippage, or just a worn clutch, in which case you will need to inspect inside bellhousing...

Sep 11, 2009 | 2003 Ford Mustang

1 Answer

Need to know what size bolts bolt together the bellhousing.


it is a 7/16 ths size bolt about two and a half inches long. i just pulled mine saturday

Feb 26, 2009 | 1983 Ford Mustang Hatchback

2 Answers

2000 mustang GT


you need to check your fuel pressure . but im sure your fuel pressure regulator is bad.

Aug 24, 2008 | 2000 Ford Mustang

1 Answer

CHANG SPARK PLUGS ON 4.6 2 VALVE FORD MOTOR.


all i did was lose the fuel injector rails and i could move them a lil to get a wrench in there to change them

Jul 06, 2008 | 2000 Ford Mustang

Not finding what you are looking for?
2000 Ford Mustang Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...